Summary of the content on the page No. 1
User Manual
Innovative LCD Display Solutions
AP—10AV Series
DP—10AV Series
OP—10AV Series
UMUV.10-045V2
Summary of the content on the page No. 2
AP-10AV / DP-10AV / DP-10AV Series User Manual 1. Table of Content 1. Table of Content Page.1 2. Introduction A) Overview Page.2 B) Features Page.2 C) Dimension Diagrams Page.3-5 D) Technical Specifications Page.6 3. Installation A) Package Contents Page.7 B) Caution to the user Page.7 C) Cleaning Page.7 D) Precautions Page.8-9 4. Using the Sy
Summary of the content on the page No. 3
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction A. Overview This LCD monitor incorporates 10.4”color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance. A maxi- mum resolution of 800 x 600 is ideal for displaying complex graphics and high definition images. Other outstanding designs that enhance this LCD monitor’s performance
Summary of the content on the page No. 4
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams AP-10AV series Apr 05 P.3
Summary of the content on the page No. 5
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams DP-10AV series Apr 05 P.4
Summary of the content on the page No. 6
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction C. Dimension Diagrams OP-10AV series Apr 05 P.5
Summary of the content on the page No. 7
AP-10AV / DP-10AV / DP-10AV Series User Manual 2. Introduction Technical Specifications Panel 10.4" LCD Panel Display Type TFT LCD active matrix colour Resolutions 800 x 600 Response Time Tr=15ms, Tf=25ms Contrast Ratio 180:1 typical 2 Brightness 350 cd/m typical Monitor Pixel Pitch 0.264(H) x 0.264(V) Panel Colour 262,144 display colour Viewing Angle 60 / 60 / 55 / 40 (L / R / U / D) Storag
Summary of the content on the page No. 8
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Package Contents After unpacking the carton, check and see if the following items are included in good condition. Contact your supplier as soon as possible for replacing the missing / damaged items. ● 10.4” TFT LCD monitor ● RCA Cable (Optional For AV Version only) ● S-Video Cable (Optional For AV Version only) ● VGA Cable
Summary of the content on the page No. 9
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation D. Precautions Read all of these instructions and save them for later use. Follow all warnings and instructions on the product. Product ● Do not cover or block the vent holes in the case. ● Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots. They may cause accident fire, electric shock or fai
Summary of the content on the page No. 10
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation D. Precautions (Cont.) Power and extension cords 1. Do not allow anything to rest on the power cord. 2. Do not locate this product where persons will walk on the cord. 3. Use the proper power cord with correct attachment plug type. If the power source is 120V AC, use a power cord that has UL and C-UL approvals. If the power source is a
Summary of the content on the page No. 11
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views AP Series - Front View AP Series - Rear View Apr 05 P.10
Summary of the content on the page No. 12
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views (Cont.) DP Series - Front View DP Series - Rear View Apr 05 P.11
Summary of the content on the page No. 13
AP-10AV / DP-10AV / DP-10AV Series User Manual 3. Installation A. Product Views (Cont.) OP Series - Front View OP Series - Rear View Apr 05 P.12
Summary of the content on the page No. 14
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System B. I/O Outlet AP Series DP Series OP Series (5) (1) (2) (3) (6) (4) 1. DC IN ： Connect to DC power cable. 2. PC IN ： Connect to D-Sub 15 pin signal connector. 3. RCA IN ： Connect to the composite cable connector. (for AV series only) 4. S-Video IN ： Connect to the S-Video cable connector. (for AV series only) 5. USB IN ： Con
Summary of the content on the page No. 15
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System C. Installation Procedures This monitor is equipped with an auto-sensing power supply for voltage ranges 100~240V, 50~60Hz. Please follow the following instruction to install LCD monitor. 1. Make sure that the system power is turned off. 2. Plug the signal cable to the signal connector at the rear of PC and the rear of the LCD mo
Summary of the content on the page No. 16
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen Touchscreen used for UltraView products are manufactured by 3M. Here provide TM TouchWare Software includes touch screen drivers for your installing. Note: To configure the settings of the touchscreen, please refer to the TM TouchWare User Guideline Note: If you have a Microsoft® IntelliPoint® or Kensington®
Summary of the content on the page No. 17
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For Windows 95, 98, Me, NT4.0, 2000 & XP (Cont.) 7. Once installation is complete, restart the system. As the system restarts, Windows detects and loads the driver. ● For serial controllers, restart the system. As the system restarts, Win- dows detects and load the driver Note: This step is not necessary for Win
Summary of the content on the page No. 18
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For DOS (Cont.) 7. Type INSTALL followed by the source disk drive, the destination drive, and the destination directory. For example, the following command copies the files from Drive A (source drive) to Drive C (destination drive) and the \MTS\TOUCH directory : INSTALL A: C:\MTS\TOUCH 8. Press Enter. The
Summary of the content on the page No. 19
AP-10AV / DP-10AV / DP-10AV Series User Manual 4. Using the System D. Setup Touchscreen For DOS (Cont.) Loading the DOS Touchscreen Driver After you install the files for the DOS touchscreen driver, you must load the driver before you can run a DOS touch application or open the DOS Touchscreen control panel. You can run the DOS touchscreen driver from a full-screen DOS session within Window
Summary of the content on the page No. 20
