Summary of the content on the page No. 1
SyncMaster 460DRN-A
LCD Display
User Manual
Summary of the content on the page No. 2
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions)
Summary of the content on the page No. 3
Introduction Cables GND Cable (3) Others Shock Sensor Remote Control Batteries (AAA X 2) (Not available in all loca- tions) Sold separately DVI Cable LAN Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
Summary of the content on the page No. 4
Introduction Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume. ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only al- lowed for external devic
Summary of the content on the page No. 5
Introduction Rear Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The LCD Display 's configuration at the back may vary slightly depending on the LCD Display model. POWER S/W ON [ │ ] / OFF [O] Switches the LCD Display On/Off. POWER IN The power cord plugs into the LCD Display and the wall plug.
Summary of the content on the page No. 6
Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port PC / DVI / HDMI IN [PC / DVI / HDMI AUDIO IN] (PC/DVI/HDMI Audio Connection Terminal (Input)) PC / DVI / HDMI IN [HDMI] Connect the HDMI terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI ca- ble. PC / DVI / HDMI IN [RGB](PC Video Connection Terminal) Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) PC / DVI / HDMI IN [DVI] (PC Video Con- n
Summary of the content on the page No. 7
Introduction LAN (LAN Connection Terminal) USB(USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. Note The number of LCD Displays that can be connected to loopout may differ depending on the cables, signal source etc. With cables where there is no degradation or signal source, up to ten LCD Displays can be con- nected. Circuit Breaker A circuit-breaking unit designed to prevent fire or electric shock caused by an electric leakage. Side 1. Connect the GND wires to th
Summary of the content on the page No. 8
Introduction Note The ground (GND) is used to prevent product noise and to protect people from electric shock due to electric leakage. Remote Control Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequen- cy. POWER OFF Number Buttons DEL button + VOL - MUTE TV/DTV MENU INFO COLOR BUTTONS TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU G
Summary of the content on the page No. 9
Introduction DUAL/MTS PIP SWAP Turns the product On. 1. POWER Turns the product Off. 2. Off 3. Number Buttons Press to change the channel. The "-" button operates only for DTV. It is used to select 4. DEL button MMS (multi-channel) for a DTV. 5. + VOL - Adjusts the audio volume. Pauses (mutes) the audio output temporarily. This is dis- 6. MUTE played on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 7. TV/DTV Selects the TV and DTV mode
Summary of the content on the page No. 10
Introduction Press the button to change the input signal SOURCE. 18. SOURCE Changing the SOURCE is only allowed for external devices that are connected to the monitor at the time. This button is used to return to the immediately previous 19. ENTER/PRE-CH channel. 20. CH/P In TV mode, selects TV channels. 21.D.MENU DTV menu display 22.GUIDE Electronic Program Guide (EPG) display. Returns to the previous menu. 23. RETURN 24. Up-Down Left-Right but- Moves from one menu item to another horizontally,
Summary of the content on the page No. 11
Introduction SAP Mono ↔ SAP Mono 30. PIP Every time you press the button, a PIP screen appears. - This fuction does not work for this LCD Display. 31.SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. - This fuction does not work for this LCD Display.
Summary of the content on the page No. 12
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display. The figure shown below ("Check Signal Cable") appears on a black background when the LCD Display is working normally even though no video signal is detect
Summary of the content on the page No. 13
Troubleshooting • Do not use benzene, thinner or other flammable sub- stances, or a wet cloth. • We recommend that a SAMSUNG cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Ac
Summary of the content on the page No. 14
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely con- nected. Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. Q: "Check Signal Cable" message. A: Ensure that the signal cable is firmly connected to the PC or video sources. A: Ensure that the PC or video s
Summary of the content on the page No. 15
Troubleshooting Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The power Indicator blinks green. A: The LCD Display is currently saving the changes made to the settings to the OSD memory. Q: The screen is blank and the power indicator light is steady green or blinks every 0.5 or 1 seconds. A: The LCD Display is using its power management system. A: Press a key on the keyboard. Q: The screen is blank and it is blinking. A: If you see the "TEST GOOD" m
Summary of the content on the page No. 16
Troubleshooting Problems related to MagicInfo Note Making a Bootable USB Flash Disk. Q: Making a Bootable USB Flash Disk A: 1) You can turn a common 512-MB or bigger USB storage media into a bootable disk using a USB bootable disk creation tool. (For example, the HP USB Disk Storage For- mat Tool) A: 2) Copies the OS ghost image and executables to your USB disk. A: 3) Enter the BIOS menu of your set by pressing the F2 key in the BIOS logo screen. Then, enable the USB Boot First option by select
Summary of the content on the page No. 17
Troubleshooting Set the function in the BIOS-SETUP of the computer. (Refer to the Windows / Computer Manual). Q: How can I clean the outer case/LCD Panel? A: Disconnect the power cord and then clean the LCD Display with a soft cloth, using either a cleaning solution or plain water. Do not leave any detergent or scratches on the case. Do not let any water enter the LCD Display. Q: How can I play the video? A: The video supports the MPEG1 and WMV codecs only. Install the corresponding codec to pla
