Rosewill RX81US-HT-25A-BLK user manual

Summary of the content on the page No. 1

External Enclosure for
2.5" SATA to USB + eSATA
RX81US-HT-25A-BLK
User Manual

Summary of the content on the page No. 2

External Enclosure for 2.5” SATA to USB + eSATA User Manual Please read this installation carefully before you use the products. Precaution: 1. If it is a new HDD, needs to processing the disk partition 2. Win98SE and WinME do not recognize NTFS formatted drives, so if you want to use your drive on those platforms, we recommend you to use FAT32 instead. 3. Mac OS does not recognize NTFS formatted drives, to use your device on both platforms,

Summary of the content on the page No. 3

External Enclosure for 2.5” SATA to USB + eSATA User Manual Feature • Standard USB 2.0 high speed transfer rate. • Support Serial ATA. (USB + eSATA). • eSATA transfer rate up to 3.0Gbps(NCQ support) • Suitable for 2.5" HDD. • All aluminum, to enhance heat dissipation. • Plug and play / hot swappable. • OS support Win 98SE/ME/2000/XP/Vista/Mac OS 8.6 above. Technical Specifications USB v 2.0 / eSATA Bus Interfaces: USB 2.0 = 480 Mbps

Summary of the content on the page No. 4

External Enclosure for 2.5” SATA to USB + eSATA User Manual Installation Guide 1. Release the screws to pull out the HDD frame. 2. Fix the HDD by screws (after HDD located with the connecter). 3. Pull in the frame into external box. 4. Fasten the rear panel by screws. 5. After connect transfer cable and Power cord, the external HDD will appear the relativity.

Summary of the content on the page No. 5

External Enclosure for 2.5” SATA to USB + eSATA User Manual Attention • Only one interface at the time can be used(combo model) • If this HDD is new one, please partition & format disk, otherwise the system cannot detect HDD. • The HDD jumper should be set to “master”. • Make sure your PCI Host Card is installed correctly • If required, update your OS (win 2000 to SP4, Win XP to SP1a) • Only one computer at the time can access the drive

Summary of the content on the page No. 6

External Enclosure for 2.5” SATA to USB + eSATA User Manual The divided partition of the external HDD Win 98SE/ME SYSTEM FDISK is command that doing the divided partition to HDD, The step of how to divided partition from the HDD by using FDISK as follows: 1. Plug the cable of USB into PC, and be sure that the PC has identified HDD. 2. Execute "FDISK" under the model of COMMAND. 3. After enter the FDISK program [If the FDISK program does

Summary of the content on the page No. 7

External Enclosure for 2.5” SATA to USB + eSATA User Manual Notice: If you want your ENCLOSURE on a Windows as well as on your Mac OS, we recommend you to use a PC to format the drive. Choose FAT32 format and do not change anything on the partition or format on your Mac, otherwise the Windows OS can not be able to recognize the ENCLOSURE. To remove the device: For Windows 98SE Users Before you remove your device please wait for “Access L

Summary of the content on the page No. 8

External Enclosure for 2.5” SATA to USB + eSATA User Manual software (download from the Internet) in the PC, format to the MAC model. If you used the MO storage before, you must familiar and have more experience about it because MO storage has the same problem when doing the format. Why I can not see the drive? If you can not see the drive, make sure the jumper settings of your hard drive is “master”.