Summary of the content on the page No. 1
DB35 Series
ST3400832ACE
ST3300831ACE
ST3250823ACE
ST3200826ACE
Summary of the content on the page No. 2
Summary of the content on the page No. 3
DB35 Series ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE
Summary of the content on the page No. 4
©2005, Seagate Technology LLC All rights reserved Publication number: 100347671, Rev. B May 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trade- marks or trademarks of Seagate Technology LLC. Other product names are registered trade- marks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications. No part of this pu
Summary of the content on the page No. 5
Revision status summary sheet Revision Date Sheets Affected Rev. A 01/26/05 All. Rev. B 05/16/05 Pages 6 and 7. DB35 Series Product Manual, Rev. B iii
Summary of the content on the page No. 6
iv DB35 Series Product Manual, Rev. B
Summary of the content on the page No. 7
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 8
vi DB35 Series Product Manual, Rev. B
Summary of the content on the page No. 9
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 3. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 4. Master/slave jumper settings . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
viii DB35 Series Product Manual, Rev. B
Summary of the content on the page No. 11
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate DB35 model drives: DB35 Series ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE These drives provide the following key features: Minimal acoustics for consumer storage usage profile. Bedroom quiet performance. Optimized power for consumer storage devices. Spinup current limited to a maximum of 2 amps. 7,200-RPM spindle speed 8-Mbyte buffer on: ST340083
Summary of the content on the page No. 12
2 DB35 Series Product Manual, Rev. B
Summary of the content on the page No. 13
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST3400832ACE, ST3300831ACE, ST3250823ACE and ST3200826ACE model drives. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manu
Summary of the content on the page No. 14
Drive specification ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE Track-to-track seek time (msec typical) 0.8 (read), 1.0 (write) Average seek (msec typical) 18 (read), 20 (write) Startup current (typical) 12V (peak) 2.0 amps Seek power (typical) 8.6 watts Operating (Consumer Storage Profile) 7.2 watts Idle mode (typical) 6.9 watts Standby mode (typical) 0.80 watts Sleep mode (typical) 0.80 watts Voltage tolerance 5V ± 5% (including noise) 12V ± 10% Ambient 0° to 60°C (operating) tempera
Summary of the content on the page No. 15
2.2 Formatted capacity Formatted Guaranteed Model capacity sectors Bytes per sector ST3400832ACE 400 Gbytes 781,422,768 512 ST3300831ACE 300 Gbytes 586,072,368 512 ST3250823ACE 250 Gbytes 488,397,168 512 ST3200826ACE 200 Gbytes 390,721,968 512 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.1.2, "Identify Device command" (words 60-61 and 100-103) for
Summary of the content on the page No. 16
2.4 Physical characteristics Drive specification Maximum height (mm) 26.11 (inches) 1.028 Maximum width (mm) 101.85 (inches) 4.010 ± 0.010 Maximum length (mm) 146.99 (inches) 5.787 Typical weight (grams) 635 (pounds) 1.39 2.5 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: Track-to-track seek time is an average of all possible single-track seeks in
Summary of the content on the page No. 17
2.7 Power specifications The drive receives DC power (+5V and +12V) through a four-pin standard drive power connector. 2.7.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
Summary of the content on the page No. 18
2.7.1.1 Typical current profile Figure 1 Typical 5V startup and operation current profile Figure 2 Typical 12V startup and operation current profile 2.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. Us
Summary of the content on the page No. 19
2.7.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Power mode Heads Spindle Buffer Active Tracking Rotating Enabled Idle Tracking Rotating Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled Active mode The drive is in Active mode during the read/write and seek operations.
Summary of the content on the page No. 20
2.8.2 Temperature gradient Operating: 20°C per hour (68°F per hour max), without condensation Nonoperating: 30°C per hour (86°F per hour max) 2.8.3 Humidity 2.8.3.1 Relative humidity Operating: 5% to 90% noncondensing (30% per hour max) Nonoperating: 5% to 95% noncondensing (30% per hour max) 2.8.3.2 Wet bulb temperature Operating: 37.7°C (99.9°F max) Nonoperating: 40°C (104°F max) 2.8.4 Altitude Operating: –60.96 m to 3,048 m (–200 ft. to 10,000+ ft.) Nonoperating: –60.96 m to 12,192 m (–200 ft
