Summary of the content on the page No. 1
P4M800 Pro-M7
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications
Summary of the content on the page No. 2
Table of Contents Chapter 1: Introduction .............................................................. 1 1.1 Features.............................................................................................. 1 1.2 Package List....................................................................................... 3 1.3 Layout ................................................................................................ 4 Chapter 2: Hardware Installation ............................
Summary of the content on the page No. 3
P4M800 Pro-M7 CHAPTER 1: INTRODUCTION 1.1 FEATURES CPU Supports LGA 775. Supports Intel Pentium 4 processor up to 3.8GHz. Supports Dual Core CPU. Front side bus at the following frequency ranges: - 400MHz (100MHz Core Clock) - 533MHz (133MHz Core Clock) - 800MHz (200MHz Core Clock) - 1066MHz (266MHz Core Clock) Supports Hyper-Threading Technology. WARNING! Warranty will be void if the pin protection cap is not in place to protect the socket pin when sending this mainboard f
Summary of the content on the page No. 4
P4M800 Pro-M7 Super I/O Chip: ITE IT8705AF Provides the most commonly used legacy super I/O functionality. Environment Control initiatives: - H/W Monitor. - Fan Speed Controller. - ITE “Smart Guardian” function. On Board IDE Support 4 IDE disk drives. Supports PIO Mode 0~4. Supports Ultra DMA 33/66/100/133 Bus Master Mode. 10/100 LAN PHY PHY: RealTek RTL8201BL/RTL8201CL. Supports 10/100 Mb/s auto-negotiation operation. Half/Full duplex capability. Supports ACPI, PCI po
Summary of the content on the page No. 5
P4M800 Pro-M7 Front Side Onboard Peripherals 1 front panel header supports front panel facilities. 1 S/PDIF out connector supports digital audio out function. 1 CD-in connector supports 1 CD-ROM audio-in device. 1 front audio header supports front panel audio function. 1 chassis open header supports PC case-opened warning function. 1 Floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes. 2 USB headers support 4 USB 2.0 ports. 2 IDE connectors support 4 hard
Summary of the content on the page No. 6
JPRNT1 JVGA1 JCOM1 P4M800 Pro-M7 1.3 LAYOUT JKBMS1 JCFAN1 JATXPWR2 LGA775 CPU1 JUSB1 JUSBV1 P4M800 Pro JUSBLAN1 Super I/O JAUDIO1 BIOS AGP1 LAN BAT1 PCI1 JUSB2 JFAUDIO1 VT8237R JSATA2 PCI2 JUSB3 PLUS JCDIN1 JAUX1 JSATA1 JSPDIFO1 JUSBV2 (optional) PCI3 JCMOS1 JSFAN1 JPANEL1 JCI1 Codec CNR1 FDD1 st Note: ■ represents the 1 pin. 4 DDR2_A2 DDR2_A1 IDE1 IDE2 JATXPWR1
Summary of the content on the page No. 7
P4M800 Pro-M7 CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU) Special Notice: Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin legs won’t be damaged. Pin Cap Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle. 5
Summary of the content on the page No. 8
P4M800 Pro-M7 Step 2: Look for the triangular cut edge on socket, and the golden dot on CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation. Step 2-1: Step 2-2: Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation. Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the JCFAN1. This completes the
Summary of the content on the page No. 9
P4M800 Pro-M7 2.2 FAN HEADERS These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1. JCFAN1: CPU Fan Header Pin Assignment 4 1 Ground 2 Power (+12V) 3 FAN RPM rate sense 1 4 Smart Fan Control JSFAN1: System Fan Header Pin Assignment 1 Ground 2 Power (+12V) 3 1 3 FAN RPM rate sense Note:
Summary of the content on the page No. 10
P4M800 Pro-M7 2.3 INSTALLING SYSTEM MEMORY 1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot. 2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated. 8 DDR2_A1
Summary of the content on the page No. 11
P4M800 Pro-M7 2.4 CONNECTORS AND SLOTS FDD1: Floppy Disk Connector FDD1: Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables. 2 34 33 1 IID DE E1 1//IID DE E2 2: : H Ha ar rd d D Diis sk k C Co on nn ne ec ct to or rs s The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ult
Summary of the content on the page No. 12
P4M800 Pro-M7 PCI1~PCI3: Peripheral Component Interconnect Slots PCI1~PCI3: Peripheral Component Interconnect Slots This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits. PCI1 PCI2 PCI3 A AG GP P1 1: : A Ac cc ce elle er ra at te ed d G Gr ra ap ph hiic cs s P Po or rt t S Sllo ot t Your monitor will attach directly to that video card. This mot
Summary of the content on the page No. 13
P4M800 Pro-M7 CNR1: Communication Network Riser Slot CNR1: Communication Network Riser Slot The CNR specification is an open Industry Standard Architecture, and it defines a hardware scalable riser card interface, which supports modem only. CNR1 11
Summary of the content on the page No. 14
P4M800 Pro-M7 CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”. Pin opened Pin closed Pin1-2 closed 3.2 DETAIL SETTINGS JUSBV1/JUSBV2: Power Source Headers for USB ports Pin 1-2 Close: JUSBV1: +5V for USB ports at JUSB1 and JUSBLAN1. JUSBV2: +5V for USB ports at front panel (JUSB2/JUSB3). Pin 2-3 Close: JUSBV1: U
Summary of the content on the page No. 15
P4M800 Pro-M7 JATXPWR1: ATX Power Source Connector This connector allows user to connect 20-pin power connector on the ATX power supply. Pin Assignment 1 +3.3V 2 +3.3V 3 Ground 10 20 4 +5V 5 Ground 6 +5V 7 Ground 8 PW_OK 9 Standby Voltage +5V 10 +12V 11 +3.3V 12 -12V 111 13 Ground 14 PS_ON 15 Ground 16 Ground 17 Ground 18 -5V 19 +5V 20 +5V JATXPWR2: ATX Power Source Connector By connecting this connector, it will provide +12V to CPU power circuit. Pin Ass
Summary of the content on the page No. 16
P4M800 Pro-M7 JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel This header allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader. Pin Assignment 1 +5V (fused) 2 +5V (fused) 3 USB- 4 USB- 5 USB+ 6 USB+ 7 Ground JUSB2 8 Ground 2 10 9 Key 10 NC 1 9 JUSB3 JPANEL1: Front Panel Header This 24-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep button, speaker and IrDA Connec
Summary of the content on the page No. 17
P4M800 Pro-M7 JCDIN1: CD-ROM Audio-in Connector This connector allows user to connect the audio source from the variaty devices, like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.. Pin Assignment 1 Left Channel Input 2 Ground 3 Ground 4 Right Channel Input 4 1 JFAUDIO1: Front Panel Audio Header This header allows user to connect the front audio output cable with the PC front panel. It will disable the output on back panel audio connectors. Pin Assignment 1
Summary of the content on the page No. 18
P4M800 Pro-M7 JCMOS1: Clear CMOS Header By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard. 1 3 Pin 1-2 Close: Normal Operation (Default). 1 3 1 3 Pin 2-3 Close: Clear CMOS data. ※ ※ ※ ※ Clear CMOS Procedures: 1. Remove AC power line. 2. Set the jumper to “Pin 2-3 Close”. 3. Wait for five seconds. 4. Set the jumper to “Pin 1-2 Close”. 5. Power on
Summary of the content on the page No. 19
P4M800 Pro-M7 JSATA1~JSATA2: Serial ATA Connectors The motherboard has a PCI to SATA Controller with 2 channels SATA interface, it satisfies the SATA 1.0 spec and with transfer rate of 1.5GB/s. Pin Assignment 1 Ground 2 TX+ 3 TX- 4 Ground 71 4 5 RX- 6 RX+ 7 Ground JSATA1 1 4 7 JSPDIFO1: Digital Audio-out Connector This connector allows user to connect the PCI bracket SPDIF output header. Pin Assignment 1 +5V 2 SPDIF_OUT 3 Ground 31 17
Summary of the content on the page No. 20
P4M800 Pro-M7 CHAPTER 4: USEFUL HELP 4.1 AWARD BIOS BEEP CODE Beep Sound Meaning One long beep followed by two short Video card not found or video card beeps memory bad High-low siren sound CPU overheated System will shut down automatically One Short beep when system boot-up No error found during POST Long beeps every other second No DRAM detected or install 4.2 EXTRA INFORMATION A A.. B BIIO OS S U Up pd da at te e After you fail to update BIOS or BIOS is invaded by virus, the
