Summary of the content on the page No. 1
IS7 Series
(IS7-G, IS7, IS7-E, IS7-E2, IS7-E2G,
IS7-E2V, IS7-M, IS7-V2)
Intel Pentium 4 System Board
Socket 478
User’s Manual
4200-0375-11
Rev. 1.06
Summary of the content on the page No. 2
Copyright and Warranty Notice The information in this document is subject to change without notice and does not represent a commitment on part of the vendor, who assumes no liability or responsibility for any errors that may appear in this manual. No warranty or representation, either expressed or implied, is made with respect to the quality, accuracy or fitness for any particular part of this document. In no event shall the manufacturer be liable for direct, indirect, special, inciden
Summary of the content on the page No. 3
Table Of Contents Chapter 1. Introduction .......................................................................... 1-1 1-1. Features & Specifications ........................................................................1-1 1-2. Layout Diagram (IS7-G/IS7/IS7-E).........................................................1-4 1-3. Layout Diagram (IS7-E2/IS7-E2G/IS7-E2V)..........................................1-5 1-4. Layout Diagram (IS7-M) .................................................
Summary of the content on the page No. 4
3-7. PnP/PCI Configurations.........................................................................3-22 3-8. PC Health Status ....................................................................................3-24 3-9. Load Fail-Safe Defaults .........................................................................3-25 3-10. Load Optimized Defaults .......................................................................3-25 3-11. Set Password ..............................................
Summary of the content on the page No. 5
Introduction 1-1 Chapter 1. Introduction 1-1. Features & Specifications 1. CPU Supports Intel Pentium 4 Socket 478 processor with 800MHz, 533MHz, and 400MHz (for Northwood only) System Data Bus Supports Intel Hyper-Threading Technology 2. Chipset Intel 82865PE (MCH) + 82801ER (ICH5R) (IS7-G/IS7) Intel 82865PE (MCH) + 82801EB (ICH5) (IS7-E/IS7-E2/IS7-E2G/IS7-E2V) Intel 82865G (MCH) + 82801EB (ICH5) (IS7-M) Intel 82848P (MCH) + 82801EB (ICH5) (IS7-V2) Supports Hi-Speed U
Summary of the content on the page No. 6
1-2 Chapter 1 9. Audio Onboard 6-Channel AC 97 CODEC Professional digital audio interface supports S/PDIF In/Out (IS7-G/IS7/IS7-E) 10. ABIT Engineered ™ ABIT SoftMenu Technology ™ ABIT EQ (IS7-G/IS7/IS7-E/IS7-E2/IS7-M/IS7-V2) ™ ABIT FANEQ (IS7-G/IS7/IS7-E/IS7-M/IS7-E2) ™ ABIT FlashMenu 11. Internal I/O Connectors 1x AGP slot 5x PCI slots 1x Floppy port supports up to 2.88MB 2x Ultra ATA/100/66/33 connectors 4x Serial ATA 150 connectors (IS7-G) 2x Serial ATA
Summary of the content on the page No. 7
Introduction 1-3 14. Order Information Model Chipset LAN SB SATA PCI SATA IEEE 1394 IS7-G 865PE + ICH5R 10/100/1000M RAID 0/1 RAID 0/1 3 Ports IS7 865PE + ICH5R 10/100M RAID 0/1 - 3 Ports IS7-E 865PE + ICH5 10/100M 2 Ports - - IS7-E2 865PE + ICH5 10/100M 2 Ports - - IS7-E2G 865PE + ICH5 10/100/1000M 2 Ports - - IS7-E2V 865PE + ICH5 - 2 Ports - - IS7-M 865G + ICH5 10/100M 2 Ports - - IS7-V2 848P + ICH5 10/100M 2 Ports - - Specifications and information contained herein are subjec
Summary of the content on the page No. 8
1-4 Chapter 1 1-2. Layout Diagram (IS7-G/IS7/IS7-E) IS7 Series
Summary of the content on the page No. 9
Introduction 1-5 1-3. Layout Diagram (IS7-E2/IS7-E2G/IS7-E2V) User’s Manual
Summary of the content on the page No. 10
1-6 Chapter 1 1-4. Layout Diagram (IS7-M) IS7 Series
Summary of the content on the page No. 11
Introduction 1-7 1-5. Layout Diagram (IS7-V2) User’s Manual
Summary of the content on the page No. 12
1-8 1-8 Chapter 1 Chapter 1 IS7 Series IS7 Series
Summary of the content on the page No. 13
Hardware Setup 2-1 Chapter 2. Hardware Setup Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do so may cause the motherboard components or add-on cards to malfunction or damaged. 2-1. Install The Motherboard Most computer chassis have a base with many mounting holes to allow motherboard to be securely attached on and at the same time, pr
Summary of the content on the page No. 14
2-2 Chapter 2 ® 2-2. Install Pentium 4 CPU and Heatsink Supporting-Base This motherboard provides a ZIF (Zero Insertion ® ® Force) Socket 478 to install Intel Pentium 4 CPU. The CPU you bought should have a kit of heatsink and cooling fan along with. If that’s not ® the case, buy one specially designed for Pentium 4 Socket 478. 1. Locate the 478-pin ZIF socket on the motherboard. Fasten the Retention Module Base onto the motherboard. ATTENTION: If you are using chassis specially ® de
Summary of the content on the page No. 15
Hardware Setup 2-3 2-3. Install System Memory IS7-G/IS7/IS7-E/IS7-M: This motherboard provides four 184-pin DDR DIMM slots for Single/Dual Channel DDR 400/333/266 memory modules with memory expansion size up to 4GB. To reach the performance of Dual Channel DDR, the following rules must be obeyed: When installing TWO DIMM modules: Install DIMM modules of the same type and size for slots [DIMM1]+[DIMM3] or slots [DIMM2]+[DIMM4]. When installing FOUR DIMM modules: Install DIMM modules
Summary of the content on the page No. 16
2-4 Chapter 2 IS7-E2/IS7-E2G/IS7-E2V/IS7-V2: This motherboard provides 2 184-pin DDR DIMM sites for memory expansion available from minimum 128MB to maximum 2GB. IS7-E2/IS7-E2G/IS7-E2V: IS7-V2: Bank Memory Module Total Memory Bank 0, 1 (DIMM1) 128, 256, 512MB, 1GB 128MB ~ 1GB Bank 2, 3 (DIMM2) 128, 256, 512MB, 1GB 128MB ~ 1GB Total System Memory 128MB ~ 2GB NOTE: No hardware or BIOS setup required after adding or removing memory modules. IS7 Series
Summary of the content on the page No. 17
Hardware Setup 2-5 Power off the computer and unplug the AC power cord before installing or removing memory modules. 1. Locate the DIMM slot on the board. 2. Hold two edges of the DIMM module carefully, keep away of touching its connectors. 3. Align the notch key on the module with the rib on the slot. 4. Firmly press the module into the slots until the ejector tabs at both sides of the slot automatically snaps into the mounting notch. Do not force the DIMM module in with extra force
Summary of the content on the page No. 18
2-6 Chapter 2 2-4. Connectors, Headers and Switches Here we will show you all of the connectors, headers and switches, and how to connect them. Please read the entire section for necessary information before attempting to finish all the hardware installation inside the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of connectors and headers on the board that you may refer to. WARNING: Always power off the computer and unplug the AC power cor
Summary of the content on the page No. 19
Hardware Setup 2-7 (2). FAN Power Connectors These 3-pin connectors each provide power to the cooling fans installed in your system. The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring the speed of the CPU fan. CPUFAN1: CPU Fan Power Connector NBFAN1: Chipset Fan Power Connector SYSFAN1: System Fan Power Connector AUXFAN1, AUXFAN2: Auxiliary Fan Power Connector WARNING: These fan connectors are not jumpers. DO NOT place jumper ca
Summary of the content on the page No. 20
2-8 Chapter 2 (3). CMOS Memory Clearing Header This header uses a jumper cap to clear the CMOS memory. Pin 1-2 shorted (default): Normal operation. Pin 2-3 shorted: Clear CMOS memory. IS7-G/IS7/IS7-E: IS7-M: IS7-E2/IS7-E2G/IS7-E2V: IS7-V2 WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS memory. Failing to do so may cause your system to work abnormally or malfunction. IS7 Series
