Summary of the content on the page No. 7
Make Connections to the Motherboard This section tells how to connect internal peripherals and power supply to the Motherboard. Internal peripherals include IDE devices (HDD, CD-ROM), Floppy Disk Drive, Chassis Fan, Front Panel Devices (Turbo LED, Internal Speaker, Reset Button, IDE LED, and KeyLock Switch.), Wake-On-LAN card, VGA card, Sound Card, and other devices. For more details on how to connect internal and external peripherals to your new SY-6IZM/3 Motherboard, please refer to SY-6IZM/3
Summary of the content on the page No. 8
Configure Memory 1 2 3 Set JP3 for power up FSB clock and AGP bus clock. JP3 is used to adjust AGP bus clock frequency depending on the value of the front side bus (FSB) clock, also the setting of the JP3 determines the power up FSB clock which will remain effective until the BIOS set the FSB clock to the CMOS setting. 3 3 2 2 JP3 Setting 1 1 Power up FSB Clock 66MHz 100MHz AGP Clock AGP Clock = FSB Clock ÷ 1 AGP Clock = FSB Clock ÷ 1.5 Note: The specification of maximum AGP bus Clock frequenc
Summary of the content on the page No. 9
Set the CPU Frequency You do not need to set any jumper for the CPU frequency. Instead, CPU settings are changed through the BIOS [SOYO COMBO SETUP]. Please refer to Chapter 3 - Quick BIOS Setup for details on how to set the Slot 1 processor frequency. Enable/Disable Power-On by PS/2 Keyboard (JP1) You can choose to enable the Power-On by PS/2 Keyboard function by shorting pin 2-3 on jumper JP1, otherwise, short pin 1-2 to disable this function. 3 3 2 2 1 1 Power Button Enable (JP8) Your syst
Summary of the content on the page No. 10
Enable/Disable Onboard VGA(JP7) The onboard VGA features of your Motherboard are controlled by jumper JP7.You can choose to enable or disable the available VGA function by setting JP7 accordingly. l Leave JP7 open to enable the onboard VGA function. Then, you can plug your VGA device monitor, after the Motherboard is installed. (You do not need to install any VGA card.) l To disable the onboard VGA options short pin JP7. Back Panel Connector PRT JOYSTICK PS/2 Mouse Connector USB2 PS/2 KB Conne
Summary of the content on the page No. 11
The 6IZM/3 Motherboard provides over-clocking capability. Due to the over-clocking setting your system may fail to boot up or hang during run time. If this occurs, please perform the following steps to recover your system from the abnormal situation: 1. Turn off system power (If you use a ATX power supply, sometimes you have to press the power button for more then 4 seconds to shut down the system) 2. Set the JP3 to pin 2-3 short if you use a FSB 66MHz CPU 3. Press and hold down the key
Summary of the content on the page No. 12
3 Quick BIOS Setup 3 This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [SOYO COMBO SETUP]. The [SOYO COMBO SETUP] menu combines the main CPU parameters that you need to configure, all in one menu, for a quick setup in BIOS. After the hardware installation is complete, turn the power switch on, then press the key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP U
Summary of the content on the page No. 1
SY-6IZM/3
Motherboard
Quick Start Guide
C
The SOYO CD Quick BIOS Hardware Introduction
Setup Installation
RECYCLED PAPER 100%
POST CONSUMER
FOR HOME OR OFFICE USE
With FCC Standards FC
Tested To Comply
Summary of the content on the page No. 2
SOYO ™ SY-6IZM/3 Motherboard ® ® m m * These specifications are subject to change without notice 2 6IZM/3 Serial - Version 1.0 - Edition: February 1999 "http://www.soyo.com.tw". on the Internet. The address is Web Site If you need any further information, please visit our document is subject to change without notice. however, no guarantee is given as to the correctness of the contents. The information in this installing the Motherboard. Information in this guide has been carefully checked for
Summary of the content on the page No. 13
4 The SOYO CD 4 Your SY-6IZM/3 Motherboard comes with a CD-ROM labeled "SOYO CD." The SOYO CD contains the user's manual file for your new Motherboard, the drivers software available for installation, and a database in HTML format with information on SOYO Motherboards and other products. Insert the SOYO CD into the CD-ROM drive The SOYO CD will auto-run, and the SOYO CD Start Up Menu will display as shown below. (SOYO CD Start Up Program Menu) The SOYO CD Start Up Program automatically detects
Summary of the content on the page No. 14
Please note that if the Start Up program was unable to determine which SOYO Motherboard you own, the manual selection menu will pop up, as shown below. Then select the user's manual file that corresponds to your Motherboard model name and click OK. SOYO CD Manuals Please select your manual In the box below and click OK. 6IZM/3 OK Back (Manual Selection Menu) The user's manual files included on the SOYO CD can be read in PDF (Postscript Document) format. In order to read a PDF file, the appropr
Summary of the content on the page No. 15
The following drivers are available for Windows 95 (Driver Installation Menu) The following drivers are available for Windows 98 (Driver Installation Menu) 15 The SOYO CD Quick Start Guide SY-6IZM/3
Summary of the content on the page No. 16
Ø Intel Because Windows 95 does not recognize the Southbridge of the newer Intel chipsets (TX, BX, ZX etc) this utility has to be run, it will update the necessary Windows files. (Only for Windows 95) Ø SOYO Without the busmaster drivers the CPU will need to be involved every time data is read from or written to the Harddisk. The busmaster drivers make use of DMA (Direct Memory Access) to relieve the CPU of this burden, thus speeding up the system. The SOYO SpeedPro driver makes use of an adva
Summary of the content on the page No. 17
Ø With this application program the user can make use of the on board sound chip. Before installing the YAMHA 740 Sound Drivers, you MUST first install the YAMAHA 740 drivers for Windows 9x or NT. Ø ATI Rage Pro AGP Select this Item and click OK to start up the ATI Rage PRO AGP driver screen. Follow the instructions on the screen to install the drivers and/or application programs you need. Note: Once you have selected a driver, the system will automatically exit the SOYO CD to begin the driver
Summary of the content on the page No. 18
Soyo Computer Inc., (Taiwan) Tel: 886-2-2290-3300 Fax: 886-2-2298-3322 Web Site: http://www.soyo.com.tw E-mail: info@mail.soyo.com.tw Soyo Tek Inc., (USA) Tel: (408) 452-7696 Fax: (408) 573-7696 Web Site: http://www.soyousa.com E-mail: sales@soyousa.com Soyo Europe B.V., (Holland) Tel: 31-79-3637500 Fax: 31-79-3637575 Web Site: http://www.soyo-europe.com http://www.soyo.nl E-mail: Sales@soyo.nl SAAT Technology GmbH, (Germany) Tel: 49-(0)441-204044 Fax: 49-(0)441-203422 Web Sites:http://www.saat.
Summary of the content on the page No. 3
1 Introduction 1 Congratulations on your purchase of the SY-6IZM/3 Motherboard. This Quick Start Guide describes the steps for installing and setting up your new Motherboard. This guide is designed for all users to provide the basic steps of Motherboard setting and operation. For further information, please refer to SY-6IZM/3 Motherboard User's Guide and Technical Reference online manual included on the CD-ROM packed with your Motherboard. Unpacking * If your board comes with a driver disc and a
Summary of the content on the page No. 4
SY-6IZM/3 Motherboard Layout PS/2 KB PS/2 Mouse Connector Connector N 1 3 1 1 FDC USB 1 USB 2 1 T Intel X 1 r 82443 ZX 3 1 1 21 VGA 4 WOL Header ATI Game Port 3 RAGE Pro 1 LINE-OUT W83977EF W 11 N K 3V 7 1 2 3 1 5 m IR1 M M M Battery M M M I I I D D D 5 3 CMOS Clear 4 J Jumper 1 AC97 J51 4 1 Codec N 1 Intel __ HDD LED 82371EB + A2 Speaker _ oTurb YMF740-V ++ D PWRBT 3 Keylock _ 0 Power d Reset M LED + 1 C A 8 2 8 e Flash BIOS g D Key Features ® Ø Supports Intel Pentium III processor (4
Summary of the content on the page No. 5
2 Installation 2 To avoid damage to your Motherboard, follow these simple rules while handling this equipment: l Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. l Remove the Motherboard from its anti-static packaging. Hold it by the edges and avoid touching its components. l Check the Motherboard for damage. If any chip appears loose, press carefully to seat it firmly in its socket. Follow the directions in this section designed to
Summary of the content on the page No. 6
Install the Motherboard Follow the steps below in order to perform the installation of your new SY-6IZM/3 Motherboard. Install the CPU Record the working frequency of your CPU that should be clearly marked on the CPU cover. FSB 66MHz FSB 100MHz To mount the processor that you have purchased separately, follow these instructions. T Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation. Failing to install these items may result in overheat
