Summary of the content on the page No. 1
TOSHIBA AMERICA INFORMATION SYSTEMS
STORAGE DEVICE DIVISION
IRVINE, CALIFORNIA
SD-M1712
DVD-ROM DRIVE
USER MANUAL
Summary of the content on the page No. 2
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD-ROM Drive ......................................................6 Troubleshooting.......................................................................8 Specifications ..........................................................................9 Drive Connectors...................
Summary of the content on the page No. 3
INTRODUCTION – SD-M1712 DVD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD-ROM 85ms DVD 95ms DVD-RAM 170ms DAE (Digital Audio Extraction) Audio Capability MPC3 Compatibility Multi-Read Capability Regionalization (RPC2 compliance) (DVD) ATAPI BUS Interface Drive Speed DVD 16X Single Layer 10X Dual Layer CD 48X DVD-RAM 2X (ver 1.0) 2X (ver 2.1) Types of Disc Formats Sup
Summary of the content on the page No. 4
CD • CD-DA • CD+(E)G • CD-MIDI • CD-TEXT • CD-ROM • CD-ROM-XA • CD-I Bridge (Photo-CD, Video CD) • CD-I • Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) • CD-R (Read) • CD-RW (Read) Front Panel Figure 1.SD-M1712 DVD-ROM Drive Front Panel Load disc using tray. Loading Tray Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: • BUSY light goes out. T
Summary of the content on the page No. 5
SETUP – SD-M1712 DVD-ROM The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable (optional) • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD-ROM drive. By placing a jumper on the pins, you can select the following functions: CS Drive is configured using host interface signal CSEL SL Configures drive a
Summary of the content on the page No. 6
Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system. Your Toshiba DVD-ROM drive can be place
Summary of the content on the page No. 7
Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Toshiba's DVD-ROM drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the DVD-ROM drive (see DVD-ROM drive Back Panel photo for location). Refer to
Summary of the content on the page No. 8
USING THE DVD DVD-ROM Drive – SD-M1712 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close. Inserting a Disc - Vertically To insert a disc in a drive that is mounted vertic
Summary of the content on the page No. 9
Usage Guidelines • Keep the disc tray closed when not using the DVD-ROM Drive. • Do not press down on the disc tray when opening or closing it. • Do not place objects on the disc tray. • Never use a damaged, broken, or deformed disc. • Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc. To stop a DVD movie, click Stop button in the DVD player application program. NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has
Summary of the content on the page No. 10
TROUBLESHOOTING – SD-M1712 Problem Solution Disc tray cannot be opened • Check that there is power to drive. • Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables). • Are the drive configuration jumpers on the DVD-ROM drive set properly? • Is the software driver loaded? On a step-by-step (F8) Boot of the system is the DVD-ROM
Summary of the content on the page No. 11
SPECIFICATIONS –SD-M1712 General Interface ATAPI Compatible DVD-ROM Standards DVD DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R, DVD-RW, DVD-RAM CD CD-DA CD-ROM CD-I Bridge (Photo-CD, Video CD) Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-MINI CD-TEXT CD+(E)G CD-ROM-XA CD-I CD-R (Read) CD-RW (Read) Storage Capacities DVD 4.377GB (DVD-5) 7.959GB (DVD-9) 8.754GB (DVD-10) 15.917GB (DVD-18) 3.679GB (DVD-R, Ver. 1.0) 4.377GB (DVD-R, Ver. 2.0) 2.324GB (DVD-RAM, Ver 1.0
Summary of the content on the page No. 12
Performance Rotational Speed DVD-ROM (6.0X - 16X) single layer 9,200rpm (4.1X - 10X) dual layer 6,300rpm DVD-R (Ver 2.0), DVD-RW (2 - 4.8X) 2,780rpm DVD-R (Ver 1.0) (2 - 4.8X) 3,200rpm DVD-RAM (Ver 1.0) (2X) 2,160 - 4,800rpm DVD-RAM (Ver 2.1) (1X) 1,380 - 3,300rpm DVD-Video CSS-disc (2 - 4.8X) 2,780rpm CD-ROM, CD-R/RW(20.7 - 48X) 9,500rpm CD-DA Transfer (14 - 32X) 1,800 - 4,300rpm CD-DA/Video CD (4X - 7.8X) 1,200 - 2,000rpm Data Transfer Rate DVD (Single) 8,910 - 21,60
Summary of the content on the page No. 13
Spin-up Time DVD 1.5s Typ DVD-RAM (Ver 2.1) 1.5s Typ DVD-RAM (Ver 1.0) 1.9s Typ CD 1.4s Typ Data Buffer 192Kbytes Reliability MTBF 100,000 hours Power ON Hours 5,436 hours/year ON/OFF Cycles 313 cycles/yea Number of Access 600,000 accesses/year Operating Duty Cycle 20% of Power ON time (Reading/Seeking) MTTR 0.5 hours Audio Number of Channels 2 Frequency Response 20Hz to 20,000 Hz Distortion -80 dB (at 1kHz JIS A-weighted) Output Levels Head
Summary of the content on the page No. 14
Power DC Voltage and Current Requirements 5V 5%, 12V 5% +5V +12V Sleep 200mA 0mA Standby 240mA 0mA Idle 410mA (DVD) 50mA (DVD) 430mA (CD) 50mA (CD) Random Access (average) 660mA (DVD) 730mA (DVD) 600mA (CD) 830mA (CD) Physical Height 5.75" (146mm) Width 1.6" (41.5mm) Depth 7.6" (193mm) Weight 2.18lbs (.99kg) Connectors DC input AMP 1-480424-0 IDE Interface Connector 40 Pin ATAPI Standard Analog Audio Line Output Connector 4 Pin ATAPI Standard (70066 Series, C Versi
Summary of the content on the page No. 15
DRIVE CONNECTORS –SD-M1712 Figure 1.SD-M1712 DVD-ROM Drive Rear Panel - Connectors Power Power is supplied to your DVD-ROM drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has Connector chamfered edges, so the power connector fits only one way CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Audio Supplies Analog and Digital sound t
Summary of the content on the page No. 16
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN I/O SIGNAL HOST SIGNAL NAME PIN I/O SIGNAL HOST SIGNAL NAME NO. NAME NO. NAME 1 I Reset Host Reset 21 O HDRQ DMA Request 2 - GND 22 - GND 3 I/O HD7 Host Data Bus BIT 7 23 I HWR-,STOP Host I/O Write 4 I/O HD8 Host Data Bus BIT 8 24 - GND 5 I/O HD6 Host Data Bus BIT 6 25 I HRD-, Host I/O Read HDMARDY, - HSTROBE 6 I/O HD9 Host Data Bus BIT 9 26 - GND 7 I/O HD5 Host Data Bus BIT 5 27 O IORDY, I/O Channel Ready
