Summary of the content on the page No. 1
Product Manual
®
Momentus 5400 FDE.3 SATA
ST9320322AS
ST9160312AS
ST9120312AS
100513273
Rev. A
June 2008
Summary of the content on the page No. 2
©2008, Seagate Technology LLC All rights reserved. Publication number: 100513273, Rev. A June 2008 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Momentus, Seagate- SeaBOARD, SeaFONE, SeaTDD, and SeaTools are either trademarks or registered trade- marks of Seagate Technology LLC or one of its affiliated companies in the United States and/ or other countries. All other trademarks or registered trade
Summary of the content on the page No. 3
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 System requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 About Momentus 5400 FDE.3 SATA disc drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1.2.1 Drive state upon shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
4.0 Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.1 Hot-Plug compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.2 Serial ATA device plug connector pin definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 4.2.1 ATA Security policy exceptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 5
List of Figures Figure 1. Typical +5V only startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 2. Serial ATA connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 4. Mounting dimensions . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 6
Summary of the content on the page No. 7
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Momentus 5400 FDE.3 SATA model drives: ST9320322AS ST9160312AS ST9120312AS These drives provide the following key features: � DriveTrust technology including: � Hardware-based Full Disc Encryption (FDE) � DriveTrust security interface and ATA security interface � Integrates with standard security software packages to provide features such as: Pre-boot authentica- tion and i
Summary of the content on the page No. 8
1.2 About Momentus 5400 FDE.3 SATA disc drives ® The Momentus 5400 FDE.3 SATA drives contain DriveTrust technology providing Full Disc Encryption (FDE) using proven Advanced Encryption Standard (AES) data encryption and decryption. You can elect to use Momentus 5400 FDE.3 SATA drives in one of two different security modes: 1. The ATA Security mode To operate in ATA Security mode, you only need a host system and operating system that supports the existing ATA Security Command Set. The drive is
Summary of the content on the page No. 9
Having the encryption/decryption on the drive also provides the highest level of security for data because all data, including the boot sector bytes, operating system, temp and even the swap files are encrypted at the drive level. 1.2.1 Drive state upon shipment Upon shipment from the Seagate factory, the ATA Security Interface is enabled and functioning. This is referred to as operating in ATA Security mode. The following is the detailed state of the drive upon shipment. � Full Disc Encrypti
Summary of the content on the page No. 10
4 Momentus 5400 FDE.3 SATA Product Manual, Rev. A
Summary of the content on the page No. 11
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual. Table 2: Drive specifications Drive specification ST9320322AS ST9160312AS ST9120312AS Formatted Gbytes (512 bytes/sector)* 320 160 120 Guaranteed sectors 625,142,448
Summary of the content on the page No. 12
Table 2: Drive specifications Drive specification ST9320322AS ST9160312AS ST9120312AS Idle mode, low power (typical) 0.7 watts Standby mode 0.24 watts (typical)*** Sleep mode 0.24 watts (typical)*** Voltage tolerance (including noise) +5V ± 5% Ambient temperature 0° to 60°C (operating), –40° to 70°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 35°C (nonoperating) Relative humidity 5% to 95% (operating) 5% to 95% (nonoperating) Relative humidity gradient 30% per hour m
Summary of the content on the page No. 13
power to operational levels. ***Typical notebooks will pull power to the drive when entering S3 and S4; while in the S3 and S4 states, drive sleep and drive standby modes will not contribute to battery power consumption. 2.2 Formatted capacity Model Formatted capacity* Guaranteed sectors Bytes per sector ST9320322AS 320 Gbytes 625,142,448 512 ST9160312AS 160 Gbytes 312,581,808 512 ST9120312AS 120 Gbytes 234,441,648 512 *One Gbyte equals one billion bytes when referring to hard drive capaci
Summary of the content on the page No. 14
2.4 Physical organization Drive model Read/write heads Number of discs ST9320322AS 4 2 ST9160312AS 2 1 ST9120312AS 2 1 2.5 Recording and interface technology Interface Serial ATA (SATA) Recording method Perpendicular Recording density BPI (bits/inch max) 1,337k Track density TPI (tracks/inch max) 191.5k 2 253 Areal density (Gbits/inch max) Spindle speed (RPM) (± 0.2%) 5,400 Maximum Internal transfer rate (Mbits/sec) 830 I/O data-transfer rate (Gbits/sec max) 3.0 Interleave 1:1 Cache buffer 8
Summary of the content on the page No. 15
2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: � Track-to-track seek time is an average of all possible single-track seeks in both directions. � Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead. Typical seek times (msec) Read Track-to-track 1.5 Average 11.0 Ful
Summary of the content on the page No. 16
2.9 Power specifications The drive receives DC power (+5V) through a native SATA power connector. 2.9.1 Power consumption Power requirements for the drives are listed in table 3. Typical power measurements are based on an average of drives tested, under nominal conditions, at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. � Seek mode During seek mode, the read/write actuator arm moves toward
Summary of the content on the page No. 17
2.9.1.1 Typical current profile Figure 1. Typical +5V only startup and operation current profile 2.9.2 Deferred spinup Momentus 5400 FDE.3 SATA drives do not support the deferred spinup option. If you require this option, refer to the Momentus 5400.3 SATA Blade Server family of drives. 2.9.3 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a m
Summary of the content on the page No. 18
2.9.5 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Table 4: Power management modes Power modes Heads Spindle Buffer Active (operating) Tracking Rotating Full power Idle, performance Tracking Rotating Self refresh—low power Idle, active Floating Rotating Self refresh—low power Idle, low power
Summary of the content on the page No. 19
2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 65°C (149°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum temperature is derated linearly by 1°C every 1000 feet. Operating 0° to 60°C (32° to 140°F) Nonoperating –40° to 70°C (–40° to 158°F) 2.10.2 Temperature gradient Operating 20°C per hour (
Summary of the content on the page No. 20
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 350 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.2 Nonoperating shock The nonoperating shock leve
