Summary of the content on the page No. 1
DX7100 Hard Drive
Replacement Instructions
for the System Drive
C674M (2/06)
Digital Video Recorder
DX7100
Summary of the content on the page No. 2
Summary of the content on the page No. 3
Introduction This manual provides instructions for replacing the primary master hard drive in a DX7100 Series DVR (digital video recorder). PARTS LIST NOTE: This replacement kit includes a Pelco-certified hard disk drive. Using any other hard disk drive with the DX7100 voids the manufacturer's warranty for the DX7100. 1 120 GB hard disk drive 2 Mounting screws 1 DX7100-RPS software recovery CD Normally, after replacing the hard disk drive, your system should operate properly. However,
Summary of the content on the page No. 4
Installation WARNING: Any video on the primary master hard drive will be lost when the drive is replaced. To replace the primary master hard drive: 1. To protect the DVR and its components against electrostatic discharge, make sure that you are properly grounded so that any built-up static electric charges are dissipated away from the unit. The most effective way to do this is to use a properly grounded wrist strap. If a wrist strap is not available, you can discharge built-up static
Summary of the content on the page No. 5
4. Locate the hard drives in the front of the DVR (refer to Figure 2). There is one hard drive cage in the center front that can hold as many as four hard drives. There is another against the side of the chassis that can hold as many as two hard drives. The top hard drive in the two-drive cage is the primary master that will be replaced. HARD DRIVES Figure 2. Locating the Hard Drives C674M (2/06) 5
Summary of the content on the page No. 6
5. Remove the cage that holds four hard drives: a. Disconnect the power and data cables from any hard drives that are installed in the cage. b. Remove the two screws that hold the cage in place in the chassis (refer to Figure 3). c. Disconnect the ground wire that goes to the card cage (refer to Figure 4). d. The card cage is locked in place in the bottom of the chassis. To unlock the card cage, slide the card cage about a half inch toward the back of the chassis (refer to Figure 3). Li
Summary of the content on the page No. 7
6. Remove the card cage that holds two hard drives (refer to Figure 5): a. Disconnect the power and data cables from the hard drives that are installed in the cage. b. Remove the three screws that hold the cage in place in the chassis. c. The card cage is locked in place in the bottom of the chassis. To unlock the card cage, slide the card cage about a half inch toward the back of the chassis and then about a half inch toward the location where the four- position hard drive cage was insta
Summary of the content on the page No. 8
7. Remove the two screws on each side of the cage that hold the primary master drive in place (refer to Figure 6). Remove the hard disk drive. SCREWS Figure 6. Removing the Hard Disk Drive 8. Verify that the jumper on the replacement hard drive is set for master. Refer to Figure 7. JUMPER Figure 7. Jumper Placement 9. Replace the hard drive. 8 C674M (2/06)
Summary of the content on the page No. 9
WARNING: When you reinstall the hard drive cages, make sure that no wiring is underneath the cages. 10. Reinstall the hard drive cages by following steps 2-7 in reverse order. Refer to Figure 8 to see how the cages are locked in place in the bottom of the chassis. Figure 8. Reinstalling the Hard Drive Cages C674M (2/06) 9
Summary of the content on the page No. 10
Summary of the content on the page No. 11
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective If a warranty repair is required, the Dealer must contact Pelco at in material or workmanship for a period of one year after the date of (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number shipment. (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial numb
Summary of the content on the page No. 12
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East | | | | | | | |
