Summary of the content on the page No. 1
CD-ROM DRIVE
PHONES BUSY
Operating instructions
Mode d'emploi
Bedienungsanleitung
Istruzioni per l'uso
DR-U16S
CD-ROM DRIVE UNIT
UNITE DE LECTEUR DE CD-ROM
CD-ROM –LAUFWERK
LETTORE DI CD-ROM
English
Français
IMPORTANT NOTICE:
Deutsch
RECORD THE MODEL NUMBER
AND SERIAL NUMBER OF THIS
EQUIPMENT BELOW. THE
Italiano
NUMBERS ARE ON THE TOP
PANEL.
MODEL NO. DR-U16S
SERIAL NO.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS KEEP THESE NUMBERS FOR
APPLIANCE TO RAIN OR MOISTURE.
FUTU
Summary of the content on the page No. 2
This product complies with the EMC Directives (89/336/EEC, 92/31/EEC) and CE Marking Directive (93/68/EEC). Ce produit est conforme aux directives relatives à la compatibilité électromagnétique (89/336/CEE, 92/31/CEE) et à la directive CE relative aux marquages (93/68/CEE). Dieses Produkt entspricht den EMV-Richtlinien (89/336/EEC, 92/31/EEC) und CE-Markierungsrichtlinien (93/68/EEC). Questo prodotto è conforme alle direttive EMC (89/336/CEE, 92/31/CEE) e alla direttiva sul marchio CE (93/68/CEE
Summary of the content on the page No. 3
SAFETY INSTRUCTIONS To ensure your personal safety and to maximize the full operating potential of your Drive, read and follow these safety precautions: ENVIRONMENT - Please do not use the unit at places with much dust, high temperature, or high humidity. Please use the unit at a place where it is not subjected to vibrations or shocks. POWER - Power-off your system and attached hardware devices before installation. READ INSTRUCTIONS - Read all safety and operating instructions before the Drive i
Summary of the content on the page No. 4
SAFETY INSTRUCTIONS RADIO SIGNAL INTERFERENCE - This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How
Summary of the content on the page No. 5
HOW TO USE THIS MANUAL The following conventions are used throughout the manual: Bold Type Bold lettering is used to emphasize the importance of a statement being made. Italics Italics are used when indicating a reference to another section in the manual and to emphasize a point. A triangle with an exclamation point is used as a Warning symbol. Warning bring attention to instructions that must be followed exactly. The check mark is used to note additional and pertinent information regarding an i
Summary of the content on the page No. 6
TABLE OF CONTENTS INTRODUCTION .......................................................................................................................................7 FEATURES……. ........................................................................................................................................7 SYSTEM REQUIREMENTS .......................................................................................................................8 OPERATING SYSTEM COMPATIBILTY............
Summary of the content on the page No. 7
INTRODUCTION Congratulations, you have purchased the most advanced CD-ROM drive in the world. This is a CD-ROM drive with built-in SCSI-2 specifications, and it must be used with a SCSI host adapter. This Manual was written to guide you through a simple and straight forward installation and operation of the product. For best results, we recommend that you review this manual before installing your CD-ROM Drive. In addition to installation instructions, this manual provides specifications, instruc
Summary of the content on the page No. 8
SYSTEM REQUIREMENTS OPERATING SYSTEM COMPATIBILITY The Drive is bundled with software drivers for MS-DOS/Windows systems, however, drivers for many other systems are also available. BASIC SYSTEM REQUIREMENTS: IBM PC/XT/AT/386 SYSTEMS 640 KB RAM 516 KB of Available Disk Space DOS Version 3.1 or higher SCSI Interface Card if your system dose not have one. Empty slot for drive expansion One Expansion Slot if a SCSI Interface Card is needed. SCSI Cable Power Cable INSPECTION CHECKLIST The Pioneer CD
Summary of the content on the page No. 9
A HARDWARE TOUR Illustrations are provided in this chapter as a visual introduction to the Drive. Please Familiarize yourself with these illustrations and refer to them when necessary to complete the installation and operation of the unit. Front View CD-ROM DRIVE 1 PHONES BUSY 6 5 4 3 2 Fig.1 1 Disc loading slot Insert the CD-ROM with the label facing up. PRECAUTIONS ON PLAYING CD SINGLES (8 cm Discs): ¦ When playing CD singles (8 cm discs), always use the adapter for 8 cm discs. Before loading
Summary of the content on the page No. 10
A HARDWARE TOUR Rear View The display is on the top panel. 49 1 DC INPUT 4 1 8 1 50 2 +5 G G +12 4 3 2 1 Fig.2 1 DC Input This is the input for DC +5 V and +12 V. Connect the computer power supply. 2 SCSI interface This is a 50-pin I/O connector according to the SCSI-2 specifications. Use a flat ribbon SCSI connector to connect to the SCSI host adapter. 3 Function switch Use the accessory short-circuit sockets to set the SCSI ID number and the drive function. 4 Audio output This is a connector f
Summary of the content on the page No. 11
INSTALLATION HARDWARE SETUP OVERVIEW This chapter describes the steps required to connect your Pioneer Drive to your PC. Prior to installation, there are a few things you should know about this product. ♦ First, the Drive is a SCSI device. What is a SCSI device? SCSI is an acronym for Small Computer System Interface. A SCSI system allows up to seven SCSI devices (including CD-ROM drives, hard disks, scanners, and tape drives) to be connected to each other in a series called a "daisy chain" A SCS
Summary of the content on the page No. 12
INSTALLATION SETTING THE SCSI ID SCSI devices are identified by a SCSI ID number from 0 through 7 with ID number 7 typically reserved for the SCSI interface card. The basic rule for assigning a SCSI ID number requires that: Each SCSI device have a unique ID number (address) on the SCSI bus. If two SCSI devices are assigned the same ID number, your computer will not operate properly. Assigning a SCSI ID to the Drive if you have a PC: To avoid conflicts with an existing SCSI device and the interfa
Summary of the content on the page No. 13
INSTALLATION SCSI TERMINATION SCSI termination is a technique used to absorb line reflections at the beginning and end of a SCSI daisy chain that would otherwise interfere with legitimate SCSI signals and cause errors. To minimize interference with data transfer, SCSI termination is absolutely required for proper operation of your Drive. WHEN TERMINATION IS REQUIRED If you are installing the Drive as the only SCSI device or as the last SCSI device in the chain, termination must be enabled. A bui
Summary of the content on the page No. 14
INSTALLATION SWITCH SETTING TABLE The display is on the top panel. 2048/512 TERMINATION (SHORT – OFF) DISABLE EJECT RESERVED Switch 4 - Reserved RESERVED SCSI ID MUST BE SET TO OFF (OPEN) 2 1 0 Switch 5: SCSI Terminator The built-in switch which enables or disables SCSI termination. Switch # 8 7 6 5 4 3 2 1 Short = SCSI Termination OFF : SCSI termination disabled (factory default setting). Open = SCSI Termination ON: SCSI termination enabled. Note: This in
Summary of the content on the page No. 15
CD-ROM DRIVE PHONES BUSY TO INSTALL THE DRIVE Fig.3 Ö Switch off the power of the personal computer and remove the cover or the front panel. Ö Remove the blank panel installed at the front of the 5.25 inch slot. Installation is not possible when there is no empty slot. Ö Install the fixation slide rails on the drive. (If slide rails are required, contact the shop where you bought the computer or the computer manufacturer.) Ö Insert the drive into the slot. Ö If fixing is required, fix the drive
Summary of the content on the page No. 16
CONNECTING THE DRIVE IN THE MIDDLE OF A SCSI CHAIN Sound Board DR - U16S Audio Cable SCSI HOST Pin 1 Adapter Pin 1 SCSI hard disk SCSI Interface Cable Into an expansion slot of the personal computer To the power supply of the personal computer Fig.4 When a SCSI hard disk or other SCSI equipment also is installed in the computer, please connect according to the following method. ¦ Switch off the power supply of the personal computer. ¦ Set the SCSI ID number so that it is different f
Summary of the content on the page No. 17
CONNECTING THE DRIVE AS THE ONLY SCSI DEVICE Sound Board Audio Cable SCSI HOST Pin 1 Adapter Power Cable SCSI Interface To the power supply of Cable the personal computer Into an expansion slot of the personal computer Fig.5 When no SCSI hard disk or other SCSI equipment is used, connect according to the following connection method. ¦ Switch off the power supply of the personal computer. ¦ Set the SCSI ID number. ¦ Set the termination ON. ¦ Connect the power supply cable from the pe
Summary of the content on the page No. 18
DISC OPERATION DISC SETTING METHOD ¦ Disc setting Insert the disc into the disc loading slot with the label facing up. When using 8 cm discs, attach a CD adapter (available at stores) to the disc, and insert the disc into the disc loading slot. 8 cm disc CD adapter Fig.6 Do not insert 8 cm discs by themselves. When using a CD adapter, attach it properly to the disc, and check that it does not come off to prevent damage to the disc and adapter. Do not attempt to insert more than two discs at on
Summary of the content on the page No. 19
DISC OPERATION DISC REMOVAL METHOD ¦ Confirm that the BUSY indicator of the drive is not lit, and then press the Eject button (0). ¦ Remove the disc after it has been ejected. Do not place anything within 12 cm in front of the unit as this may obstruct the disc ejection operation of the unit. CD-ROM DISC INFORMATION/FORMATS SUPPORTED ¦ High Sierra, CD-ROM XA, (Mode 2, Form 1 and 2), Rock Ridge and, CD-DA audio Discs. MEDIA DIAMETER ¦ 120 mm/12 cm/4.72" disc and 80 mm/8 cm/3.15" disc (always atta
Summary of the content on the page No. 20
DISC OPERATION DO NOT use non-standard discs, as these may adversely influence this unit and other equipment. DO NOT play a CD having other shape than a circular disc, such as heart shaped disc. Otherwise malfunction may occur. USING THE AUDIO FEATURES This unit has a function for playback of audio discs by itself. This is a function for audio playback without using computer software. ¦ Set an audio disc into the drive. ¦ When the Play/Skip button is pressed once, audio playback will be started
