Summary of the content on the page No. 1
TUSB3210 Generic
Evaluation Board
User’s Guide
2005 MSP USB
SLLU031A
Summary of the content on the page No. 2
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the t
Summary of the content on the page No. 3
EVM IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation kit being sold by TI is intended for use for ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY and is not considered by TI to be fit for commercial use. As such, the goods being provided may not be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety measures typically found in the end product
Summary of the content on the page No. 4
EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input voltage range of 4 V to 6 V and the output voltage range of 3 V to 3.6 V. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible perm
Summary of the content on the page No. 5
Related Documentation From Texas Instruments Preface Read This First About This Manual This user’s guide describes the setup and operation of the TUSB3210 generic evaluation board. Familiarity with universal serial bus (USB) protocol and common laboratory testing equipment is required and assumed throughout this user’s guide. How to Use This Manual This document contains the following chapters: Chapter 1—Hardware and Software Required Chapter 2—EVM Operation Related Documentation From Texas
Summary of the content on the page No. 6
Trademarks Trademarks MacOS is a trademark of Apple Computer, Inc. Windows and Windows ME are trademarks of Microsoft Corporation. Other trademarks are the property of their respective owners FCC Warning This equipment is intended for use in a laboratory test environment only. It gen- erates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to subpart J of part 15 of FCC rules, which are designed to provide reasonab
Summary of the content on the page No. 7
Contents Contents 1 Hardware and Software Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 1.1 Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.2 Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1.3 Bill of Materials . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 8
viii
Summary of the content on the page No. 9
Chapter 1 Hardware and Software Required The TUSB3210 generic EVM is designed for use with a personal computer running a USB-enabled operating system. The PC should be USB 1.1 specification compliant. This implies that the BIOS, chipsets, and operating system are all USB 1.1 specification compliant. If the BIOS is not specification compliant, the system may not boot up when USB devices are connected at power up, and the EVM may not function. Note that an ac/dc power supply adapter is optional
Summary of the content on the page No. 10
Running Title—Attribute Reference 1.1 Equipment Figure 1 −1. TUSB3210 Evaluation Equipment USB EVM 1.2 Hardware Overview The TUSB3210 EVM hardware platform is 11 cm wide by 13 cm long. Throughout this document, text inside of parenthesis (ex.) denotes reference designators found on the TUSB3210 EVM. See Figure 1 −2 for a photograph of the EVM. All jumpers are installed with the factory settings. See the jumper table for a description of settings, and make any required adjustments before using th
Summary of the content on the page No. 11
Running Title—Attribute Reference TUSB3210 device. A USB cable should be plugged into a USB port on a PC or into a USB hub and connected to the TUSB3210 EVM type-B connector (U3). Figure 1 −2. TUSB3210 Evaluation Board Figure 1 −3. TUSB3210 EVM Connected to a Compact Flash Daughterboard Chapter Title—Attribute Reference 1-3
Summary of the content on the page No. 12
Running Title—Attribute Reference Figure 1 −4. TUSB3210 Printed-Circuit Board (REV 1.1)—Top Side 1-4
Summary of the content on the page No. 13
Running Title—Attribute Reference Figure 1 −5. TUSB3210 Printed-Circuit Board (REV 1.2)—Top Side Chapter Title—Attribute Reference 1-5
Summary of the content on the page No. 14
Running Title—Attribute Reference 1.3 Bill of Materials Item Quantity Reference Part 1 3 (REV 1.1 board) C1, C4, C10 Capacitor, 0.1 µF 1 7 (REV 1.2 board) C1, C4, C9, C10, C12, C13, C14 Capacitor, 0.1 µF 2 2 C2, C5 Capacitor, 4.7 µF 3 1 C3 Capacitor, 10 µF 4 3 C6, C7, C8 Capacitor, 22 pF 5 5 (REV 1.1 board) C9, C11, C12, C13, C14 Capacitor, 1 µF 5 1 (REV 1.2 board) C11 Capacitor, 1 µF 6 1 D4 LED, RUN (red) 7 4 G1, G2, G3, G4 CON1 8 1 JDP1 DB 9 −F (1 −2 −1 cable only) 9 1 JP1 Connector plug 25×2
Summary of the content on the page No. 15
Running Title—Attribute Reference 1.4 Schematic Diagram The complete schematic diagram of the TUSB3210 generic EVM is presented at the end of this document. Chapter Title—Attribute Reference 1-7
Summary of the content on the page No. 16
1-8
Summary of the content on the page No. 17
Chapter 2 EVM Operation This chapter describes the operation of the TUSB3210 EVM. Topic Page 2.1 TUSB3210 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.2 Interfaces and USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.3 Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2.4 Light Emitting Diodes (LEDs) . . . . . . . . . . . . . . .
Summary of the content on the page No. 18
Running Title—Attribute Reference 2.1 TUSB3210 Setup The TUSB3210 EVM supports many USB applications. The jumpers allow the flexibility to configure the EVM in various modes for evaluation purposes. Note that some modes require additional components not included with the EVM kit. The EVM comes in a default configuration that requires no additional components on the EVM. A full description of the TUSB3210 device is specified in the data manual (SLLS466). The PC must be running a USB-capable opera
Summary of the content on the page No. 19
Running Title—Attribute Reference 2.5 Jumpers and Switches Table 2 −2 is provided to help set up and configure the EVM platform jumpers to the desired mode of operation. The EVM can download firmware code from the PC through a loading program (which may or may not be supplied with your 2 EVM) or from an I C EEPROM. A 5-V power source may be supplied from an external source or from the USB cable. If supplied from an external source, U2 must be set to position 2 −3. If supplied from the USB cable
Summary of the content on the page No. 20
Running Title—Attribute Reference Figure 2 −1. GPIO Connector JP1 1 2 P0.0 P0.1 3 4 P0.2 P0.3 5 6 P0.4 P0.5 7 8 P0.6 P0.7 9 10 P1.1 P1.0 11 12 P1.3 P1.2 13 14 P1.4 P1.5 15 16 P1.6 P1.7 17 18 P2.0 P2.1 19 20 P2.3 P2.2 21 22 P2.4 P2.5 23 24 P2.6 P2.7 25 26 P3.0 P3.1 27 28 P3.2 P3.3 29 30 P3.4 P3.5 31 32 P3.6 P3.7 33 34 S2 S3 35 36 BS PUR 37 38 SCL1 SDA 39 40 SUSP 3.3 Susp 41 42 RST 1.8 V 43 44 3.3 V 3.3 V 45 46 5 V 5 V 47 48 GND GND 49 50 GND GND Connector Plug 25×2 2-4
