Summary of the content on the page No. 1
How To Use This Manual ATC6430M Mainboard
HOW TO USE THIS MANUAL
This manual is written in a user-friendly style. It would be
advisable for users to read it in an orderly sequence :
1. For Hardware Information:
Read COMPONENT LOCATION DIAGRAM, Page A: QUICK JUMPER &
CONNECTOR SETTING, Page B: Slot 1 and CPU Installation, Page C:
CONNECTORS AND JUMPERS DESCRIPTION and Page D:List of Packaging.
2. For Mainboard and System Features:
Read “Chapter 1
Summary of the content on the page No. 2
ATC6430M Mainboard Contents CONTENTS QUICK JUMPER & CONNECTOR SETTING..........................A SLOT 1 AND PENTIUM II/III INSTALLATION...................B CONNECTORS AND JUMPERS DESCRIPTION....................C CHECKLIST OF PACKAGING................................................D HOW TO USE THIS MANUAL TABLE OF CONTENTS CHAPTER 1 System Features......................................................1 1-1 Introduction...........
Summary of the content on the page No. 3
Contents ATC6430 Mainboard 3-2-5 Power Management Setup......................................................................27 3-2-6 PNP/PCI Configuration..........................................................................31 3-2-7 PC Health Status ...................................................................................33 3-2-8 Frequency / Voltage Control...................................................................34
Summary of the content on the page No. 4
ATC6430M Mainboard Chapter 1 System Features CHAPTER 1 System Features 1-1 Introduction 6430M mainboard is designed to run with Intel 810 chipset to enhance the TM performance and extraordinary value of the Intel Celeron processor-powered PC. On the other hand, it is mounted with both Slot 1 and Socket 370 connector for users to make their CPU choice. It supports 66MHz, 100MHz and 133MHz Host TM Bus Intel PPGA Celeron CPUs. To enhance its peripheral s
Summary of the content on the page No. 5
Chapter 1 System Features ATC 6430M Mainboard 1-2 System Specifications of 6430M Mainboard : CPU Support: u Single CPU, with both Slot 1 and PPGA Socket 370 on board for choice. u Supports CPU Clock 66MHz, 100MHz and 133MHz (133MHz support “Slot 1” socket only). CPU Clock Ratios from 3.0x to 8.0x (step 0.5x). u Supports CPUs : Pentium II 233MHz~450MHz, Celeron 300MHz~500MHz, and Pentium III 450MHz~650MHz. u CPU Core Vol
Summary of the content on the page No. 6
ATC6430M Mainboard Chapter 1 System Features : BIOS Support: u Built-in VGA BIOS in Intel 810; and built-in Keyboard BIOS;. u AWARD BIOS in Intel 810, providing CMOS Setup Utilities: - Standard CMOS Features Setup for Date, Drives and VGA ; - Advanced BIOS Features Setup for CPU Cache, Self Test, Boot Device, Typematic Rate , and Security Options etc.; - Advanced Chipset Features Setup for SDRAM CAS, RAS, System BIOS Cacheable, and Video BIOS Cacheable
Summary of the content on the page No. 7
Chapter 1 System Features ATC 6430M Mainboard 1-3 Features Highlight 1-3-1 Add-on Features for VGA in Intel 810: : Integrated Graphics Controller u 3D Hyper Pipelined Architecture. u Full 2D H/W Acceleration. u Motion Video Acceleration. : 3D Graphics Visual Enhancements u Flat & Gouraud Shading. u Mip Maps with Bilinear and Anisotropic Filtering. u Fogging Atmospheric Effects. u Z Buffering. u 3D Pipe 2D Clipping.
Summary of the content on the page No. 8
ATC6430M Mainboard Chapter 1 System Features 1-3-3 AMR and AC’97 CODEC Controller AMR slot and AC’97 CODEC are integrated into the Mainboard to enable audio and modem playback. AMR (Audio/Modem Riser) slot is mounted on board to connect riser board with Audio and/or Modem CODEC (AMC/AC/MC Adapters). The AMR specification developed by Intel provides a mechanism for AC’97 codes to be on a riser card. To enable the onboard AC’97 CODEC, set JP9 pin 2-3 c
Summary of the content on the page No. 9
Chapter 1 System Features ATC 6430M Mainboard 1-3-5 Modem Ring On With Modem Ring On function, the computer can wake up by remote signal through a connected modem. This function enables users to access their computer data from anywhere in the world. Users have to enable “Power On by Ring” in “Power Management Setup” of the AWARD BIOS setup screens. 1-3-6 SB-Link Sideband Signals In order to migrate the
Summary of the content on the page No. 10
ATC6430M Mainboard Chapter 1 System Features 1-3-7 Ultra DMA 66 Cable (optional) Ultra DMA 66 cable (40-pin connector & 80-line cable) is packaged while utilizing FW82801AA chip which supports both UDMA 33 & UDMA 66 on the mainboard. In other words, Ultra DMA 33 cable is only used with FW82801AB chip And the Ultra DMA 66 color coded connectors are shown as bellow: Blue to Mainboard Grey to Slave Black to IDE Peripheral Master
Summary of the content on the page No. 11
Chapter 1 System Features ATC 6430M Mainboard Function” enabled through “ Power Management Setup” from the BIOS setup screen. Caution: For Wake-On-LAN, the +5V standby line for the power supply should be capable of delivering +5V ± 5% at 720mA. Failure to provide adequate standby current when implementing Wake-On-LAN will damage the power supply. WOL connector 8
Summary of the content on the page No. 12
6430M Mainboard Chapter 2 Installation CHAPTER 2 INSTALLATION 2-1 INSTALLATION PROCEDURE Before installing the computer, please prepare all components such as CPU, DRAM; peripherals such as hard drive, keyboard, CD-ROM and accessories such as cables. Then, install the system as following: TM - Put CPU / heat sink (refer to Celeron CPU installation guide or see the following setup chapter), and DRAM modules on the mainboard. - Plug add-on c
Summary of the content on the page No. 13
Chapter 2 Installation 6430M Mainboard 2-2 CPU INSTALLATION This mainboard supports PPGA Socket 370 and Slot 1 processors. The 6430M mainboard has built-in Switching Voltage Regulator to support CPU Vcore autodetection. That is, It is smart enough to detect and recognize the CPU voltage, clock, ratio and enables users to set up the CPU frequency from the BIOS Setup Screen. Users can adjust the frequency through “Frequency / Voltage Control” of the BIOS Setup
Summary of the content on the page No. 14
6430M Mainboard Chapter 2 Installation 2-3 SYSTEM MEMORY INSTALLATION 6430M mainboard provides two 3.3V 168-pin DIMM sockets for system memory expansion from 8MB to 512MB SDRAM. These two DIMMs are arranged to two banks, please refer to page A. Bank/DIMM PC-100 Memory Module Total Memory Bank0/DIMM1 8/16/32/64/128/256MB 8MB~256MB Bank1/DIMM2 8/16/32/64/128/256MB 8MB~256MB Total System Memory 8MB~512MB DIMM type, Size, pari
Summary of the content on the page No. 15
Chapter 2 Installation 6430M Mainboard 2-4 INTEL 810 DRIVER INSTALLATION ØØ INF Files for Windows 95/98 : 1. Start Windows 95/98. 2. Put the All-In-One CD into your CD-ROM drive. 3. Choose Intel 810/820 Inf Files on the Autorun main menu. 4. Then follow the instruction on the screen. (INF Files that enable the Intel 810/820 Chipsets to be recognized by listed operating systems.) 2-5 VGA DRIVER INSTALLATION Install Intel 810 AGP Driver For Win95/98/NT
Summary of the content on the page No. 16
ATC6430M Mainboard Chapter 3 Award BIOS Setup CHAPTER 3 AWARD BIOS SETUP Award BIOS manufacturer provides access to the system BIOS through the hardware and software on mainboard. The hardware consists of a Flash ROM (4MB in 6430M mainboard) and the software is a group of programs that are installed in the ROMBIOS along with all the other data that should be included into the BIOS. After the BIOS is updated, if you want to clear the old setup data stored
Summary of the content on the page No. 17
Chapter 3 Award BIOS Setup ATC6430M Mainboard 3-1 UPDATE BIOS PROCEDURE 3-1-1 BIOS Update: If the BIOS needs to be updated, you can get a CD with the updated BIOS utility in the package. The CD includes : “awdflash.exe” -- BIOS update utility program “awdflash.doc” The update procedure is as following: 1. Boot the system to DOS mode in a normal manner. 2. Insert the updated CD to drive D (or E). 3. Change working directory to CD-ROM drive, D or E, which
Summary of the content on the page No. 18
ATC6430M Mainboard Chapter 3 Award BIOS Setup 3-1-2 UPDATE MICROCODE API Intel also provides MICROCODE API (Applications Programming Interface) for mainboard user to update data block in BIOS quickly and easily. (You can find this utility in the All-In-One CD in the mainboard package). The BIOS code on the mainboards contains data that is specific to each silicon stepping of the processor. Integrators must ensure that this BIOS stepping data matc
Summary of the content on the page No. 19
Chapter 3 Award BIOS Setup ATC6430M Mainboard 3-2 SYSTEM BIOS CONFIGURATION SETUP The following pages explain how to set up the BIOS configuration under the Award BIOS. The SETUP program is stored in the Read-Only-Memory (ROM) on the mainboard. To do the SETUP procedure, press the key when the system is booting up. The following main menu will appear. Please select " STANDARD CMOS FEATURE" to enter the next screen. CMOS Setup Utility - Copyright (
Summary of the content on the page No. 20
ATC6430M Mainboard Chapter 3 Award BIOS Setup Control Key Description UP ARROW Move to the previous item DOWN ARROW Move to the next item LEFT ARROW Move to the item on the left RIGHT ARROW Move to the item on the right Esc KEY Esc Main Menu : Quit without saving changes Setup menu : Exit current page and return to main menu PgUp KEY Increase the numeric value or make changes PgDn KEY Decrease the numeric value or make changes F1 KEY Help G
