Summary of the content on the page No. 1
Communication Drivers
Installation manual
eng
35006152 00
Summary of the content on the page No. 2
2
Summary of the content on the page No. 3
Table of Contents About the Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Part I General information on the installation of drivers . . . . . 9 At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Chapter 1 General information concerning the Drivers . . . . . . . . . . . . . .11 At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 4
Configuration of the Windows 2000\XP operating system. . . . . . . . . . . . . . . . . . 42 Configuration of the Windows NT operating system . . . . . . . . . . . . . . . . . . . . . . 43 Chapter 5 TSX FPC 10 ISA card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 How to install the driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 5
How to adjust the ISA TPCX 57 card parameters. . . . . . . . . . . . . . . . . . . . . . . 108 Chapter 9 PCIWAY driver for TSX PCI 57 • processors . . . . . . . . . . . .111 At a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 How to install the driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Configuring the PCIWAY driver for windows 2000\XP . . . . . . . . . . . . . . . . . . . 1
Summary of the content on the page No. 6
6
Summary of the content on the page No. 7
About the Book At a Glance Document Scope This document deals with the installation of communication drivers for Windows 98, Windows 2000/XP and Windows NT operating systems. These drivers are: Uni-Telway: on the serial port, with a TSXSCP114 card. Fip: with a TSXFPC10 card, with a TSXFPP20 card. Ethway, XIP on TCPIP, drivers for Atrium: Isaway for the ISA bus, PCIWAY for the PCI bus. Modbus, USB. Validity Note The data and illustrations found in this documentation are
Summary of the content on the page No. 8
About the Book Product Related Schneider Electric assumes no responsibility for any errors that may appear in this Warnings document. If you have any suggestions for improvements or amendments or have found errors in this publication, please notify us. No part of this document may be reproduced in any form or by any means, electronic or mechanical, including photocopying, without express written permission of Schneider Electric. All pertinent state, regional, and local safety regulations mus
Summary of the content on the page No. 9
General information on the installation of drivers I At a Glance Subject of this This part describes the installation principle of the various drivers using the Part CD ROM. What’s in this This part contains the following chapters: Part? Chapter Chapter Name Page 1 General information concerning the Drivers 11 9
Summary of the content on the page No. 10
General 10
Summary of the content on the page No. 11
General information concerning the Drivers 1 At a Glance Subject of this This chapter provides general information on the drivers. chapter What’s in this This chapter contains the following topics: Chapter? Topic Page Installation 12 The drivers and Unity Pro 14 11
Summary of the content on the page No. 12
General information concerning the Drivers Installation At a Glance It is generally possible to launch the installation of all the drivers using the same procedure. Procedure The following procedure describes the installation principle of a driver using the CD ROM. Step Description 1 Insert the CD ROM in the CD ROM drive. Result: the Install.htm file launches automatically. 2 Click on the link (in blue underlined text) that corresponds to the driver you wish to install. Result: the Downloadin
Summary of the content on the page No. 13
General information concerning the Drivers Step Description 4 Then click on OK to confirm your choice. Result: the Safety warning window appears. Security warning Do you wish to install and run "SETUP.EXE from D:\ CDRom\UNITELWAY\Win2000-XP-Win 98-Me\disk1"? Impossible to identify this editor for the following reasons: The object to be verified is unknown to the supplier of reliability certificates. Yes No Further info. 5 Click on Yes to go ahead with the installation. Result: the installatio
Summary of the content on the page No. 14
General information concerning the Drivers The drivers and Unity Pro Precautions To ensure correct operation of the drivers using the Unity Pro software range you should install or reinstall the drivers using the CDROM version ≥ V2.0. Drivers that normally operate using the Unity Pro software range should also be installed using Windows XP or Windows 2000. 14
Summary of the content on the page No. 15
Uni-Telway drivers II At a Glance Subject of this This part describes how to install the drivers associated with Uni-Telway Part communication for Windows 98, Windows 2000\XP and Windows NT operating systems. What’s in this This part contains the following chapters: Part? Chapter Chapter Name Page 2 Serial port 17 3 TSX SCP 114 card 27 15
Summary of the content on the page No. 16
Uni-Telway drivers 16
Summary of the content on the page No. 17
Serial port 2 At a Glance Subject of this This chapter describes installation of the Uni-Telway driver communicating in slave Chapter mode on the serial port with a remote device. Driver installation consists of two steps: installation of files on the station, configuration of the driver. What’s in this This chapter contains the following topics: Chapter? Topic Page How to install the driver 18 Driver configuration screens 20 How to configure the driver 24 17
Summary of the content on the page No. 18
Serial port How to install the driver At a Glance Driver installation is a standard installation. It can be launched either: from the drivers’ CD-ROM, or from disks if the station has no CD-ROM drive. Note: The installation disks are created from the CD-ROM. How to create a Use the following procedure to create installation disks: set of disks Step Action 1 Use a station with a CD-ROM drive. 2 Insert the CD-ROM into the drive. 3 Access the directory of the driver to be copied onto disk. 4 Co
Summary of the content on the page No. 19
Serial port How to install the To install the driver, carry out the following procedure: driver Start of installation No Installation by st Insert the 1 disk in the drive CD-ROM? Yes Insert CD-ROM in CD-ROM drive Appearance No Access the directory of the driver of the file to be installed corresponding to INSTALL.HTM the PC’s operating system ? Yes Click on the link which corresponds to the driver to be installed Access the directory DISK1 Choose Run this program from its current location
Summary of the content on the page No. 20
Serial port Driver configuration screens At a Glance The configuration tool is used to link a driver configuration profile to a remote device that communicates with the station. Illustration The screen dedicated to the Uni-Telway driver looks like this: Uni-Telway Configuration Station List 1 Target Station: [Default] 2 Station ID Remote Password Ph [Default] COM 1 3 Add Modify Delete 6 4 5 OK Cancel Apply 7 Description This table describes the different areas which make up the configuration
