Summary of the content on the page No. 1
INTEL 865 Main board
User’s Manual
Chapter 1 Package Contents
Your main board package contains the following items:
• One Intel 865 serial main board
• One 80-pin ultra DMA 66/100 IDE drive ribbon cable
• One 34- pin Floppy drive ribbon cable
• Software install CD
• One user’s manual
Chapter 2 Introduction
Key Features:
-Chipset:
Intel 865GV MCH: Intel 865GV: ICH: Intel 8280 IEB
-CPU:
Supports Intel Pentium HT (Hyper Threading Technology) CPU
Supports Intel Pentium 4 (
Summary of the content on the page No. 2
-One PS/2 mouse port -One GAME/MIDI port -One VGA port -One IRDA port -Two SATA ports -Sound onboard AC’97 2.2 specification compliant Supports six channel sound input (example Realtek ALC650) Supports 16 bit ADC (Analog Digital Converter) Supports multiple stereo input mixer Provides Mic In Line In Line Out jack -Built-in 10/100 Mbps LAN card (Optional) -Expansion slot: One 4X/8X AGP slot (supports 1.5V only) Two 32-bit PCI slots 2.2 specifications c
Summary of the content on the page No. 3
9 AuJF_L_Out 10 L_Out Back SATA: PIN Jumper setting PIN SATA Function PIN SATA2 Function 1 Ground 1 Ground 2 RSATA_RXP1 2 RSATA_RXP2 3 RSATA_RXNI 3 RSATA_RXN2 4 Ground 4 Ground 5 RSATA_TXP1 5 RSATA_TXP2 6 RSATA_TXP1 6 RSATA_TXP2 7 Ground 7 Ground Expansion slot DDR1/DDR2 184PIN DDR MEMORY SLOT PCI1/PCI2 32 PIN PCI BUS expansion slots AGP8X AGP display expansion slots Socket 775 Socket 775 CPU slots USB: Expansion Connector PIN Function PIN Function 1 VCC: Power 2 VCC: Pow
Summary of the content on the page No. 4
IDE1/IDE2 Primary/ Secondary IDE port SATA1/SATA2 SATA Port FDD Floppy Disk Drive Connector port PW1/PW2 ATX Power Supply Connector Port nd CPU FAN/2 FAN CPU/ System FAN port WOL Wake-on-Lan Connector port IRDA Irda Infrared port Function port panel Power Supply LED Pin 1: Power Supply Anode; Pin3: Ground HDD LED Pin2: power supply Anode; Pin: LED Signal Power Supply Switch Pin8 10: Switch Signal Reset Switch Pin4 16: Reset Switch Speaker Output Pin9: Speaker Output; Pin15: Power S
Summary of the content on the page No. 5
1. Push the latches on each side of the DIMM slot down. 2. Align the memory module with the slot. The DIMM slots are keyed with notches and the DIMMs are keyed with cutouts so that they. Can only be installed correctly. 3. Check that the cutouts on the DDIMM module edge connector match the notches in the DIMM slot. 4. Install the DIMM module into the slot and press it firmly down Until it seats correctly. The slot latches levered upwards and latch on to the edges of the DIMM. 5. Install
Summary of the content on the page No. 6
any Lan signal automatically resumes the system. You must enable this item using the power management page of the setup utility. 4.6.5 Clear CMOS (Clear RTC RAM) (Jp6) This jumper allows you to clear the Real Time clock (RTC) RAM in CMOS. You can clear the CMOS memory of data, time, and system setup parameters by crasing the CMOS RTC RAM data. The RAM data in CMOS that include system setup information such as system passwords is powered by the onboard button cell battery. 1. Turn OFF t
Summary of the content on the page No. 7
Windows NT4.0 LAN\8100 RTL8100 Lan driver setup Windows 9X Before installing audio driver, you must identify the mode of AC’97 codec. Fox example: if you use Realtek serial codec, you need to enter into the Realtek directory installing. 1.2 Intel Chipset software setup Insert the driver CD, running driver software CD, choose the directory: \CDROM:\INTEL\INF\ Click “NEXT” to continue Select “YES” to continue Select “NEXT” to continue Select “FINISH” to complete the installation. 1.
Summary of the content on the page No. 8
Select “Finish” to continue 1.7 LAN driver setup RTL8100 LAN driver only supports Windows 9x, Windows 2000/XP already built in this driver. Chapter 6 BIOS Setup The BIOS Setup utility record settings and information of your computer, such as date and time, the type of hardware installed, and various configuration settings your computer applies those information to initialize all the components when booting up and basic function. You components when booting up and basic function
Summary of the content on the page No. 9
6.3 Advance BIOS Features CPU L1&L2 Cache Leave these items enabled since all the processors that can be installed on this board have internal L2 cache memory First Boot Device when system boot-strap first time detect decive Second/ third boot device when system boot-strap first time detect device Boot other Device if you enable this item the system will also search for other boot devices if it fails to find an operating system from the first two locations. Swap floppy drive if yo
Summary of the content on the page No. 10
Setup select paralled port Default: 378/IRQ7 Paralled Port Mode Setup paralled port mode Default: SPP Game/Midi port Address Setup game/MIDI port address Default: 201/330 Midi Port IRQ Setup MIDI port IRQ Default: 10 6.6 Power Management Setup ACPI Function Setup if use ACPI function Default: Enabled Video off Method Setup video off method Default: DPMS Video off In Suspend Setup when video off in suspend Default: yes Suspend Type Setup suspends type Defau
Summary of the content on the page No. 11
If you highlight this item and press Enter, a dialog box appears that you can enter a supervisor password. You can enter no more than six letters or numbers. Press Enter after you have typed in the password. There will be the second dialog box asking you to retype the password for confirmation. Press Enter after you have retyped it correctly. Then the password is required for the access to the setup utility or for it at start-up, depending on the setting of the password check item in advanc
