Summary of the content on the page No. 1
ID-00210-000
Enclosure Installation Guide
37U Cabinet (37”DP / 42”DP)
42U Cabinet (37”DP / 42”DP)
45U Cabinet (37”DP / 42”DP)
Figure 1
42U X 42” DP Shown
ID-00210-000 REV D, ECO2773 Page 1 of 46
Proprietary Information of SharkRack, Inc.
32920 Alvarado-Niles Rd Suite 250, Union City, CA 94587
510-477-7900 • 510-324-1664 • www.sharkrack.com
Summary of the content on the page No. 2
SharkRack Enclosure Installation Guide Table of Contents Table of Contents ...................................................................................................................... 2 Introduction................................................................................................................................ 3 Symbols in Text ......................................................................................................................... 4 Important Sa
Summary of the content on the page No. 3
SharkRack Enclosure Installation Guide Introduction Thank you for buying a SharkRack computer cabinet. The SharkRack family of computer cabinets has been designed with great care and made with the highest quality materials to provide you with many years of satisfactory use. The SharkRack cabinet provides a top of the line cabinet with features that make installation, management, and ongoing maintenance fast, easy, and safe. We sincerely hope you enjoy using your SharkRack cabinet and we
Summary of the content on the page No. 4
SharkRack Enclosure Installation Guide Symbols in Text WARNING: Text set off in this manner indicates that failure to follow directions in the warning could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. Note: Text set off in this manner presents commentary, sidelights, or interesting points of information. Important Safety No
Summary of the content on the page No. 5
SharkRack Enclosure Installation Guide WARNING (CONT.): Plug cabinet power cords into electrical outlets that are located near the cabinet and are easily accessible. Connect all devices installed in a rack to power devices installed in the same cabinet. Do not plug into a power device installed in a different cabinet. Check the equipment power rating before plugging into a cabinet power device. Check that both the voltage range and current draw are within the limitations of the power devi
Summary of the content on the page No. 6
SharkRack Enclosure Installation Guide Chapter 1 Site Preparation Check Facility Provisions Ensure that the following conditions are met: • Floor is level and of sufficient strength to support the rack and your equipment. At 2 maximum gross weight, the floor must be able to support 1000 lb/in . • A qualified professional should complete site electrical power supply set-up. Ensure the types of outlets are consistent with the type of plugs on the power devices to be used. • Check wit
Summary of the content on the page No. 7
SharkRack Enclosure Installation Guide Rack Cabinet Footprint and Mounting Locations for: Cabinet with Full Rear and Front Doors Rear Door Front Door Figure 3 42U X 37DP (TOP VIEW) and 42U X 42DP (BOTTOM VIEW) Shown Table 1 Cabinet Dimensions DIM 37” CABINET 42” CABINET 45” CABINET A 86” 91” 82” B 41” 46” 49” C 37” 42” 45” D 35” 40” 43” Leveling Feet E 38” or 40” 43” or 45” 46” or 48” Floor mounting brackets ID-00210-000 REV D, ECO2773 Page 7 of 46
Summary of the content on the page No. 8
SharkRack Enclosure Installation Guide Rack Cabinet Footprint and Mounting Locations for: Cabinet with Split Rear Door Rear Doors Front Door Figure 4 42U X 37DP (TOP VIEW) and 42U X 42DP (BOTTOM VIEW) Shown Table 2 Cabinet Dimensions DIM 37” CABINET 42” CABINET 45” CABINET A 74” 79” 82” B 41” 46” 49” C 37” 42” 45” D 35” 40” 43” Leveling Feet E 38” or 40” 43” or 45” 46” or 48” Floor mounting brackets ID-00210-000 REV D, ECO2773 Page 8 of 46
Summary of the content on the page No. 9
SharkRack Enclosure Installation Guide Chapter 2 Receiving and Unpacking Check package and receiving area • Verify contents and condition. • Move the packaged cabinet on its pallet as close to its final destination as possible. • Be sure there is enough room to unload the cabinet from its packaging. In front of the pallet, it requires at least 7 feet for standard packaging (with or without pallet) and 13 feet for integration (crate) packaging to unload the cabinet. • Many SharkRack c
Summary of the content on the page No. 10
SharkRack Enclosure Installation Guide Unpacking Instructions- Standard Packaging Step Detail Note: Unpacking of a cabinet requires at least two people. There must be at least 7 feet of clear area in front of the loaded pallet to unload the cabinet. 1. Unwrap packaging material from around the cabinet Figure 5 42U X 42in DP Shown 2. Remove the (4) bolts securing the front Floor Mounting Bracket to the pallet and cabinet. 3. Repeat Step 2 for the rear Floor Mounting Br
Summary of the content on the page No. 11
SharkRack Enclosure Installation Guide Step Detail CAUTION: Be sure the leveling feet are fully raised to prevent accidental tipping. Figure 7 View of Caster and Leveling Foot 4. With one person on each side of the enclosure, carefully roll it toward the rear of the pallet until the rear casters clear the back edge of the pallet. Continue to slide the enclosure rearward until the rear casters make contact with the floor. 5. While one person carefully tips the enclosure slightl
Summary of the content on the page No. 12
SharkRack Enclosure Installation Guide Unpacking Instructions- Integration Packaging Step Detail WARNING: A fully loaded cabinet is very heavy. Take proper precautions when moving the cabinet Note: Unpacking of a cabinet requires at least two people. There must be at least 13 feet of clear area in front of the loaded crate to unload the cabinet. 1. Open the Crate. Loosen the (6) clips securing the front of the crate. The front of the crate is used as a ramp to unload th
Summary of the content on the page No. 13
SharkRack Enclosure Installation Guide Unpacking Instructions- Integration Packaging (cont.) Step Detail CAUTION: Be sure the leveling feet are fully raised to prevent accidental tipping. (See Figure 7 for details.) 5. With one person on each side of the enclosure, carefully roll it out of the wooden crate. 6. Unwrap packing material from around the cabinet. (Optional) Store all packing materials in a safe place for future use. Figure 11 Shipping Crate with 42U X 37DP Cabine
Summary of the content on the page No. 14
SharkRack Enclosure Installation Guide Chapter 3 Configure Accessories into the Cabinet Configure Optional Accessories The SharkRack cabinet can be configured using multiple optional accessories. The configuration depends on your specific application and may vary from cabinet to cabinet. The following list of processes is organized to help guide you through the typical steps of configuring optional accessories. Since each configuration is different, some processes may be excluded. Als
Summary of the content on the page No. 15
SharkRack Enclosure Installation Guide Installing and Removing Doors Step Detail To remove doors: 1. Open the door. 2. Pull down on the spring- loaded hinge pin attached to the top of the door. #3 3. Move top of door away from enclosure and lift the bottom of door up from the cabinet and set aside. #2 Figure 12 42U X 37DP Shown ID-00210-000 REV D, ECO2773 Page 15 of 46
Summary of the content on the page No. 16
SharkRack Enclosure Installation Guide Installing and Removing Doors (cont.) Step Detail To install doors: 1. Align the lower door hinge pin with the hole in the bottom hinge bracket and slide the hinge pin into the hole. 2. Pull down the upper hinge pin. 3. Align the upper hinge pin with the hole in the upper hinge bracket and release the hinge pin into the hole. 4. Make sure the door opens and closes properly. CAUTION: Ensure that hinge pins are secured into the hinge bracke
Summary of the content on the page No. 17
SharkRack Enclosure Installation Guide Door Handles Step Detail Remove door handle: To enhance your cabinet, SharkRack offers an optional line of electronic door handles which use HID or keypad entry. These locks can be networked together for remote management and access tracking. To install follow the CAM steps. 1. Open the door. 2. Rotate the handle to align the cam pointing down. 3. Use a screwdriver to push the snaps inward. Lift the handle off the door. 4. Install new d
Summary of the content on the page No. 18
SharkRack Enclosure Installation Guide How to Reverse the Door Swing Step Detail Reverse the door handle: 1. Open the door. 2. Rotate the handle to align the cam pointing down. 3. Use a screwdriver to push the snaps inward. Lift the handle off the door. CAM 4. Remove the cam screw securing the cam and rotate the cam 180°. Re-secure with the cam screw. 5. Rotate the door handle assembly 180° and reinstall it. Figure 15 Snap-In Handle and Lock ID-00210-000 REV D, ECO27
Summary of the content on the page No. 19
SharkRack Enclosure Installation Guide Step Detail Reverse the door hinge brackets: 4. Remove the door. (See “Installing and Removing Doors” on page 15) 5. Use a Phillips head screwdriver to remove the hinge pin brackets and latch bracket(s) from the cabinet frame. Figure 16 42U X 37DP Shown ID-00210-000 REV D, ECO2773 Page 19 of 46
Summary of the content on the page No. 20
SharkRack Enclosure Installation Guide How to Reverse the Door Swing (cont.) Step Detail 6. Reinstall the hinge pin brackets and latch bracket(s) on the opposite side of the cabinet. 7. Reinstall the door. CAUTION: Ensure that the door and its hinge pins are secured into the hinge brackets after the door is reinstalled. Figure 17 42U X 37DP Shown ID-00210-000 REV D, ECO2773 Page 20 of 46
