Summary of the content on the page No. 1
REJ10B0239-0140
M3S-UFLA32R
User’s Manual
UART Flash Memory Programming Utility
All information contained in these materials, including products and product specifications,
represents information on the product at the time of publication and is subject to change by
Renesas Technology Corp. without notice. Please review the latest information published
by Renesas Technology Corp. through various means, including the Renesas Technology
Corp. website (http://www.renesas.com).
Rev.1.40
Re
Summary of the content on the page No. 2
Notes regarding these materials 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this do
Summary of the content on the page No. 3
Precautions on Using The Product Described Herein 1. The product described herein should be used in combination with the parts included with the starter kit. If the product is operated in combination with any other item, its operation cannot be guaranteed. Nor will requests for help or suggestion be answered. 2. The product described herein was prepared for program development or evaluation purposes. The product cannot be used for the mass production. 3. Renesas Technology Corporation
Summary of the content on the page No. 4
Contents 1. Overview .......................................................................................................................1 2. System Configuration....................................................................................................1 2.1 Outline of the M3S-UFLA32R................................................................................................................ 1 2.2 Communication Cable (M3A-2145G50) ..................................
Summary of the content on the page No. 5
M3S-UFLA32R UART Flash Memory Programming Utility 1. Overview This user’s manual is intended to provide explanations about system configuration and operation method of the UART Flash Memory Programming Utility M3S-UFLA32R Ver.1.40 (hereinafter referred to as M3S-UFLA32R) for the M32R/ECU Series (Refer to the Table 2.3.1 for corresponding MCU). 2. System Configuration Figure 2.1.1 shows connection configuration of the system using the M3S-UFLA32R Target Board Communication Host
Summary of the content on the page No. 6
9 1 10 2 M3S-UFLA32R UART Flash Memory Programming Utility 2.2 Communication Cable (M3A-2145G50) Communication cable consists of two different cables below. •Interface Cable (M3A-2145G02) It is a conversion cable to connect to the test pins on the target when the connection cable for the MF-TEN-NINE can not be mounted on the target board. Figure 2.2.1 shows connecting diagram. •MF-TEN-NINE Cable (M3A-0652CBL) It is a cable to connect host PC to target board.
Summary of the content on the page No. 7
M3S-UFLA32R UART Flash Memory Programming Utility Figure 2.2.2 MF-TEN-NINE Cable Connecting Diagram REJ10B0239-0140/Rev.1.40 Mar. 2007 Page 3 of 30 RJJ99J0021-0100
Summary of the content on the page No. 8
M3S-UFLA32R UART Flash Memory Programming Utility Table 2.2.1 Usage Specification Rated Value Parameter Unit Condition MIN MAX 3.0 3.6 V Target Supply Voltage DC Power Supply 4.5 5.5 V Target Supply Voltage RS-232C Communication Rate 9600 115200 bps Communication Speed with PC Consumption Current - 60 mA MAX3221EAE Specification No Condensation, No Corrosive Gas Operating Ambient Temperature 5 35 °C Environment No Condensation, No Corrosive Gas Storage Ambient Temperature
Summary of the content on the page No. 9
M3S-UFLA32R UART Flash Memory Programming Utility 3. Installation of the M3S-UFLA32R 3.1 Installation of the M3S-UFLA32R To install the M3S-UFLA32R, perform the following steps. 1) Execute Setup.exe in "¥Eng¥Tool¥Ufla32r¥W95E" folder contained in the provided CD. (Note1) 2) Continue installation by following the instruction of the installation window. 3) Installation is completed when Setup Complete dialog appears. Note 1: To use the file which is downloaded from our homepage, un
Summary of the content on the page No. 10
M3S-UFLA32R UART Flash Memory Programming Utility 4. Operation Method of the M3S-UFLA32R 4.1 Startup Double-click the icon after the M3S-UFLA32R setup is completed. 4.2 Exit Choose [Exit(X)] from [File(F)] menu. 4.3 Operation Outline of the M3S-UFLA32R To write to the flash memory, perform the following steps. 1) Connecting Host PC to Target Board •Connect D-Sub 9 pin connector of the MF-TEN-NINE cable to COM1 of the host PC. •Connect MF-TEN-NINE cable to the interface c
Summary of the content on the page No. 11
M3S-UFLA32R UART Flash Memory Programming Utility 4) Reset the Target MCU Reset the target MCU by pressing the reset switch on the target board. 5) Starting the M3S-UFLA32R Start the M3S-UFLA32R. 6) Execution of Writing to the Flash Memory by the M3S-UFLA32R Operate the M3S-UFLA32R and perform writing to the flash memory. For detail about operation method, refer to "5. Function Description of the M3S-UFLA32R." Note: During erasing or writing, it is prohibited to reset
Summary of the content on the page No. 12
M3S-UFLA32R UART Flash Memory Programming Utility 5. Function Description of the M3S-UFLA32R 5.1 Function List Table 5.1 lists functions of the M3S-UFLA32R. Choose each function from menu or click a button for execution. Table 5.1 Function List Menu Button Function Reference File Load Refer Read the program data of specified Motorola S 5.2 format file into the internal buffer Exit - Exit the M3S-UFLA32R 5.3 Display Lock Bit Information - Display lock bit information 5.4 Devic
Summary of the content on the page No. 13
M3S-UFLA32R UART Flash Memory Programming Utility 5.2 Program Data (Motorola S-format file) Selection (1) Choose [Load(L)] from [File(F)] menu or click [Refer] button. Figure 5.2.1 Program Data Selection (2) When “Open File” dialog opens, choose a program data file (Motorola S-format file) and then click [Open(O)] button. Note: As a file format, the M3S-UFLA32R supports Motorola S-format only. Figure 5.2.2 Open File Dialog
Summary of the content on the page No. 14
M3S-UFLA32R UART Flash Memory Programming Utility (3) Choose a file to display the dialog that shows execution process, and then read program data file into the internal buffer. After completing read, the dialog is closed and file name is displayed in "File Name:" box. Figure 5.2.3 Result of Choosing Program Data 5.3 Exit the Application (1) Choose [Exit(X)] from [File(F)] menu to exit the program. Also, it is able to exit the program by pushing [Alt + F4] keys or clicking
Summary of the content on the page No. 15
M3S-UFLA32R UART Flash Memory Programming Utility 5.4 Lock Bit Information (1) Choose [Lock Bit Information (L)] from [Display(V)] menu to display the dialog that shows execution process, and then read lock bit. After completing read of lock bit, the dialog is closed and "Lock Bit Status Display" dialog is displayed. Figure 5.4.1 Lock Bit Information (2) Click [Cancel] while reading out lock bit status to close the dialog that shows execution process. Figure 5.4.2 Rea
Summary of the content on the page No. 16
M3S-UFLA32R UART Flash Memory Programming Utility (3) In [Lock Bit Status Display] dialog, the lock bit statuses of all blocks of currently selected MCU are displayed. Click [OK] to close "Lock Bit Status Display" dialog. Figure 5.4.3 Lock Bit Status Display Dialog REJ10B0239-0140/Rev.1.40 Mar. 2007 Page 12 of 30
Summary of the content on the page No. 17
M3S-UFLA32R UART Flash Memory Programming Utility 5.5 Program (1) Choose [Program(P)] from [Device(D)] menu or click [Program] button to display the dialog that shows execution process, and then write program data stored in the internal buffer to the flash memory. After completing write of program data, the dialog is closed and "Program …finish" dialog is displayed. Figure 5.5.1 Program (2) Click [OK] in the "Program…finish" dialog to close the dialog Figure 5.5.2 Pr
Summary of the content on the page No. 18
M3S-UFLA32R UART Flash Memory Programming Utility 5.6 Erase (1) Choose [Erase(E)] from [Device(D)] menu or click [Erase] button to display the dialog that shows execution process, and then erase the flash memory. After completing the flash memory erasing, the dialog is closed and "Erase …finish" dialog is displayed. Figure 5.6.1 Erase (2) Click [OK] in the "Erase…finish" dialog to close the dialog. Figure 5.6.2 Erase Finish Dialog REJ10B0239-0140/Rev.1.40 Mar. 2007 P
Summary of the content on the page No. 19
M3S-UFLA32R UART Flash Memory Programming Utility 5.7 Block Erase (1) Choose [Block Erase(L)] from [Device(D)] menu to display "Block Erase" dialog. Figure 5.7.1 Block Erase (2) In "Block Erase" dialog, all blocks of currently selected MCU are displayed. Click [Select All] to select all blocks. Click [Clear] button to clear all selected blocks. Select the blocks you wish to erase and click [OK] to close "Block Erase" dialog. Subsequently, the dialog that shows execution pr
Summary of the content on the page No. 20
M3S-UFLA32R UART Flash Memory Programming Utility (3) Click [OK] in the "Block Erase…finish" dialog to close the dialog. Figure 5.7.3 Block Erase Finish Dialog REJ10B0239-0140/Rev.1.40 Mar. 2007 Page 16 of 30
