Summary of the content on the page No. 1
CyberPro PCI 2S
Quick Installation Guide
Introducing the CyberPro PCI 2S
The CyberPro PCI 2S high-speed serial I/O card provides
two additional 9-pin serial ports.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, label prin
Summary of the content on the page No. 2
Package Contents • CyberPro PCI 2S board • Driver CD • Quick installation guide Layout JP2 (Serial port 2) Serial Port 2 Serial Port 1 JP1 (Serial port 1) Figure 1. Layout Jumper Settings (JP1, JP2) Open = 0 volts (default) Short 1-2 = 5V Short 2-3 = 12V Note: Most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information. 2
Summary of the content on the page No. 3
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal parts and handle cards only by their external edges. 1. Turn OFF the po
Summary of the content on the page No. 4
Driver Installation This section provides information on how to install the CyberPro PCI 2S drivers. Windows 95 1. At the Update Device Driver Wizard, click Next. 2. Insert the driver CD, and click Other Locations. Type in D:\9x, click OK, then Finish. (Change D: to match your CD-ROM drive letter) 3. From the Insert Disk window, click OK. When the Copying Files dialog box appears, type in D:\9x, then click OK. 4. Restart Windows to complete the installation. Windows 98/98SE 1. At the Add New Ha
Summary of the content on the page No. 5
Windows ME 1. At the Add New Hardware Wizard, select Specify the location of the driver (Advanced), click Next. 2. Insert the driver CD, check Specify a location, uncheck the other box, type in D:\Me, then click Next. (Change D: to match your CD-ROM drive letter) 3. Click Next, then Finish. 4. Repeat steps 1 and 2. 5. Click Next, Next, then Finish. 6. Restart Windows to complete the installation. To Verify Windows 95/98/98SE/ME Installation 1. From the main desktop, double click My Computer, Con
Summary of the content on the page No. 6
To Verify Windows NT 4.0 Installation 1. Click Start, Settings, Control Panel, double click Ports device icon. 2. Two new COM ports will be assigned when successfully installed. Windows 2000 1. At the Found New Hardware Wizard, click Next. 2. Select Search for a suitable driver for my device (recommended), and click Next. 3. Check Specify a location, uncheck the other boxes, and click Next. 4. Insert the driver CD, type in D:\2000, then click OK. (Change D: to match your CD-ROM drive letter) 5.
Summary of the content on the page No. 7
Windows Server 2003 1. At the Found New Hardware Wizard, choose Install from a list or specific location (Advanced), then click Next. 2. Insert the driver CD, check Include this location in the search, uncheck the other check box, type in D:\2003, and click Next. (Change D: to match your CD-ROM drive letter) 3. If the Hardware Installation window, click Continue Anyway, then Finish. Our driver has been tested for stability and compatibility. 4. Repeat steps 1-3 three more times. 5. Restart Wind
Summary of the content on the page No. 8
Changing COM Port Address Some serial devices need a specific COM port in order to work. If your serial device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Device Manager window double click Ports (COM & LPT), then double click the CyberSerial PCI serial port you want to change. 2. Click Settings tab, click the down arrow that is next to the Port Name box and select a COM address that is not currently in use. 3. Click OK, then close Device Manager to save the ch
Summary of the content on the page No. 9
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. A lifetime manufacturer warranty supplied with this product is offered by SIIG, Inc. Please see SIIG website for more
Summary of the content on the page No. 10
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by t
