Summary of the content on the page No. 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ST310014ACE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ultra ATA Interface Drive
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Manual
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 2
Summary of the content on the page No. 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ST310014ACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Product Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
2002, 2003 Seagate Technology LLC All rights reserved Publication Number: 100216026, Rev. D, December, 2003 Seagate, Seagate Technology and the Seagate logo are trademarks or registered trademarks of Seagate Technology LLC. SeaShell is a trademark of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications. No part of this publication may be reproduced in an
Summary of the content on the page No. 5
ST310014ACE Product Manual, Rev. D iii Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1.1 Default logical geometry . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
iv ST310014ACE Product Manual, Rev. D 1.12.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . 15 2.1 Handling and static-discharge precautions . . . . . . . . . . . . . . 15 2.2 Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . 16 2.3 Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 2.3.1 Master/slave configuration .
Summary of the content on the page No. 7
ST310014ACE Product Manual, Rev. D v Figures Figure 1. Typical startup and operation current profile . . . . . . . . . . . . 7 Figure 2. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 3. Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . 19 Figure 5. I/O pins and supported ATA signals. . . . . . . . . . . . . . . . . . 21
Summary of the content on the page No. 8
vi ST310014ACE Product Manual, Rev. D
Summary of the content on the page No. 9
ST310014ACE Product Manual, Rev. D 1 Introduction This manual describes the functional, mechanical and interface specifi- cations for the ST310014ACE. This drive provides the following key features: • Low power consumption High instantaneous (burst) data-transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5 Giant magnetoresistive (GMR) recording heads and GPRML technol- ogy, which provide the drives with increased areal density State-of-the-art cache and on-the-fly error-c
Summary of the content on the page No. 10
2 ST310014ACE Product Manual, Rev. D Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual. Drive Specification ST310014ACE 6 Formatted Gbytes (×10 bytes) 10.0 Guaranteed sectors 20,005,650 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Physical read/write heads 1 Discs 1 Recording density BPI (bits/inc
Summary of the content on the page No. 11
ST310014ACE Product Manual, Rev. D 3 Drive Specification ST310014ACE Standby to ready (sec typical) 6.5 sec Spindown (sec typical) 10 sec Startup current (typical) 0.9 amps (5V), 1.9 amps (12V) Seek power (typical) 6.0 watts Read/Write power (typical) 5.5 watts Idle mode power (typical) 4.5 watts Standby mode power (typical) 1.2 watts Sleep mode (typical) 1.0 watts Voltage tolerance (including noise) 5V ± 5%, 12V ± 10% Ambient temperature 0° to 60°C (op.), –40° to 70°C (nonop.) Temperature gra
Summary of the content on the page No. 12
4 ST310014ACE Product Manual, Rev. D 1.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the ST310014ACE. 1.1 Formatted capacity Drive Model Formatted Gbytes Guaranteed Bytes per sectors sector ST310014ACE 10.0 20,005,650 512 1.1.1 Default logical geometry CHS Mode Cylinders Read/Write Sectors per heads track
Summary of the content on the page No. 13
ST310014ACE Product Manual, Rev. D 5 I/O data-transfer rate 16.6 (PIO mode 4) (Mbytes/sec max) 100 (Ultra DMA mode 5) Interleave 1:1 Cache buffer (Mbytes) 2 1.4 Physical characteristics Drive Specification ST310014ACE Maximum height mm (inches) 19.99 (0.787) Maximum width mm (inches) 101.9 (4.01) Maximum length mm (inches) 147.0 (5.78) Typical weight grams (pounds) 455 (1.0) 1.5 Start/stop times Power-on to Ready (sec) 6.5 (typical) Standby to Ready (sec) 6.5 (typical) Ready to spindle stop
Summary of the content on the page No. 14
6 ST310014ACE Product Manual, Rev. D Note. These drives are designed to meet the seek times represented in this manual consistently. Physical seeks, regardless of mode (such as track-to-track and average), are expected to meet or exceed the noted values. However, due to the manner in which these drives are formatted, benchmark tests that include com- mand overhead or measure logical seeks may produce results that vary from these specifications. 1.7 Power specifications The drive receives D
Summary of the content on the page No. 15
ST310014ACE Product Manual, Rev. D 7 not spinning, and the servo and read/write electronics are in power- down mode. Typical Amps Means Power Mode Typical Watts 5V 12V Spinup — 0.90 1.90 Seek (Random, no read/write) 6.0 0.672 0.220 Operating (read/write) 5.5 0.572 0.220 Idle 4.5 0.468 0.180 Standby 1.2 0.192 0.020 Sleep 1.0 0.157 0.018 Typical current profile Current (amps) 2.0 1.0 0.0 -1.0 12 3 4 5 6 Time (seconds) Figure 1. Typical startup and operation current profile
Summary of the content on the page No. 16
8 ST310014ACE Product Manual, Rev. D 1.7.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injec
Summary of the content on the page No. 17
ST310014ACE Product Manual, Rev. D 9 established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disc access is necessary. Sleep mode The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it recei
Summary of the content on the page No. 18
10 ST310014ACE Product Manual, Rev. D 1.8.3 Humidity 1.8.3.1 Relative Humidity Operating 5% to 90% noncondensing (30% per hour max) Nonoperating 5% to 95% noncondensing (30% per hour max) 1.8.3.2 Wet bulb temperature Operating 29.4°C (84°F) max Nonoperating 40.0°C (104°F) max 1.8.4 Altitude Operating –60.96 m to 3,048 m (–200 ft to 10,000+ ft) Nonoperating –121.92 m to 12,192 m (–400 ft to 40,000+ ft) 1.8.5 Shock All shock specifications assume that the drive is mounted securely with the
Summary of the content on the page No. 19
ST310014ACE Product Manual, Rev. D 11 1.8.6.1 Operating vibration The following table lists the maximum vibration levels that the drive may expe- rience while meeting the performance standards specified in this document. 5–21 Hz 0.02-inch displacement (peak to peak) 22–350 Hz 0.5 Gs acceleration (zero to peak) 351–500 Hz 0.25 Gs acceleration (zero to peak) 1.8.6.2 Nonoperating vibration The following table lists the maximum nonoperating vibration that the drive may experience without incur
Summary of the content on the page No. 20
12 ST310014ACE Product Manual, Rev. D 1.10 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Test Description Performance Reference Level Standard Electrostatic Contact, HCP, VCP: ± 4 kV; Air: B EN 61000-4-2: 95 ± 8 kV discharge Radiated RF 80 to 1,000 MHz, 3 V/m, A EN 61000-4-3: 96 immunity 80% AM with 1 kHz s
