Summary of the content on the page No. 1
PRODUCT MANUAL
ST1.3 Series
ST612712DEG ST680712DEG
ST612712DE ST680712DE
ST610712DEG ST660712DEG
ST610712DE ST660712DE
Rev. C
February 2007
Summary of the content on the page No. 2
Revision status summary sheet Revision Date Sheets Affected Rev. A 07/13/2006 All. Rev. B 09/14/2006 1, 3, 5-7, 17, 20 and 26. Rev. C 02/27/2007 Front cover and 18 . Copyright © 2006 - 2007 Seagate Technology LLC. All rights reserved. Printed in U.S.A. Publication number: 100409345, Rev. C February 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. ST1.3 Series, SeaTools and SeaTDD are either tradem
Summary of the content on the page No. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2 Drive care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.3 Handling precautions. . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
ii ST1.3 Series Product Manual, Rev. C
Summary of the content on the page No. 5
List of Figures Figure 1. ST1.3 Series IDE interface (ZIF connector) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Figure 2. ST1.3 Series breather hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 3. ST1.3 Series improper handling example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Figure 4. Typical 3.3V startup and operation current profile . . . . . . . . . . . . .
Summary of the content on the page No. 6
iv ST1.3 Series Product Manual, Rev. C
Summary of the content on the page No. 7
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ST1.3 Series drives: • ST612712DE-12GB, ST610712DE-10GB, ST680712DE-8GB and ST660712DE-6GB disc drives with a ZIF (zero insertion force) connector using an IDE interface. • ST612712DEG-12GB, ST610712DEG-10GB, ST680712DEG-8GB and ST660712DEG-6GB disc drives with a ZIF (zero insertion force) connector using an IDE interface. These models incorporate an additional free-fall
Summary of the content on the page No. 8
1.1 Disclaimer Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non- infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specifi- cation or sample. Seagate may not be held liable for any direct, indirect, incidental, special, exemplary, or con- sequential damages (including, but not limited to, loss of use, data, or profits; procurement of substitute goods or services; or business interruptions
Summary of the content on the page No. 9
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST612712DE, ST612712DEG, ST610712DE, ST610712DEG, ST680712DE, ST680712DEG, ST660712DE and ST660712DEG model drives. 2.1 Power, access times and acoustics The specifications listed in this table are for quick reference. For details on specification measurement or def
Summary of the content on the page No. 10
Table 1: Specifications ST612712DEG ST610712DEG ST680712DEG ST660712DEG Drive specification ST612712DE ST610712DE ST680712DE ST660712DE Read/write power (typical 3.3V) 230/240 mA Performance idle mode (typical 3.3V) 140 mA Low power idle mode (typical 3.3V) 77 mA Standby/Sleep mode (typical 3.3V) 13 mA Voltage tolerance (including noise) 3.3V ± 5% Ambient temperature 0° to 60°C (operating) –40° to 70°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating
Summary of the content on the page No. 11
2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST612712DEG 12.0 Gbytes 23,438,016 512 ST612712DE ST610712DEG 10.0 Gbytes 19,533,924 512 ST610712DE ST680712DEG 8.0 Gbytes 15,625,008 512 ST680712DE ST660712DEG 6.0 Gbytes 11,719,008 512 ST660712DE 2.3 Default logical geometry Model Cylinders Read/write heads Sectors per track ST612712DEG ST612712DE ST610712DEG ST610712DE 16,383 16 63 ST680712DEG ST680712DE ST660712DEG ST660712DE LBA mode When addres
Summary of the content on the page No. 12
2.4 Recording and interface technology Technology Specification Interface Seagate (ZIF) Flex Connector (35-way) Recording method Perpendicular Magnetic Recording Recording density BPI (bits/inch max) 933,000 Track density TPI (tracks/inch max) 140,000 2 Areal density (Gbits/inch max) 130.6 Spindle speed (RPM) (± 0.2%) 3,600 Internal data-transfer rate OD (Mbits/sec max) 130.0 Sustained data transfer rate OD (Mbytes/sec max) 10.2 I/O data-transfer rate (Mbytes/sec max) 66.7 (UDMA 4) Interleave 1:
Summary of the content on the page No. 13
2.7 Power specifications The drive receives DC power (+3.3V) through the ZIF (IDE interface) connector for ST612712DE, ST612712DEG, ST610712DE, ST610712DEG, ST680712DEG, ST680712DE, ST660712DEG and ST660712DE models. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 8. Typical power measurements are based on an average of drives tested, under nominal conditions, using +3.3V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measur
Summary of the content on the page No. 14
Table 2: DC power ST1.3 Series Power Consumption (W) Average 3.3V (mA) Max 3.3V (mA) Max current the average of the peak value in 10ms window Current 270 330 Spinup 180 300 Load/Unload current 190 200 Write 240 300 Read 230 300 Seek 154 161 Performance idle 140 147 Low power idle 77 86 Standby/Sleep 13 18 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. 2.7.1.1 Typical current
Summary of the content on the page No. 15
2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +3.3 volt line. Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave injected noise at up to 20 MHz. Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write current. 2.7.3 Voltage tolerance Voltage tolerance (including noise): 3.3V ± 5% ST1.3 Series Product Manua
Summary of the content on the page No. 16
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. The drive features the following power-management modes: Table 3: Power-management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Enabled Idle, performance Tracking Rotating Enabled Idle, low power Parked Stopped Disabled Standby/Sleep Parked Stopped Disabled • Active mode The drive is in Active mode during the read/write and seek operations. • Low pow
Summary of the content on the page No. 17
2.8 Environmental specifications 2.8.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditions. Case temperature of the drive operating at 60°C ambient may hit a maximum of 70°C at certain parts of the casing. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 0° to 60°
Summary of the content on the page No. 18
2.8.5 Shock All shock measurements in this section are carried out at drive level. For all linear shock test, operating or non- operating, the input shock level shall be measured at the frame of the disk drive at the specific location indi- cated by the ellipse in Figure 5 below for the ZIF interface drives. Figure 5. Location where tri-axial accelerometer will be placed on ST1.3 Series drives All shock test will cover all the 6 directions, +/- x, y and z axes. The drive axis definition in shown
Summary of the content on the page No. 19
2.8.6.1 Operating sweep sine vibration The following lists the maximum operating sweep sine vibration levels that the drive may experience while meeting the performance standards specified. It will consist of a forward and backward sweep from 10 Hz to 500 Hz to 10 Hz. The drive will operate without a hard error while being subjected to the following vibration levels. 10 Hz to 500 Hz @ 2 oct/min 1.0 Gs (0 to pk). Maximum displacement may apply below 10 Hz. 2.8.6.2 Operating random vibration Th
Summary of the content on the page No. 20
2.8.6.4 Nonoperating random vibration The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in the table below. The vibration test level is 3.01 Gs RMS. The drive will not incur any physical damage when subsequently put into operation. Table 5: Nonoperating random vibration profile. 2 Frequency (Hz) G /Hz 2.5 1.0 x E-03 5 3.0 x E-02 40 1.8 x E-02 500 1.8 x E-02 2.8.6.5 Corrosive environment Seagate electronic drive components pass accelerat
