Summary of the content on the page No. 1
MF599-06
-
CMOS 4 BIT SINGLE CHIP MICROCOMPUTER
S1C62 Family
Development Tool Reference Manual
Summary of the content on the page No. 2
NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice. Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level re
Summary of the content on the page No. 3
S1C62 Family Development Tool Reference Manual Preface The explanation covering the outline and operation of the development support tools for the CMOS 4-bit Single Chip Microcomputer S1C62 Family has been divided into the following parts. I. INTRODUCTION II. DEVELOPMENT TOOL MANAGEMENT SYSTEM DMS6200 III. CROSS ASSEMBLER ASM62XX IV. MELODY ASSEMBLER MLA628X V. FUNCTION OPTION GENERATOR FOG62XX VI. SEGMENT OPTION GENERATOR SOG62XX VII. EVALUATION BOARD S5U1C62XXXE VIII. ICE CONTROL SOFTWARE ICS6
Summary of the content on the page No. 4
Summary of the content on the page No. 5
The information of the product number change Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative. Configuration of product number Devices S1 C 60N01 F 0A01 00 Packing specification Specification Package (D: die form; F: QFP) Model number Model name (C: microcomputer, digital products) Product classification (S1: semiconductor) Developme
Summary of the content on the page No. 6
Summary of the content on the page No. 7
I S1C62 FAMILY DEVELOPMENT TOOL INTRODUCTION This part explains the composition of the develop- ment support tool for the 4-bit Single Chip Micro- computer S1C62 Family and the developmental environment.
Summary of the content on the page No. 8
Summary of the content on the page No. 9
INTRODUCTION INTRODUCTION Contents 1 TYPES OF DEVELOPMENT SUPPORT TOOLS ____________________ I-1 1.1 Composition of the Software Development Tools S5U1C62xxxD...........................I-1 1.2 Composition of the Hardware Tools .......................................................................I-1 2 DEVELOPMENTAL ENVIRONMENT_____________________________ I-2 3 DEVELOPMENT FLOW ________________________________________ I-2 4 INSTALLATION _______________________________________________ I-4 5 DIFF
Summary of the content on the page No. 10
Summary of the content on the page No. 11
INTRODUCTION 1 TYPES OF DEVELOPMENT SUPPORT TOOLS Here we will explain the composition of the software and hardware for the development support tools. 1.1 Composition of the Software Development Tools S5U1C62xxxD The below software are included in the software development support tools used in each S1C62XXX model. 1. Development Tool Management System DMS6200 .. Menu selections for each software / start-up software 2. Cross Assembler ASM62XX ...................................... Cross assembler
Summary of the content on the page No. 12
INTRODUCTION 2 DEVELOPMENTAL ENVIRONMENT The software product of the development support tool S5U1C62xxxD operates on the following host systems: • IBM PC/AT (at least PC-DOS Ver. 2.0) When developing the S1C62XXX, the above-mentioned host computer, editor, P-ROM writer, printer, etc. must be prepared by the user in addition to the development tool which is normally supported by Seiko Epson. S1C62xxx Development Tool Host computer Software tools (IBM PC/AT) S5U1C62000A S5U1C62xxxD DMS6200 SOG62x
Summary of the content on the page No. 13
INTRODUCTION *1, *2 *1 Determination of Determination of software specifications hardware specifications *2, *3, *4 *4, *5 *4, *5 *4, *5 *1, *6 Flow chart generation Melody generation Function option list Segment option list Creation of and coding and coding generation generation target board *4, *5 Development support tool Function Segment Coding Coding selection on menu of option option sheet sheet Development Tool list list Management System DMS6200 Source file generation Source file generat
Summary of the content on the page No. 14
INTRODUCTION 4 INSTALLATION The S5U1C62xxxD tools are included on the CD-ROM of the S5U1C62000A (S1C60/62 Family Assembler Package), and they can be installed in your hard disk using the installer (Setup.exe) on the CD-ROM. Refer to the "S5U1C62000A Manual" for how to install the S5U1C62xxxD tools. Note The DMS6200 configures a menu from files that are located in the current directory. Therefore, do not move the development tools from the directory in which the DMS6200 exists. To invoke an edito
Summary of the content on the page No. 15
INTRODUCTION 5 DIFFERENCES FROM MODEL TO MODEL AND PRECAUTIONS There may be some models in which the following two types software tools contained in the S5U1C62xxxD are not included. (1) Segment Option Generator SOG62XX This is not included in the software tools of models in which the segment option has not been set. (2) Melody Assembler MLA628X This is not included in the software tools for the models (Other than S1C62N8X) that do not have the melody function. Please be aware of the following p
Summary of the content on the page No. 16
INTRODUCTION 6 TROUBLESHOOTING Tool Problem Remedy measures ICE Nothing appears on the screen, or Check the following and remedy if necessary: S5U1C62000H nothing works, after activation. • Is the RS-232C cable connected correctly? • Is the RS-232C driver installed? • Is MODE.COM on the disk? • Is the execution file correct? PC-DOS ICS62XXW.EXE • Is the DOS version correct? PC-DOS Ver. 2.1 or later • Is the DIP switches that set the baud rate of the main ICE unit set correctly? • Is the fuse of
Summary of the content on the page No. 17
INTRODUCTION Tool Problem Remedy measures ASM62XX An R error occurs although the final The cross assembler is designed to output "R error" every page is passed. time the page is changed. Use a pseudo-instruction to set the memory, such as ORG or PAGE, to change the page. See "Memory setting pseudo-instructions" in the cross assem- bler manual. MDC62XX Activation is impossible. Check the following and remedy if necessary: • Is the number of files set at ten or more in OS environ- ment file CONFIG
Summary of the content on the page No. 18
Summary of the content on the page No. 19
II DEVELOPMENT TOOL MANAGEMENT SYSTEM DMS6200 This part mainly explains how to operate the De- velopment Tool Management System DMS6200.
Summary of the content on the page No. 20
