Summary of the content on the page No. 1
Cyber 2S1P PCI
Quick Installation Guide
Introducing the Cyber 2S1P PCI
The Cyber 2S1P PCI high-speed serial I/O card provides
two 9-pin serial ports and one parallel port.
Features and Benefits
• Conforms to PCI v2.2 Plug and Play
• Full support for Windows-based software
• Reduces CPU load and improves system
performance dramatically
• IRQ sharing feature reduces IRQ conflicts
• High-speed serial port (9-pin) works with 56K V.90
external modems, ISDN terminal adapters, PDAs,
digital cameras, la
Summary of the content on the page No. 2
Package Contents • Cyber 2S1P PCI board • Connector bracket w/9-pin serial port • Driver CD • Quick Installation Guide Layout Serial Port 2 JP1 (S2) (S1) Pin 1 Serial Port 1 (S1) Parallel Port JP2 (S2) Figure 1. Layout Jumper Settings (JP1, JP2) Open = 0 volts (default) Short 1-2 = 5V Short 2-3 = 12V Note: Most serial devices do not require additional power through the serial port. Refer to your serial device's manual for more information. The jumper can be removed if the ports do not requir
Summary of the content on the page No. 3
Serial Port 2 Connection Stripe Figure 2. Connecting the ribbon cable Hardware Installation General instructions for installing the card are provided below, since the design of computer cases and motherboards vary. Refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. Avoid any contact with internal
Summary of the content on the page No. 4
5. Change JP1-JP2 jumper settings to the desired voltage only if your serial device(s) needs additional power from the serial port. However, most serial devices do not require additional power. For more information, see Figure 1 on page 2. Skip this step if power is not required. 6. If you need the second serial port, connect the 9-pin ribbon cable connector now. See Figure 2 on page 3 for more details. Skip this step if you only need one serial port. 7. To install the card, carefully align
Summary of the content on the page No. 5
Windows 98/98SE 1. At the Add New Hardware Wizard, click Next. 2. Select Search for the best driver for your device (Recommended), then click Next. 3. Insert the driver CD, check Specify a location, uncheck the other boxes, type in D:\9x, click Next. (Change D: to match your CD-ROM drive letter) 4. Click Next, then Finish. 5. Repeat steps 1-4. 6. Restart Windows to complete the installation. Windows ME 1. At the Add New Hardware Wizard, select Specify the location of the driver (Advanced), click
Summary of the content on the page No. 6
Windows NT 4.0 1. From the desktop click Start, then Run. 2. Insert the driver CD, type in D:\NT4\Install_Serial.exe, then click OK. (Change D: to match your CD-ROM drive letter) 3. Click Next when the Welcome window appears. 4. Choose Install, then click Next. 5. Click Yes, then click Exit. 6. From the desktop click Start, then Run. 7. Type in D:\NT4\Install_Parallel.exe, then click OK. (Change D: to match your CD-ROM drive letter) 8. Repeat steps 3-5. 9. Click Yes to restart Windows to compl
Summary of the content on the page No. 7
4. Insert the driver CD, type in D:\2000, then click OK. (Change D: to match your CD-ROM drive letter) 5. Click Next and Finish. 6. Repeat steps 1-5 two more times. 7. Restart Windows to complete the installation. Windows XP 1. At the Found New Hardware Wizard, choose Install from a list or specific location (Advanced), then click Next. 2. Insert the driver CD, check Include this location in the search, uncheck the other check box, type in D:\XP, and click Next. (Change D: to match your CD-ROM
Summary of the content on the page No. 8
4. Repeat steps 1-3 three more times. 5. Restart Windows to complete the installation. To Verify Windows 2000/XP/Server 2003 Installation 1. Right click My Computer, click Manage, then select Device Manager. 2. Double click Ports (COM & LPT), two CyberSerial PCI 16Cxxx... and one CyberParallel PCI... should be displayed. 3. Double click Multifunction adapters, SIIG CyberPro 2S1P PCI board should be displayed. Changing COM Port Address Some serial devices need a specific COM port in order to work
Summary of the content on the page No. 9
2. Click Settings tab and click Advanced. 3. Click the down arrow that is next to the COM Port number box and select a COM port that is not in use. Click OK. 4. Click OK, then close Device Manager to save the changes. Follow steps 1-4 again to change the second serial port if needed. Changing Parallel Port Address (LPT) Some parallel devices need a specific parallel port in order to work. If your parallel device works properly, do not change this setting. Windows 95/98/98SE/ME 1. From the Devi
Summary of the content on the page No. 10
Blank Page 10
Summary of the content on the page No. 11
Technical Support and Warranty QUESTIONS? SIIG’s Online Support has answers! Simply visit our website at www.siig.com and click on Support. Our online support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away. You can also submit questions online and one of our technical support analysts will promptly respond. A lifetime manufacturer warranty supplied with this product is offered by SIIG, Inc. Please see SIIG website for more
Summary of the content on the page No. 12
About SIIG, Inc. Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI & ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), Networking, Sound Cards, and other accessories. SIIG is the premier one-stop source of upgrades. SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive manufacturer warranty. High-quality control standards are evident by t
