Summary of the content on the page No. 1
PRIMERGY
System Board D2530
for Econel 200 S2
Technical Manual
Susanne Däschlein
Fujitsu SiemensComputers GmbH München
81730 München
e-mail: email: manuals@fujitsu-siemens.com
Tel.: (089) 61001-155
Fax: (++49) 700 / 372 00000
D2530 (Econel 200 S2)
Sprachen: En
Edition November 2006
Summary of the content on the page No. 2
Comments… Suggestions… Corrections… The User Documentation Department would like to know your opinion of this manual. Your feedback helps us optimize our documentation to suit your individual needs. Fax forms for sending us your comments are included in the back of the manual. There you will also find the addresses of the relevant User Documentation Department. Certified documentation according to DIN EN ISO 9001:2000 To ensure a consistently high quality standard and user-friendliness, this d
Summary of the content on the page No. 3
Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2 Important notes . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.1 Notes on safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2.2 CE Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2.3 Environmental Protection . . . . . . . . . . . . . . . . . . . 11 3 Feat
Summary of the content on the page No. 4
Summary of the content on the page No. 5
1Introduction This technical manual describes the system board D2530, which can be ® equipped with one or two Intel processors. Further information about drivers is provided in the readme files on the hard disk, on the supplied "ServerSupport" or "ServerStart" CDs. You will find further information in the BIOS description. Notational conventions The meanings of the symbols and fonts used in this manual are as follows: italics indicates commands, menu items, file and path names or software pro
Summary of the content on the page No. 6
Summary of the content on the page No. 7
2 Important notes In this chapter you will find essential information regarding safety when working with your server. V CAUTION! With the system board installed you must open the system to access the system board. How to access the system board of your system is described in the appropriate service supplement. When handling the system board, refer to the specific notes on safety in the operating manual and/or service supplement for the respective server. 2.1 Notes on safety V CAUTION! The
Summary of the content on the page No. 8
Notes on safety Important notes V Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. There is a danger of burns! Transmisson lines to peripheral devices must be adequately shielded. To the LAN wiring the requirements apply in accordance with the standards EN 50173 and EN 50174-1/2. As minimum requirement the use of a protected LAN line of category 5 for 10/100 MBps Ethernet, and/or of category 5e for Gigabit
Summary of the content on the page No. 9
Important notes Notes on safety Modules with electrostatic-sensitive components Systems and components that might be damaged by electrostatic discharge (ESD) are marked with the following label: Figure 1: ESD label When you handle components fitted with ESDs, you must observe the following points under all circumstances: You must always discharge yourself of static charges (e.g. by touching a grounded object) before working. The equipment and tools you use must be free of static charges.
Summary of the content on the page No. 10
CE Certificate Important notes Notes about boards During installation/deinstallation of the system board, observe the specific instructions described in the service manual for the server. Remove the plug from the mains outlet so that system and system board are totally disconnected from the mains voltage. To prevent damage to the system board, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards ar
Summary of the content on the page No. 11
Important notes Environmental Protection 2.3 Environmental Protection Environmentally friendly product design and development This product has been designed in accordance with standards for ”environmen- tally friendly product design and development“. This means that the designers have taken into account important criteria such as durability, selection of materials and coding, emissions, packaging, the ease with which the product can be dismantled and the extent to which it can be recycled. Th
Summary of the content on the page No. 12
Environmental Protection Important notes Returning, recycling and disposal The device may not be disposed of with household rubbish. This appliance is labelled in accordance with European Directive 2002/96/EC concerning used electrical and electronic appliances (waste electrical and electronic equipment - WEEE). The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU. To return your used device, please use the return and collect
Summary of the content on the page No. 13
Features Overview 3 Features 3.1 Overview Processors ® – 2 x Intel Xeon™ Dual Core processors ® – 2 processor sockets Dual LGA771 for Intel Xeon™ Dual Core processor with 1333/1066/667 MHz front side bus ® – supports Intel Extended Memory 64 Technology (EM64T) ® – supports Intel Hyper-Threading Technology (H.T.), except: 5100 series Main memory – 4 slots for main memory FBD533/PC2-4200F Fully Buffered DIMM memory modules with 512 MB, 1Gbyte and 2Gbyte – maximum 8 Gbyte of memory – minimum 512
Summary of the content on the page No. 14
Overview Features Internal connectors – floppy disk – 1 IDE primary – 6 SATA connectors – SATA-HDD access (HDLED) – 2 USB connectors – 1 serial port connector (COM2) – PC98 connector – 1 parallel port connector (LPT1) – front panel – main power connector (12V, -12V, 5V, 3.3V and 5V auxiliary) – 12V (CPU) power connector – 2 CPU fans – 1 rear fan – BPSMB connector – BPSMB connector –RAID key External connectors – 1 serial port (COM1) – 2 PS/2 interfaces for keyboard and mouse – 2 USB 2.0 ports
Summary of the content on the page No. 15
Features Main memory 3.2 Main memory The system board supports up to 8 Gbyte main memory. 4 slots (2 banks with 2 modules) are available for the main memory. Each memory bank can be populated with 512 Mbyte, 1 Gbyte or 2 Gbyte FBD533/PC2-4200F Fully Buffered DIMM memory modules. ECC with memory scrubbing and with the Single Device Data Correction (SDDC) function is supported. I You will find the descriptions how to install memory modules in the Options Guide of your server. Module populatio
Summary of the content on the page No. 16
PCI bus Features 3.3 PCI bus slot 6 PCI-Express x16 slot 5 PCI-Express x8 slot 4 PCI 33MHz slot 3 PCI-X 133/100 MHz slot 2 PCI-X 133/100 MHz slot 1 PCI-X 133/100 MHz Figure 3: PCI slots PCI slots The following table shows an overview of the PCI slots: PCI slot 64Bit/ Frequency Description 32Bit in MHz 1 133/100 PCI-X bus slot, IOOP 2 133/100 PCI-X bus slot, IOOP 3 133/100 PCI-X bus slot, IOOP 4 32 Bit 33 PCI bus slot 5 PCI-Express x8 slot (x4 accessed) 6 PCI-Express x16 slot (x8 accessed) PCI IR
Summary of the content on the page No. 17
Features PCI bus The PCI interrupts INTA#, INTB#, INTC# and INTD# are available for each PCI slot (except the PCI-Express slots). The same interrupt can be assigned simultaneously to several PCI boards. You should avoid this condition due to reduced performance. If you use a setting other than Auto, the Plug&Play functionality of the system BIOS for the corresponding PCI boards is deactivated. Auto The PCI interrupts are assigned automatically in accordance with the Plug&Play guidelines. Di
Summary of the content on the page No. 18
Screen resolution Features 3.4 Screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the system board. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller. 1) Screen Possible refresh rates (Hz) Color depth resolution (bits pro pixel, bpp) 2) 2) 640x480 60, 72, 75, 85, 90, 100, 120, 160, 20
Summary of the content on the page No. 19
Features Temperature / system monitoring Fan control The fans are controlled according to temperature. Sensor monitoring The removal of, or a fault in, a temperature sensor is detected. Should this happen all fans monitored by this sensor run at maximum speed, to achieve the greatest possible protection of the hardware. Voltage monitoring The most important voltages are monitored. When a voltage exceeds warning level high or falls below warning level low an alert will be generated. Adequate
Summary of the content on the page No. 20
Connectors and jumpers Features 3.6 Connectors and jumpers 1 2 3 4 5 6 CPU 1 DIMM 2B DIMM 1B 27 DIMM 2A DIMM 1A CPU 2 26 25 24 PCI-E x16 7 23 Battery RAID PCI-E x8 8 key 22 PCI 33MHz PCI-X 133/100 MHz 9 PCI-X 133/100 MHz A PCI-X 133/100 MHz 21 20 19 18 17 16 15 14 13 12 11 10 Figure 4: Schematic overview of the system board D2530 1 = KBPWR (jumper) 15 = USBPW 3/4 (jumper) 2 = USBPW 1/2 (jumper) 16 = USB 3/4 3 = power supply ATX 17 = BPSMB 4 = PC98 18 = floppy disk 5 = power supply12V (CPU1,
