Summary of the content on the page No. 1
. . . . . . . . . . . . . . . . . . . . . . .
HAWK 4 Family:
. . . . . . . . . . . . . . . . . . . . . . .
(Wide Bus)
. . . . . . . . . . . . . . . . . . . . . . .
ST15230W/WD/WC
. . . . . . . . . . . . . . . . . . . . . . .
ST15230DC
. . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 2
Contents Introduction........................................................... 1 Electromagnetic interference ................................ 1 Before you begin .................................................. 3 Installation overview ....................................... 8 Product repair information .................................... 10 Shipping ......................................................... 11 Product repair and return information ............. 11 Technical support servi
Summary of the content on the page No. 3
Hawk 4 (Wide) Family Install Guide, Rev. A 1 ___________________________________________ Introduction Before attempting any installation, please read through all applicable sections of this document, including all warnings and cautions. Warning. This equipment generates, uses and can radiate radio frequency energy and if not installed in accordance with these instruc- tions, may cause interference to radio com- munications. Electromagnetic interference (EMI) con- siderations The dri
Summary of the content on the page No. 4
2 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ The physical design characteristics of the drive(s) described herein, serve to minimize EMI radiation when installed in an enclosure that provides reason- able shielding. As such, the drive(s) are capable of meeting the Class B limits of the FCC Rules and the Regulations of the Canadian Department of Communi- cations. Note. It is the end users' responsibility to assure that the drive(s) descri
Summary of the content on the page No. 5
Hawk 4 (Wide) Family Install Guide, Rev. A 3 ___________________________________________ Before you begin Verify that the system is switched off and discon- nected from main power before any installation is attempted. Protect yourself, the drive, and your valuable pro- grams and data by reading the following cautions and warnings. • Do not unpack drive from its static shielded bag until you are ready to install it in the system. • Always handle the drive by the frame or casting. •
Summary of the content on the page No. 6
4 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ • Inspect drive for possible shipping damage. All claims of this type should be filed promptly with the trans- porter involved. Save original packing materials to be used when reshipping. • Verify all parts listed on shipping bill are received with the equipment. Discrepancies or damage should be reported to the shipping company. • When transporting or shipping a drive or system, please ensure t
Summary of the content on the page No. 7
Hawk 4 (Wide) Family Install Guide, Rev. A 5 ___________________________________________ To insure optimum reliable equipment op- eration, it is required that technical support personnel discharge themselves by wearing a grounding strap around the wrist and be connected to a grounding terminal while working in the vicinity of, and while handling EOS/ESD susceptible assemblies/parts. If unavailable, ground yourself frequently by touching the metal chassis of the system before handlin
Summary of the content on the page No. 8
6 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Safety instructions 1. The disc drive(s) are to be installed in a customer supplied enclosure where the surrounding air does o not exceed 50 C. 2. Four (4) 6-32 UNC-2A screws are required for installation. Maximum screw length into side of drive is 0.15 inches (3.81 mm). Maximum screw length into bottom is 0.20 in. (5.08 mm). Maximum screw tightening torque is 6.0 in-lb (.675 NM) with minimum th
Summary of the content on the page No. 9
Hawk 4 (Wide) Family Install Guide, Rev. A 7 ___________________________________________ Sicherheitsanleitung 1. Däs Gerät ist ein Einbaugerät, vorgesehen für eine o maximale Umgebungstemperatur von 50 C. 2. Zur Befestigung der Drive werden 4 Schrauben benötigt (6-32 UNC-2A). Die maximale Länge der Schrauben in der unteren Seite des Chassis darf nicht mehr als 0.20 in (5.08 mm) betragen, die in der oberen 0.15 in (3.81 mm). Maximalle Schraubenanziehung von 6.0 in-lb. (.675 NM) mit m
Summary of the content on the page No. 10
8 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Installation Overview Installation of the drive can be divided into distinct phases as outlined below. Some of these may not be applicable to your particular installation requirements. Refer to the individual drive installation sections for specific information on your drive model. • Drive configuration: The user must select which of the drive features are appropriate to enable for instal- latio
Summary of the content on the page No. 11
Hawk 4 (Wide) Family Install Guide, Rev. A 9 ___________________________________________ • Low-level formatting: After the drive has been properly configured for the system, it does not need to be low-level formatted, as this has been done by the factory and does not require this step during installation. (The low-level format writes the sector boundaries and track information to the drive). Defect management information is read from the drive by the host system when required in the
Summary of the content on the page No. 12
10 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Product repair information Service requirements The special facilities required for the manufacture of these drives generally prohibit repair in the field. If problems occur during installation, please contact your supplier for assistance. Do not attempt to disassemble or repair. Drives should be sent to the repair depot through the purchase source, if possible. Please ob- serve the following c
Summary of the content on the page No. 13
Hawk 4 (Wide) Family Install Guide, Rev. A 11 ___________________________________________ Shipping: When transporting or shipping a drive, a Seagate approved container must be used. Keep your original box. They are easily identified by the Seagate Approved Package label. Shipping a drive in a non- approved container voids the drive warranty. Seagate repair centers may refuse receipt of compo- nents improperly packaged or obviously damaged in transit. Contact your Authorized Seagate D
Summary of the content on the page No. 14
12 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ If the drive is no longer under warranty contact pur- chase source for repair information or refer to numbers listed in the following paragraph . Technical support services Please contact your dealer for technical support and installation troubleshooting. Product Technical Sup- port is available for all Seagate products by calling the SeaFAX, SeaFone, SeaTDD or SeaBOARD services. These are toll
Summary of the content on the page No. 15
Hawk 4 (Wide) Family Install Guide, Rev. A 13 ___________________________________________ SeaTDD: 408/438-5382 TDD is a Telecommunication Device for the Deaf where two people can communicate using a keyboard that is connected to the phone line. A TDD device is required to access this service. This service is available from 8:00 AM to 5:00 PM PST, Monday through Friday. SeaBOARD: The Seagate Technical Support Bulletin Board System (BBS) is available 24 hours a day, 7 days a week. A mo
Summary of the content on the page No. 16
14 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ With this service you can access: • Specifications and jumper configurations for all Seagate products. • Reprints of Seagate documentation. • A directory of information and helpful utilities that you can download to your own computer. BBS Modem Location Number USA, Mexico, Latin America 408/438-8771 Canada 416/856/5581 England 44-62-847-8011 France 33-1-40-67-1034 Germany 49-89-140-9331 Singapor
Summary of the content on the page No. 17
Hawk 4 (Wide) Family Install Guide, Rev. A 15 ___________________________________________ Drive specifications Product Hawk 4 family (wide) Information ST15230W ST15230WD ST15230WC ST15230DC Interface [7] SCSI-2 Fast SCSI-2 Fast Cache Type Multi-segmented, 256 Kb* Capacity MB Unformatted 5170 5170 Formatted [1] 4294 4294 Cylinders 3992 3992 Heads 19 19 Sectors/track (Avg.)[8] 114 114 Recording method RLL (1,7) RLL (1,7) Rev/min 5411 5411 Seek time (ms typ.) [2] Average R
Summary of the content on the page No. 18
16 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ Notes. [1] Standard units are factory formatted with 512 data bytes per sector. ST15230 OEM standard models have twelve spare sectors per cylinder and 2 cylinders at inner tracks reserved for spares. [2] Does not Include on-board controller overhead. [3] Maximum measured at any location on top cover. o o [4] For best reliability keep below 35 C (95 F). [5] A droop of up to -10% is permissible
Summary of the content on the page No. 19
Hawk 4 (Wide) Family Install Guide, Rev. A 17 ___________________________________________ Initial setup information For the initial setup connect the cables, set the SCSI bus address and enable or disable (as required by system configuration), the SCSI I/O line terminator resistors (model "W" drives only). Note whether the drive model number ends in W, WC, DC or WD. These procedures are described in paragraphs following. SCSI interface cable connection The drives covered by this manu
Summary of the content on the page No. 20
18 Hawk 4 (Wide) Family Install Guide, Rev. A ___________________________________________ J1 J1-Auxiliary Pin
Power
1P
+12V
2P
+12V ret
3P
+ 5V ret
4P 3P 2P 1P 4P + 5V 68 Pin SCSI I/O
DC Power
Connector Connector Figure 1. DC power connection, 68 pin SCSI I/O connector ST15230WC and ST15230DC model drives receive power from the host computer through the 80 pin combined SCSI I/O and power connector (not shown, since a separate DC power cable not required). No separate DC
