Summary of the content on the page No. 1
Product Manual
®
Constellation ES Serial ATA
ST32000644NS
ST31000524NS
ST3500514NS
100516232
Rev. D
April 2010
Summary of the content on the page No. 2
Revision history Revision Date Sheets affected or comments Rev. A 08/26/09 Initial release. Rev. B 09/23/09 3-4, 6 and 13. Rev. C 01/11/10 4, 13, 16 and 20. 1, 5, 9-11,14-15 & 17-18. (move & revise tech support section, op Rev. D 04/21/10 temp, humidity, shock, vibe, dc pwr & sct-transport) © 2010 Seagate Technology LLC. All rights reserved. Publication number: 100516232, Rev. D, April 2010 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the
Summary of the content on the page No. 3
Contents 1.0 Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2.1 About the Serial ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
ii Constellation ES Serial ATA Product Manual, Rev. D
Summary of the content on the page No. 5
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Figure 3. Attaching SATA cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 4. Mounting dimensions—top, side and end view . . . . . . . . . . . . .
Summary of the content on the page No. 6
Summary of the content on the page No. 7
1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES For information regarding products and services, visit http://www.seagate.com/www/en-us/about/contact_us/ Available services include: Presales & Technical support Global Support Services telephone numbers & business hours Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance For information regarding Data Recovery Services,
Summary of the content on the page No. 8
2.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate ® Constellation ES Serial ATA model drives: ST32000644NS ST31000524NS ST3500514NS These drives provide the following key features: • 7200 RPM spindle speed. • PowerChoice™ for selectable power savings • Top Cover Attached motor for excellent vibration tolerance • High instantaneous (burst) data-transfer rates (up to 300MB per second). • Perpendicular recording technology pro
Summary of the content on the page No. 9
2.1 About the Serial ATA interface The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary advantages include: • Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump- ers or other configuration options. • Thinner and more flexible cabling for improved enclosure airflow and ease of installation. • Scalability to higher performance levels. In addition, Serial ATA makes the transition f
Summary of the content on the page No. 10
3.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST32000644NS ST31000524NS ST3500514NS 3.1 Specification summary tables The specifications listed in the following tables are for quick reference. For details on specification measure- ment or definition, see the appropriate section of th
Summary of the content on the page No. 11
Drive specification ST32000644NS ST31000524NS ST3500514NS Power-on to ready (sec max) 15 10 7 Standby to ready (sec max) 15 10 7 Track-to-track seek time (ms typical) 0.5 read 0.8 write Average seek, read (ms typical) <8.5 Average seek, write (ms typical) <9.5 Startup current (typical) 12V (peak) 2.8A 2.0A (optional configuration through Smart Command Transport) Voltage tolerance (including noise) 5V ± 5% 12V ± 10% Ambient temperature 5° to 60°C (operating/tested) –40° to 70°C (nonoperating
Summary of the content on the page No. 12
3.2 Formatted capacity Formatted Guaranteed Model capacity* sectors Bytes per sector ST32000644NS 2TB 3,907,029,168 ST32000544NS 1TB 1,953,525,168 512 ST31000524NS 500GB 976,773,168 *One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 3.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed s
Summary of the content on the page No. 13
3.5 Physical characteristics Maximum height 26.1mm (1.028 in) Maximum width 101.6mm (4.000 +/- 0.010 in) Maximum length 146.99mm (5.787 in) Max weight ST32000644NS 710g (1.565 lb) ST31000524NS 640g (1.411 lb) ST3500514NS 610g (1.345 lb) Cache buffer 64MB (64,768KB) ST32000644NS ST31000524NS and ST3500514NS 32MB (32,768KB) 3.6 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the tabl
Summary of the content on the page No. 14
3.8 Power specifications The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 3 on page 24. 3.8.1 Power consumption Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operat
Summary of the content on the page No. 15
Table 2: 2000GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.26 0.42 6.38 0.27 0.42 6.39 Advanced Idle Current * Idle_A 0.13 0.35 4.83 0.14 0.42 5.70 Idle_B 0.13 0.36 5.01 0.14 0.36 5.00 Idle_C 0.13 0.22 3.26 0.14 0.22 3.27 Standby 0.09 0.01 0.51 0.09 0.01 0.53 Transition Current * Idle_A (Active) 0.86 1.66 24.22 0.98 0.90 15.70 Idle_B (Active) 0.76 1.72 24.47 0.74 1.64 23.42 Idle_C (Active
Summary of the content on the page No. 16
Table 3: 1000GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.27 0.27 4.59 0.27 0.27 4.61 Advanced Idle Current * Idle_A 0.14 0.27 3.86 0.15 0.27 3.99 Idle_B 0.14 0.23 3.53 0.15 0.23 3.56 Idle_C 0.14 0.08 1.70 0.15 0.08 1.73 Standby 0.09 0.01 0.54 0.10 0.01 0.57 Transition Current * Idle_A (Active) 0.86 0.98 16.06 0.86 1.06 17.02 Idle_B (Active) 0.80 1.32 19.90 0.76 1.27 19.02 Idle_C (Active
Summary of the content on the page No. 17
Table 4: 500GB Drive DC power requirements 1.5Gb mode 3.0Gb mode Voltage +5V +12V Power +5V +12V Power Regulation ±5% ±5% (Watts) ±5% ±5% (Watts) Avg Idle Current * 0.26 0.20 3.71 0.28 0.20 3.74 Advanced Idle Current * Idle_A 0.13 0.21 3.13 0.14 0.21 3.17 Idle_B 0.13 0.18 2.82 0.14 0.18 2.85 Idle_C 0.13 0.07 1.50 0.14 0.07 1.52 Standby 0.09 0.01 0.53 0.09 0.01 0.55 Transition Current * Idle_A (Active) 0.84 0.52 10.44 0.84 0.54 10.68 Idle_B (Active) 0.70 1.11 16.81 0.80 1.13 17.56 Idle_C (Active)
Summary of the content on the page No. 18
3.8.1.1 Typical current profiles 12 Constellation ES Serial ATA Product Manual, Rev. D
Summary of the content on the page No. 19
Figure 1. Typical 5V startup and operation current profile Figure 2. Typical 12V startup and operation current profile 3.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 V line or an equivalent 15-ohm resistive load on the +5V line. • Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave injected noise at up to 10MHz. • Using 5V power, the drive is expected to op
Summary of the content on the page No. 20
3.8.4 Power-management modes The drive provides programmable power management to provide greater energy efficiency. In most systems, you can control power management through the system setup program. The drive features the following power-management modes: Power modes Heads Spindle Buffer Active Tracking Rotating Enabled Idle_a ID Biased Rotating Enabled Idle_b Parked Rotating Enabled Idle_c Parked Rotating at lower RPM Enabled Standby Parked Stopped Enabled Sleep Parked Stopped Disabled • Act
