Summary of the content on the page No. 1
3-864-132-12 (1)
Trinitron Color
Computer Display
EN
Operating Instructions
F
Mode d’emploi
ES
Manual de instrucciones
C
CPD-520GS
© 1998 by Sony Corporation
Summary of the content on the page No. 2
Owner’s Record Hinweise • Aus ergonomischen Gründen wird empfohlen, die The model and serial numbers are located at the rear of the unit. Grundfarbe Blau nicht auf dunklem Untergrund zu Record the serial number in the space provided below. Refer to verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). these numbers whenever you call upon your dealer regarding this • Aus ergonomischen Gründen (flimmern) sollten nur product. Darstellungen bei Vertikalfrequenzen ab 70
Summary of the content on the page No. 3
Getting Started TABLE OF CONTENTS Getting Started Precautions ........................................................................................................................... 4 Identifying Parts and Controls .......................................................................................... 5 Setup ...................................................................................................................................... 6 Automatically Adjusting the Size and Centerin
Summary of the content on the page No. 4
Getting Started Getting Started Warning on power connection Precautions • Use an appropriate power cord for your local power Installation supply. For the customers in the U.S.A. • Prevent internal heat build-up by allowing adequate air If you do not use the appropriate cord, this monitor will circulation. Do not place the monitor on surfaces (rugs, not conform to mandatory FCC standards. blankets, etc.) or near materials (curtains, draperies) that may block the ventilation holes. Examples of plu
Summary of the content on the page No. 5
Getting Started Getting Started Identifying Parts and Controls See the pages in parentheses for further details. Rear Front
1 RESET (reset) button (page 17) 8 AC IN connector Resets the adjustments to the factory settings. Provides AC power to the monitor. 2 ASC (auto sizing and centering) button 9 Video input 1 connector (HD15) EN (page 7) Inputs RGB video signals (0.700 Vp-p, positive) and Automatically adjusts the size and centering of the SYNC signals. images. F 5 4 3 2 1 3 INPUT (inpu
Summary of the content on the page No. 6
Getting Started If your PC system is not compatible with DDC2AB and DDC2B+ Setup This monitor uses the No. 9 pin in the video signal connector for DDC2AB and DDC2B+ compatibility. Before using this monitor, check that the following items are Some PC systems which are not compatible with either DDC2AB or included in your carton: DDC2B+ may not accept the No. 9 pin. If you are not sure whether • Monitor (1) your PC system accepts the No. 9 pin or not, use the HD15 (Female) • Power cord (1) - HD15
Summary of the content on the page No. 7
Getting Started Getting Started Step 2: Connect the power cord Automatically Adjusting the Size and Centering of the Picture With the monitor switched off, connect one end of the power cord to the monitor and the other end to a power By pressing the auto sizing and centering (ASC) button, the outlet. size and centering of the picture are automatically adjusted to fit the screen. to a power outlet to AC IN
1 Turn on the monitor and computer. Power cord (supplied) 2 Press the ASC button. The pi
Summary of the content on the page No. 8
Getting Started 2 Press the ¬./> and >?// buttons to select “ OPTION,” and press the MENU button again. Selecting the Input Signal The OPTION OSD appears. This monitor has two signal input connectors (HD15 and OPTION 5BNC) and can be connected to two computers. When the ON power of both computers is on, select the input signal you want to view as follows. ZZ... 1 MIN UNLOCK 1 Turn on the monitor and both computers. MANUAL DEGAUSS 2 Press the INPUT button to select the HD15 or 5BNC input signal.
Summary of the content on the page No. 9
Customizing Your Monitor Getting Started Customizing Your Monitor Before adjusting Introducing the On-screen • Connect the monitor and the computer, and turn them on. • Select “ LANG” in the MENU OSD, then select Display System “ENGLISH” (see page 17). Most adjustments are made using the MENU OSD. Adjusting the Picture Brightness MENU OSD and Contrast Press the MENU button to display the MENU OSD. This MENU OSD contains links to the other OSDs described Once the setting is adjusted, it will be s
Summary of the content on the page No. 10
Customizing Your Monitor Using the CENTER On-screen Using the SIZE On-screen Display Display The SIZE settings allow you to adjust the size of the picture. Once the setting is adjusted, it will be stored in memory for The CENTER settings allow you to adjust the centering of the current input signal. the picture. Once the setting is adjusted, it will be stored in memory for 1 Press the MENU button. the current input signal. The MENU OSD appears. 1 Press the MENU button. MENU The MENU OSD appears.
Summary of the content on the page No. 11
Getting Started Customizing Your Monitor 4 Press the >?// buttons to adjust the settings. Using the GEOM (Geometry) On- screen Display The GEOM (geometry) settings allow you to adjust the shape and orientation of the picture. Once the rotation is adjusted, it will be stored in memory for all input signals received. All other adjustments will be For Press stored in memory for the current input signal. ROTATION / . . . to rotate the picture clockwise 1 Press the MENU button. The MENU OSD appears.
Summary of the content on the page No. 12
Customizing Your Monitor Using the ZOOM On-screen Using the COLOR On-screen Display Display You can change the monitor’s color temperature. For example, you can adjust or change the colors of a picture on The ZOOM settings allow you to enlarge or reduce the the screen to match the actual colors of the printed picture. picture. Once the setting is adjusted, it will be stored in memory for Once the setting is adjusted, it will be stored in memory for all input signals received. the current input s
Summary of the content on the page No. 13
Getting Started Customizing Your Monitor 4 Fine tuning the color temperature Press the ¬./> buttons to select R (red), G (green), or B Using the SCREEN On-screen (blue) and adjust by pressing the >?// buttons. Display COLOR You can adjust convergence settings to eliminate red or blue 1 6500K 9300K shadows that may appear around objects on the screen. R 76 G 50 Adjust the CANCEL MOIRE function to eliminate wavy or B 50 elliptical patterns that may appear on the screen. Adjust the LANDING functio
Summary of the content on the page No. 14
Customizing Your Monitor Select To For Press select one of the four corners that BOT / . . . to shift red shadows up and blue shadows down LANDING needs color correction due to V CONVER BOTTOM influence from the earth’s magnetism ADJ correct the color at one of the four ? . . . to shift red shadows down and blue shadows up corners of the screen LANDING ADJUST turn the moire cancellation function “ON” or “OFF.” CANCEL MOIRE CANCEL MOIRE * / or ? . . . to select the corner of the must be “ON
Summary of the content on the page No. 15
Getting Started Customizing Your Monitor Changing the on-screen display position Using the OPTION On-screen Display You can change the OSD position (for example, when you want to adjust the picture behind the OSD). The OPTION OSD allows you to manually degauss the screen and adjust settings such as the OSD position and 1 Press the MENU button. power saving delay time. It also allows you to lock the The MENU OSD appears. controls. MENU Degaussing the screen The monitor screen is automatically deg
Summary of the content on the page No. 16
Customizing Your Monitor Setting the power saving delay time Locking the controls You can set the delay time before the monitor enters the The control lock function disables all of the buttons on the power saving mode. See page 19 for more information on front panel except the u (power) switch and MENU button. this monitor’s power saving capabilities. 1 Press the MENU button. 1 Press the MENU button. The MENU OSD appears. The MENU OSD appears. MENU MENU 2 Press the ¬./> and >?// buttons to selec
Summary of the content on the page No. 17
Getting Started Customizing Your Monitor Using the LANG (Language) On- Resetting the Adjustments screen Display Resetting an adjustment item English, French, German, Spanish, Italian and Japanese versions of the OSDs are available. 1 Press the MENU, ¬./> and >?//buttons to select the OSD containing the item you want to reset. 1 Press the MENU button. The MENU OSD appears. MENU MENU 2 Press the ¬./> buttons to select the item you want to reset. 2 Press the ¬./> and >?// buttons to select “ LANG,”
Summary of the content on the page No. 18
Technical Features Technical Features For input signals that do not match one of the factory preset modes, the digital Multiscan technology of this monitor Preset and User Modes performs all of the adjustments necessary to ensure that a clear picture appears on the screen for any timing in the This monitor has factory preset modes for the most popular monitor’s frequency range. However, it may be necessary industry standards for true “plug and play” compatibility. to fine tune the vertical/hori
Summary of the content on the page No. 19
Getting Started Technical Features You can set the delay time before the monitor enters the power saving mode using the OSD. Set the time according Power Saving Function to “Setting the power saving delay time” on page 16. This monitor meets the power-saving guidelines set by Note VESA and ENERGY STAR, as well as the more stringent If no video signal is input to the monitor, the “NO INPUT NUTEK . SIGNAL” message (page 20) appears. After the delay time has If the monitor is connected to a comput
Summary of the content on the page No. 20
Additional Information Additional Information 1 The input signal condition Warning Messages “OUT OF SCAN RANGE” indicates that the input signal is not supported by the monitor’s specifications. If there is something wrong with the input signal, one of the following messages appears. “NO INPUT SIGNAL” indicates that no signal is input, or the input signal from the selected input connector is not INFORMATION received. OUT OF SCAN RANGE 2 The selected input connector INPUT : HD15 Indicates w
