Summary of the content on the page No. 1
Users Guide
U Series 9
ST3160022A
ST3120025A
ST380012A
ST360019A
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Users Guide U Series 9 ST3160022A ST3120025A ST380012A ST360019A
Summary of the content on the page No. 4
©2003, Seagate Technology LLC All rights reserved Publication number: 100286682, Rev. D December 2003 Seagate, Seagate Technology, and the Seagate logo are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, and SeaTDD are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. Seagate reserves the right to change, without notice, product offerings or specifications. No part
Summary of the content on the page No. 5
Revision status summary sheet Revision Date Sheets Affected Rev. A 04/21/03 All. Rev. B 05/07/03 Pages 6, 30-32, and 37-41 Rev. C 07/14/03 Pages 1, 4, 7, 12, and 13. Also new design and page size. Rev. D 12/01/03 Page 16.
Summary of the content on the page No. 6
Summary of the content on the page No. 7
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 8
vi U Series 9 Product Manual, Rev. D
Summary of the content on the page No. 9
List of Figures Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Figure 3. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 4. Master/slave jumper settings . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
viii U Series 9 Product Manual, Rev. D
Summary of the content on the page No. 11
1.0 Introduction ® This manual describes the functional, mechanical and interface specifications for the following Seagate ® Barracuda 7200.7 model drives: ST3160022A ST3120025A ST380012A ST360019A These drives provide the following key features: High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. Giant magnetoresistive (GMR) recording heads and EPRML technology, which provide the drives with increased areal density. State-of-the-a
Summary of the content on the page No. 12
2 U Series 9 Product Manual, Rev. D
Summary of the content on the page No. 13
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST3160022A, ST3120025A, ST380012A, and ST360019A model drives. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or defi- nition, see the appropriate section of this manual. Dri
Summary of the content on the page No. 14
Drive specification ST3160022A ST3120025A ST380012A ST360019A Read/write power (typical) 12.0 watts Idle mode (typical) 7.5 watts Standby mode (typical) 0.9 watts Sleep mode (typical) 0.9 watts Voltage tolerance (including noise) 5V ± 5% 12V ± 10% Ambient temperature 0° to 60°C (operating) –40° to 70°C (nonoperating) Temperature gradient (°C per hour max) 20°C (operating) 30°C (nonoperating) Relative humidity 5% to 90% (operating) 5% to 95% (nonoperating) Relative humidity gradient 30% per
Summary of the content on the page No. 15
2.2 Formatted capacity Formatted Guaranteed Model capacity sectors Bytes per sector ST3160022A 160 Gbytes 312,581,808 512 ST3120025A 120 Gbytes 234,441,648 512 ST380012A 80 Gbytes 156,301,488 512 ST360019A 60 Gbytes 117,231,408 512 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. See Section 4.1.2, "Identify Device command" (words 60-61 and 100-103) for additio
Summary of the content on the page No. 16
2.6 Physical characteristics Drive specification Maximum height (mm) 26.035 (inches) 1.028 Maximum width (mm) 101.6 (inches) 4.00 Maximum length (mm) 146.99 (inches) 5.787 Typical weight (grams) 635 (pounds) 1.4 2.7 Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: Track-to-track seek time is an average of all possible single-track seeks in bo
Summary of the content on the page No. 17
2.9.1 Power consumption Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. Seek mode During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
Summary of the content on the page No. 18
2.9.1.1 Typical current profile 1.2 1.0 0.8 Amps 0.6 0.4 0.2 +5 Volt Current during spindle start — Typical Amperes 0.0 12 3 4 5 6 7 8 9 Seconds Figure 1. Typical 5V startup and operation current profile 3.0 +12 Volt Current during spindle start — Typical Amperes 2.5 2.0 Amps 1.5 1.0 0.5 0.0 01 2 3 4 5 6 7 8 Seconds Figure 1. Typical 12V startup and operation current profile 8 U Series 9 Product Manual, Rev. D
Summary of the content on the page No. 19
2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note. Equival
Summary of the content on the page No. 20
activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 2.10 Environmental specifications 2.10.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions. Above 1,000 feet (305 meters), the maximum
