Summary of the content on the page No. 1
PrPMC800/800ET Processor PMC
Module
Installation and Use
PRPMC800A/IH5
June 2006 Edition
Summary of the content on the page No. 2
© Copyright 2001, 2002, 2003, 2006 Motorola, Inc. All Rights Reserved. Printed in the United States of America. Motorola and the Motorola symbol are registered trademarks of Motorola, Inc. CompactPCI is a registered trademark of PCI Industrial Computer Manufacturers Group. All other products mentioned in this document are trademarks or registered trademarks of their respective holders.
Summary of the content on the page No. 3
Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this equipment. Failure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injury or damage to the equipment. The safety precautions listed below represent warnings of certain dangers of which Motorola is aware. You, as the user of the product, should follow these warnings and all other safety precautions neces
Summary of the content on the page No. 4
To prevent serious injury or death from dangerous voltages, use extreme caution when handling, testing, and adjusting this equipment and its Warning components. Flammability All Motorola PWBs (printed wiring boards) are manufactured with a flammability rating of 94V- 0 by UL-recognized manufacturers. EMI Caution This equipment generates, uses and can radiate electromagnetic energy. It ! may cause or be susceptible to electromagnetic interference (EMI) if not installed and used with adequat
Summary of the content on the page No. 5
Notice While reasonable efforts have been made to assure the accuracy of this document, Motorola, Inc. assumes no liability resulting from any omissions in this document, or from the use of the information obtained therein. Motorola reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Motorola to notify any person of such revision or changes. Electronic versions of this material may be read online, downloaded for perso
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Contents About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv 1 Preparation and Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 PrPMC800/800ET Description . . . . . . .
Summary of the content on the page No. 8
Contents ECC Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Onboard SDRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 SROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 10BaseT/100BaseTX Ethernet Channel . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 9
Contents 6 Modifying the Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 CNFG – Configure Board Information Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 ENV – Set Environment . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
Contents x PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)
Summary of the content on the page No. 11
List of Figures Figure 1-1. PrPMC800/800ET Headers, Connectors and Components . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 1-2. Installing a PrPMC800/800ET on a VMEmodule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2-3. PrPMC800/800ET Debug Serial Port Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 3-1. PrPMC800/800ET Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure
Summary of the content on the page No. 12
List of Figures xii PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)
Summary of the content on the page No. 13
List of Tables Table 2-1. PrPMC800/800ET Models/Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Table 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii Table 1-3. Start-Up Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Table 1-4. J2 Harrier Power-Up Configuration Header Pin Assignm
Summary of the content on the page No. 14
List of Tables xiv PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)
Summary of the content on the page No. 15
About This Manual PrPMC800/800ET Processor PMC Module Installation and Use provides information for installation and configuration of the PrPMC800/800ET, including jumper settings and installation procedures. It also includes descriptions of various components’ functions, connector pinout information, and a general description of the PPCBug firmware used with the board. ™ Information in this manual applies to Motorola boards that are compatible with the PowerPC instruction set architectur
Summary of the content on the page No. 16
About This Manual Table 2-1. PrPMC800/800ET Models/Configurations (continued) Model Number Processor / L2 Memory Ethernet PCI Bus PrPMC800 Speed Cache Speed PrPMC800-5279 MPC750 Class/ 1MB 512MB Rear 33 MHz 450 MHz PrPMC800-1259 MPC7410/ 2MB 128MB Rear 33 MHz 450 MHz PrPMC800-1269 MPC7410/ 2MB 256MB Rear 33 MHz 450 MHz PrPMC800-1279 MPC7410/ 2MB 512MB Rear 33 MHz 450 MHz PrPMC800-1251 MPC7410/ 2MB 128MB Front 33 MHz 450 MHz PrPMC800-2251 MPC7410/ 2MB 128MB None 66 MHz 450 MHz Capable PrPMC800
Summary of the content on the page No. 17
About This Manual Summary of Changes The following changes have been made to this manual. Table 2-2. Date Doc. Rev. Changes 6/2006 PRPMC800A/IH5 Updated Model and Configuration Table per EOL product list. 9/2003 PRPMC800A/IH4 Updates include processor core frequencies, Ethernet chip to include 82551IT, board temperature specifications. New model numbers were added to the Models/Configurations table to reflect the availability of industrial temperature board configurations. 01/2002 PRPMC
Summary of the content on the page No. 18
About This Manual Overview of Contents Chapter 1, Preparation and Installation, provides a general description of the PrPMC800/800ET including a summary of the basic features and architecture. It also includes a brief discussion of the monarch and non-monarch use of this board, and the carrier board requirements when the PrPMC800/800ET is being used as a monarch. The remainder of the chapter includes an overview of the start-up procedures, general information on unpacking and hardware pre
Summary of the content on the page No. 19
About This Manual Conventions Used in This Manual The following typographical conventions are used in this document: bold is used for user input that you type just as it appears. Bold is also used for commands, options and arguments to commands, and names of programs, directories and files. italic is used for names of variables to which you assign values. Italic is also used for comments in screen displays and examples, and to introduce new terms. courier is used for system output (for examp
Summary of the content on the page No. 20
About This Manual The MPU on the board is programmed to big-endian byte ordering. Any attempt to use little- endian byte ordering will immediately render the debugger unusable. Al Not l re eferences to processor bus support via the Harrier ASIC relate specifically to the MPC60x-class bus mode. They do not imply support of any other PowerPC-architecture bus mode. xx PrPMC800/800ET Processor PMC Module Installation and Use (PrPMC800A/IH5)
