Apple Xserve 073-0691 user manual

User manual for the device Apple Xserve 073-0691

Device: Apple Xserve 073-0691
Category: Computer Hardware
Manufacturer: Apple
Size: 0.11 MB
Added : 3/5/2014
Number of pages: 6
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Apple Xserve 073-0691. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Apple Xserve 073-0691.

For your convenience

If looking through the Apple Xserve 073-0691 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Apple Xserve 073-0691 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Apple Xserve 073-0691 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Apple Xserve 073-0691 User manual - Online PDF
Advertisement
« Page 1 of 6 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Apple Xserve 073-0691 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Apple Xserve 073-0691. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 1


Xserve
Single-Slot Riser Card
Replacement Instructions
Follow the instructions in this sheet carefully. Failure to follow these instructions could
damage your equipment and void its warranty.
Note: Online instructions covering customer-installable parts are available at
http://www.info.apple.com/installparts/.
Tools Required
No tools are required for this procedure. You may, however, find a Phillips screwdriver
useful in releasing the thumbscrews at the front of the server.
O

Summary of the content on the page No. 2

4. If the server is in the locked position (the yellow security LED on the front panel is on), use the Allen key that came with the server to unlock it. 5. If the cable management arm is not in use, unplug all external cables except the power cord. 6. Touch the server’s metal case to discharge any static electricity. Important: Always ground yourself by touching the server’s case before you touch any parts or install any components inside the server. To avoid static electricity bu

Summary of the content on the page No. 3

9. Grasp the thumbscrews and slide the bottom housing forward part way to expose the two chassis levers. (Figure 2) 10. While depressing both levers, pull the bottom housing all the way forward and remove it from the rack. Figure 2 11. Place the bottom housing on a sturdy, flat surface and ESD mat. 12. Put on the ESD wrist strap. Xserve Single-Slot Riser Card - 3

Summary of the content on the page No. 4

Removing the Single-Slot Riser Card 1. Release the thumbscrew that secures the PCI or AGP card fence to the back of the server. (FIgure 3) Figure 3 2. Pull the clip on the riser forward to release the riser from the logic board connector. (Figure 4) 3. Disconnect the riser from the logic board and remove the riser and PCI or AGP card from the server. Figure 4 Xserve Single-Slot Riser Card - 4

Summary of the content on the page No. 5

4. Disconnect the PCI or AGP card from the riser. (Figure 5) Figure 5 Installing the Replacement Single-Slot Riser Card 1. Install the PCI or AGP card in the replacement riser card. 2. Reconnect the riser card to the logic board. 3. Tighten the thumbscrew that secures the PCI or AGP card fence to the back of the server. Closing the Server 1. Carefully slide the bottom housing back into the rack. 2. Tighten the front thumbscrews to secure it. Warning: Never turn on the server unless a

Summary of the content on the page No. 6

Apple Computer, Inc. © 2002 Apple Computer, Inc. All rights reserved. This document is protected under U.S. Copyright Law and International Treaties, and no part of this document may be reproduced in any form without written permission from Apple. Apple is not responsible for typographical, printing, or inadvertent errors. Apple Computer, Inc. 1 Infinite Loop Cupertino, CA 95014-2084 USA + 1 408 996 1010 http://www.apple.com Apple, the Apple logo, Mac, Macintosh, and the Mac logo are t


Alternative user manuals
# User manual Category Download
1 Apple EY5QGRAMKEEPER User manual Computer Hardware 0
2 Apple Drive Interconnect Board User manual Computer Hardware 0
3 Apple Sonic Blaster User manual Computer Hardware 0
4 Apple Memory (RAM) User manual Computer Hardware 0
5 Apple RamWorks 2 MEG Plus User manual Computer Hardware 0
6 Apple NVIDIA GEFORCE 7800 GT User manual Computer Hardware 5
7 Apple eMac ATI Graphics User manual Computer Hardware 4
8 Apple FireWire Cable User manual Computer Hardware 1
9 Apple Logic Board User manual Computer Hardware 0
10 Apple 073-0808 REV. C User manual Computer Hardware 1
11 Apple Memory DIMMs User manual Computer Hardware 0
12 Apple Sirius IIGS User manual Computer Hardware 0
13 Apple 073-0562 User manual Computer Hardware 1
14 Apple ATA Controller Board User manual Computer Hardware 0
15 Apple SDRAM DIMM User manual Computer Hardware 0
16 Sony MSAKIT-PC4A User manual Computer Hardware 2
17 Sony MRW62E-S1 2694866142 User manual Computer Hardware 5
18 Philips MATCH LINE 9596 User manual Computer Hardware 17
19 Sony 64GB SDHC Class 10 Memory Card Readers SF32UY User manual Computer Hardware 1
20 Philips PSC702 User manual Computer Hardware 1