Summary of the content on the page No. 1
MOPS/586
Technical Manual
Rev. 1.4
®
JUMPtec
Industrielle Computertechnik AG
Brunnwiesenstraße 16
94469 Deggendorf/ Germany
Tri-M Systems Inc., 6-1301 Ketch Court, Coquitlam, B.C., V3K 6X7, Canada
Phone: (604) 527-1100, (800) 665-5600 Fax: (604) 527-1110
Email: info@Tri-M.com Web: www.Tri-M.com
Summary of the content on the page No. 2
MOPS/586 Table of Contents Table of Contents TABLE OF CONTENTS..........................................................................................................................................2 USER INFORMATION ............................................................................................................................................4 TRADEMARKS ................................................................................................................................
Summary of the content on the page No. 3
MOPS/586 Table of Contents FLOPPY CONNECTOR...............................................................................................................................................30 IDE CONNECTOR FOR 2,5" HARD DISK.....................................................................................................................31 ETHERNET CONNECTOR...........................................................................................................................................31
Summary of the content on the page No. 4
MOPS/586 User Information User Information ® Copyright 1997 JUMPtec Industrielle Computertechnik AG. ® In this document JUMPtec Industrielle Computertechnik AG will also be referred to by the short form ® "JUMPtec ". The information in this document has been carefully checked and is believed to be accurate and reliable. ® However, no responsibility is assumed for inaccuracies. Furthermore, JUMPtec reserves the right to make ® changes to any portion of this manual to improve reliability, function
Summary of the content on the page No. 5
MOPS/586 User Information Warranty Each board is tested carefully and thoroughly before being shipped. If, however, problems should occur during the operation, please check your user specific settings of all boards included in your system. This is often the source of the fault. If a board is defective, it can be sent to your supplier for repair. Please take care of the following steps: 1. The board returned should have the factory default settings since a test is only possible with these setting
Summary of the content on the page No. 6
MOPS/586 Features Features • Processor ® AMD Am5x86 with 133 MHz internal Clock and 16 kByte write-back-Cache • Chipset ALI 1489/1487 PCI Chipset • Power Supply 5V only supply • Memory 4 MB onboard and 4/8/16/32MB 5V-DIMM module DRAM with Fast Page Mode or EDO DRAM on the lower SO-DIMM-Connector • Ethernet 10BaseT (Twisted Pair) • Two serial ports, (COM1 and COM2) standard RS232C serial ports with FIFO, 16550 compatible • Parallel port, LPT1 With ECP/EPP-support • Floppy-interface • EIDE-PCI
Summary of the content on the page No. 7
MOPS/586 I/O Map I/O Map The I/O-port addresses of the processor module MOPS/586 are functionally identical with a standard PC/AT. I/O Addresses MOPS/586 - onboard Function 0000 - 001F X DMA-Controller 1 0020 - 003F X Interrupt-Controller 1 0040 - 0043 X Timer 0050 - 005F Onboard Control Registers 0060 - 0064 X Keyboard-controller 0061 X Port B Register 0070 X NMI Enable Register 0070 - 0071 X Real Time Clock 0080 - 008F X DMA Page Register 74LS612 0092 X Port A Register (Fast A2
Summary of the content on the page No. 8
MOPS/586 Memory Map for BIOS, SSD and JRC Support Memory Map for BIOS, SSD and JRC Support The BIOS includes two special extensions to support the onboard silicon state disk and Jumptec Remote Control. If the SSD is enabled in setup or the JRC client finds a host the code of the bios extension will be copied into shadow ram. The location where the biosextension is placed is automatically determined by the system bios . The user can not influence this! So care must be taken, when a Extended Memo
Summary of the content on the page No. 9
MOPS/586 Onboard SSD (DOS-compatible) Expanded Memory Map The user can convert (up to 20Mbytes) Extended Memory into Expanded Memory (EMS). The selected Expanded Memory is devided into 16KByte pages, of which four can be mapped into the EMS-frame. The EMS- frame is located within the first 1MByte address space and has a length of 64KByte. The start address of the EMS-page can be selected between CC000h and E0000h in steps of 16KBytes. Most Expanded Memory Managers are choosing their frame addres
Summary of the content on the page No. 10
MOPS/586 Block Diagram Block Diagram BIOS RTC LPT1 COM1 IO-Con- troller COM2 EIDE ALI Chipset DRAM Cache Ethernet- Con- 10baseT troller CPU ISA-Con. Tri-M Systems Inc., 6-1301 Ketch Court, Coquitlam, B.C., V3K 6X7, Canada Phone: (604) 527-1100, (800) 665-5600 Fax: (604) 527-1110 Email: info@Tri-M.com Web: www.Tri-M.com
Summary of the content on the page No. 11
MOPS/586 Connector Arrangement Connector Arrangement Tri-M Systems Inc., 6-1301 Ketch Court, Coquitlam, B.C., V3K 6X7, Canada Phone: (604) 527-1100, (800) 665-5600 Fax: (604) 527-1110 Email: info@Tri-M.com Web: www.Tri-M.com
Summary of the content on the page No. 12
MOPS/586 BIOS-Description BIOS-Description The Standard AMI-BIOS is located in the Flash EPROM onboard. This device has 8 bit wide access. 16 bit access is enabled by the shadow RAM feature (Standard). RTC-CMOS setup menu During boot sequence the CMOS setup can be entered by pressing the -key while the memory test is in progress. Main Menu • Standard CMOS Setup • Advanced CMOS Setup • Power Management Setup • Peripheral Setup • Auto-Detect Hard Disks • Change User Password • Change Sup
Summary of the content on the page No. 13
MOPS/586 BIOS-Description • WPcom (starting write precompensation cylinder) • Sec (number of sectors) Parameter Description Type The number for a drive with certain identification parameters. Cylinders The number of cylinders in the disk drive. Heads The number of heads. Write The size of a sector gets progressively smaller as the track diameter diminishes. Yet each sector must still hold 512 Precompensation bytes. Write precompensation circuitry on the hard disk compensates for the physi
Summary of the content on the page No. 14
MOPS/586 BIOS-Description Advanced CMOS Setup Quick Boot Set this option to Enabled to instruct AMIBIOS to boot quickly when the computer is powered on. This option replaces the former Above 1 MB Memory Test Advanced Setup option. The settings are: Setting Description Disabled AMIBIOS tests all system memory. AMIBIOS waits up to 40 seconds for a READY signal from the IDE hard disk drive. AMIBIOS waits for 0.5 seconds after sending a RESET signal to the IDE drive to allow the IDE drive time
Summary of the content on the page No. 15
MOPS/586 BIOS-Description Wait For 'F1' if Error If this option is Enabled the system will wait on power up for the user to press the key on any occurring error. The Optimal and Fail Safe default settings are Disabled. Hit ‚ Del‘ Message Display If this option is Enabled the system will display the String „Hit DEL if you want to run Setup“ on the screen while accepting the DEL key to enter setup. If the option is set to Disabled the string want be displayed. Internal Cache This op
Summary of the content on the page No. 16
MOPS/586 BIOS-Description Power Management Setup Power Management/APM If this option is Disabled, none of the below listed options are available, the system doesn't provide you with power save features. The Optimal and Fail Safe default settings are Disabled. Instant On Support Instant On is a Power Managment Software for Windows 95. Must be Enabled to support this Software. The Optimal and Fail Safe default settings are Disabled. Green PC Monitor Power State This option specifies the
Summary of the content on the page No. 17
MOPS/586 BIOS-Description Peripheral Setup Onboard IDE This option enables the onboard IDE controller. The settings are Disabled and Enabled. The Optimal and Fail Safe default settings are Enabled. Onboard FDC This option enables the floppy drive controller on the motherboard. The settings are Enabled or Disabled. The Optimal and Fail Safe default settings are Enabled. Onboard Serial Port1 This option enables serial port 1 on the motherboard and specifies the base I/O port address for s
Summary of the content on the page No. 18
MOPS/586 BIOS-Description This option enables the silicon state disk as either drive 80h, 81h, 82h, or 83h (C, D, E or F). The settings are Disabled, 80h, 81h,82h, 83h. The Optimal and Fail Safe default settings are Disabled. SSD Write Protect This option allows to write protect the silicon state disk. The settings are Disabled and Enabled. The Optimal and Fail Safe default settings are Disabled. SSD Erase On Next Boot If this option is set to Enabled, the silicon state disk will be era
Summary of the content on the page No. 19
MOPS/586 BIOS-Description AMIBIOS Configuration Screen AMIBIOS System Configuration (C) 1985-1996, American Megatrends Inc., Main Processor : Am5x86 (X5) Base Memory Size : 640KB Math Processor : Built-In Ext. Memory Size : 3072KB Floppy Drive A: : 1.44 MB 3½" Display Type : VGA/EGA Floppy Drive B: : None Serial Port(s) : 3F8,2F8 AMIBIOS Date : 07/15/95 Parallel Port(s) : 378 Pocessor Clock : 133MHz Power Management : Disabled Hard Disks(s) Cyl Head Sector Size LBA 32Bit Bl
Summary of the content on the page No. 20
MOPS/586 Hardware Description Hardware Description ALI-Chipset Features The MOPS/586 Board operates with the chipset ALI 1489/87, which provides following features: • 32 bit PCI Interface • integrated DRAM controller • integrated PMU controller • integrated PCI to ISA bridge (fully compliant to PCI 2.0) • enhanced DMA functions • build-in two 8259A interrupt controllers • fast PCI IDE Master Controller for ATA PIO mode 4 harddisks Memory configuration One memory bank for DRAM extension is l
