Summary of the content on the page No. 1
User’s Manual
IE-780338-NS-EM1
Emulation Board
Target Devices
µµµµ PD780318 Subseries
µµµµ PD780328 Subseries
µµµµ PD780338 Subseries
Document No. U16214EJ1V0UM00 (1st edition)
Date Published August 2002 N CP(K)
© 2002 1991
Printed in Japan
Summary of the content on the page No. 2
[MEMO] 2 User’s Manual U16214EJ1V0UM
Summary of the content on the page No. 3
Windows is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. PC/AT is a trademark of International Business Machines Corporation. • The information in this document is current as of May, 2002. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products
Summary of the content on the page No. 4
Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, pIease contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: • Device availability • Ordering information • Product release schedule • Availability of related technical literature • Development environment specifications (for example, specifications for third-party tools and
Summary of the content on the page No. 5
INTRODUCTION Product Overview The IE-780338-NS-EM1 is designed to be used with the IE-78K0-NS or IE-78K0-NS-A to debug the following target devices that belong to the 78K/0 Series of 8-bit single-chip microcontrollers. • µ PD780318 Subseries: µ PD780316, 780318 • µ PD780328 Subseries: µ PD780326, 780328 • µ PD780338 Subseries: µ PD780336, 780338, 78F0338 Target Readers This manual is intended for engineers who will use the IE-780338-NS-EM1 with the IE- 78K0-NS or IE-78K0-NS-A to perform system d
Summary of the content on the page No. 6
Terminology The meanings of certain terms used in this manual are listed below. Term Meaning Emulation device This is a general term that refers to the device in the emulator that is used to emulate the target device. It includes the emulation CPU. Emulation CPU This is the CPU block in the emulator that is used to execute user-generated programs. Target device This is the device that is the target for emulation. Target system This includes the target program and the hardware provided by the us
Summary of the content on the page No. 7
CONTENTS CHAPTER 1 GENERAL............................................................................................................................10 1.1 System Configuration................................................................................................................................ 11 1.2 Hardware Configuration ............................................................................................................................ 13 1.3 Basic Specifications.........
Summary of the content on the page No. 8
LIST OF FIGURES Figure No. Title Page 1-1 System Configuration ....................................................................................................................................... 11 1-2 Basic Hardware Configuration (Using IE-78K0-NS) ......................................................................................... 13 1-3 Basic Hardware Configuration (Using IE-78K0-NS-A)...................................................................................... 13 2-1 IE
Summary of the content on the page No. 9
LIST OF TABLES Table No. Title Page 1-1 Correspondence Between Emulation Probe and Conversion Connectors........................................................12 1-2 Basic Specifications ..........................................................................................................................................14 3-1 Main System Clock Settings..............................................................................................................................23 3-2 Sub
Summary of the content on the page No. 10
CHAPTER 1 GENERAL The IE-780338-NS-EM1 is a development tool for efficient debugging of hardware or software when using one of the following target devices that belong to the 78K/0 Series of 8-bit single-chip microcontrollers. This chapter describes the IE-780338-NS-EM1’s system configuration and basic specifications. • Target devices • µ PD780318 Subseries • µ PD780328 Subseries • µ PD780338 Subseries 10 User’s Manual U16214EJ1V0UM
Summary of the content on the page No. 11
CHAPTER 1 GENERAL 1.1 System Configuration Figure 1-1 illustrates the IE-780338-NS-EM1’s system configuration. Figure 1-1. System Configuration Debugger Note 1 Device file ID78K0-NS (available separately) (sold separately) Control software Host machine PC-9800 series TM or IBM PC/AT or compatibles Interface board Interface board Interface board IE-70000-98-IF-C IE-70000-PC-IF-C IE-70000-PCI-IF-A (sold separately) (sold separately) (sold separately) Interface card or Interface cable Interfa
Summary of the content on the page No. 12
CHAPTER 1 GENERAL Notes 1. The device file is as follows. µ S××××DF780338: µ PD780318, 780328, 780338 Subseries The device file can be downloaded from the web site of NEC Electron Devices (http://www.ic.nec.co.jp/micro/). 2. The emulation probe SWEX-120SE-1 and conversion connectors NQPACK120SE, YQPACK120SE, and YQ-GUIDE are products of TOKYO ELETECH CORPORATION. For further information, contact Daimaru Kogyo, Ltd. Tokyo Electronics Department (TEL: +81-3-3820-7112) Osaka Electronics Departme
Summary of the content on the page No. 13
CHAPTER 1 GENERAL 1.2 Hardware Configuration Figures 1-2 and 1-3 show the IE-780338-NS-EM1’s position in the basic hardware configuration. Figure 1-2. Basic Hardware Configuration (Using IE-78K0-NS) Dedicated bus interface IE system IE-78K0-NS IE-780338-NS-EM1 Interface board Emulation board 78K0 main board Host machine (sold separately) (this product) Interface card (sold separately) Emulation probe (sold separately) Figure 1-3. Basic Hardware Configuration (Using IE-78K0-NS-A) IE syste
Summary of the content on the page No. 14
CHAPTER 1 GENERAL 1.3 Basic Specifications The IE-780338-NS-EM1’s basic specifications are listed in Table 1-2. Table 1-2. Basic Specifications Parameter Description Target device µ PD780318, 780328, 780338 Subseries System clock 10.0 MHz Main system clock supply External: Clock input from the target system via an emulation probe Internal: Clock mounted on the emulation board (10.0 MHz) or mounted on the parts board by the user Subsystem clock supply External: Input from the target system v
Summary of the content on the page No. 15
CHAPTER 2 PART NAMES This chapter introduces the parts of the IE-780338-NS-EM1 main unit. The packing box contains the emulation board (IE-780338-NS-EM1), FG cable, packing list, user’s manual, and guarantee card. If there are any missing or damaged items, please contact an NEC sales representative. Fill out and return the guarantee card that comes with the main unit. 15 User’s Manual U16214EJ1V0UM
Summary of the content on the page No. 16
CHAPTER 2 PART NAMES 2.1 Parts of Main Unit Figure 2-1. IE-780338-NS-EM1 Part Names EXTOUT External trigger EXTIN Probe connector CN5 120GC LCD mask option LCD MOPT USER VDD Main system clock UMCLK Subsystem clock USCLK 16 User’s Manual U16214EJ1V0UM IC2 X2 X1 CN5 LED1
Summary of the content on the page No. 17
CHAPTER 3 INSTALLATION This chapter describes methods for connecting the IE-780338-NS-EM1 to the IE-78K0-NS or IE-78K0-NS-A, emulation probe, etc. Mode setting methods are also described. Caution Connecting or removing components to or from the target system, or making switch or other setting changes must be carried out after the power supply to both the IE system and the target system has been switched OFF. 17 User’s Manual U16214EJ1V0UM
Summary of the content on the page No. 18
CHAPTER 3 INSTALLATION 3.1 Connection (1) Connection with IE-78K0-NS or IE-78K0-NS-A main unit See the IE-78K0-NS User’s Manual (U13731E) for a description of how to connect the IE-780338-NS-EM1 to the IE-78K0-NS. See the IE-78K0-NS-A User’s Manual (U14889E) for a description of how to connect the IE-780338-NS-EM1 to the IE-78K0-NS-A. (2) Connection with emulation probe The following shows how to connect the emulation probe to the IE-780338-NS-EM1. On this board, connect the emulation probe S
Summary of the content on the page No. 19
CHAPTER 3 INSTALLATION <2> Connect the emulation probe SWEX-120SE-1 to CN5 of the IE-780338-NS-EM1. Figure 3-2. Emulation Probe Connection Emulation probe SWEX-120SE-1 (sold separately) CN5 FG cable (supplied with IE-780338-NS-EM1) Emulation board Main board of IE-78K0-NS (sold separately) IE-780338-NS-EM1 or IE-78K0-NS-A (sold separately) <3> Unfasten one of the screws on the metal board on the probe side of the IE-78K0-NS or IE-78K0-NS-A and connect and screw on the tip of the FG cable. Fi
Summary of the content on the page No. 20
CHAPTER 3 INSTALLATION 3.2 Clock Settings 3.2.1 Overview of clock settings The main system and subsystem clocks to be used during debugging can be selected from (1) to (3) below. (1) Clock that is already mounted on emulation board (2) Clock that is mounted by user (3) External clock If the target system includes an internal clock, select either (1) Clock that is already mounted on emulation board or (2) Clock that is mounted by user. For an internal clock, a resonator is connected to the ta
