Summary of the content on the page No. 1
HARD DRIVE
PRODUCT
MANUAL
™
DiamondMax Plus 5120
92048U8, 91792U7, 91536U6
91280U5, 91024U4, 90750U3
Summary of the content on the page No. 2
DiamondMax™ Plus 5120 92048U8, 91792U7, 91536U6, 91280U5, 91024U4 and 90750U3 Part #1412/B All material contained herein Copyright © 1999 Maxtor Corporation. DiamondMax™, DiamondMax™ 4320, DiamondMax™ Plus 2500, DiamondMax™ Plus 5120 and MaxFax™ are trademarks of Maxtor ® Corporation. No Quibble Service is a registered trademark of Maxtor Corporation. Other brands or products are trademarks or registered trademarks of their respective holders. Contents and specifications subject to change withou
Summary of the content on the page No. 3
Revisions Manual No. 1412 R. EVEN C NOSN ECTIO DESCRIPTIO DATE A97l 944A. l Initial release 05/12/99 B473 955 2-2, 3-1, 3- Power and areal density specifications updated; UDMA 66 drawing added. 06/24/99 and 5-1
Summary of the content on the page No. 4
Before Y ou Begin Thank you for your interest in the Maxtor DiamondMax™ Plus 5120 AT hard disk drives. This manual provides technical information for OEM engineers and systems integrators regarding the installation and use of DiamondMax hard drives. Drive repair should be performed only at an authorized repair center. For repair information, contact the Maxtor Customer Service Center at 800-2MAXTOR or 408-922-2085. Before unpacking the hard drive, please review Sections 1 through 4. CAUTION Maxt
Summary of the content on the page No. 5
DIAMONDMAX PLUS 5120 PRODUCT MANUAL Contents Section 1 — Introduction Maxtor Corporation 1 - 1 Products 1 - 1 Support 1 - 1 Manual Organization 1 - 1 Abbreviations 1 - 1 Conventions 1 - 2 Key Words 1 - 2 Numbering 1 - 2 Signal Conventions 1 - 2 Section 2 — Product Description The DiamondMax™ Plus 5120 Product Features 2 - 2 Functional/Interface 2 - 2 Zone Density Recording 2 - 2 Read/Write Multiple Mode 2 - 2 UltraDMA - Mode 4 2 - 2 Multi-word DMA (EISA Type B) - Mode 2 2 - 2 Sector Address Tran
Summary of the content on the page No. 6
DIAMONDMAX PLUS 5120 PRODUCT MANUAL Section 3 — Product Specifications Models and Capacities 3 - 1 Drive Configuration 3 - 1 Performance Specifications 3 - 1 Physical Dimensions 3 - 2 Power Requirements 3 - 3 Power Mode Definitions 3 - 3 Spin-up 3 - 3 Seek 3 - 3 Read/Write 3 - 3 Idle 3 - 3 Standby 3 - 3 Sleep 3 - 3 EPA Energy Star Compliance 3 - 3 Environmental Limits 3 - 3 Shock and Vibration 3 - 4 Reliability Specifications 3 - 4 Annual Return Rate 3 - 4 Quality Acceptance Rate 3 - 4 Start/Sto
Summary of the content on the page No. 7
DIAMONDMAX PLUS 5120 PRODUCT MANUAL Ultra Direct Memory Access (UDMA) 4 - 5 OS Requirements for Large Capacity Hard Drives 4 - 5 Hard Drive Identification 4 - 6 Identifying IDE Devices on the Interface 4 - 6 Jumper Settings 4 - 6 Systems Using Cable Select 4 - 6 Relationship to Other IDE Devices 4 - 6 Mounting Drive in System 4 - 7 Attaching Interface and Power Cables 4 - 7 Attaching System Cables 4 - 7 System Setup 4 - 8 Setting the BIOS (CMOS) 4 - 8 BIOS (CMOS) Parameters 4 - 8 Hard Drive Prep
Summary of the content on the page No. 8
DIAMONDMAX PLUS 5120 PRODUCT MANUAL Device Control Register 6 - 5 Digital Input Register 6 - 5 Reset and Interrupt Handling 6 - 6 Section 7 — Interface Commands Command Summary 7 - 1 Read Commands 7 - 2 Read Sector(s) 7 - 2 Read Verify Sector(s) 7 - 2 Read Sector Buffer 7 - 2 Read DMA 7 - 3 Read Multiple 7 - 3 Set Multiple 7 - 3 Write Commands 7 - 4 Write Sector(s) 7 - 4 Write Verify Sector(s) 7 - 4 Write Sector Buffer 7 - 4 Write DMA 7 - 5 Write Multiple 7 - 5 Ultra DMA 7 - 5 Set Feature Comman
Summary of the content on the page No. 9
DIAMONDMAX PLUS 5120 PRODUCT MANUAL Figures Figure Title Page 2 - 1 PCBA Jumper Location and Configuration 2 - 6 3 - 1 Outline and Mounting Dimensions 3 - 2 4 - 1 Multi-pack Shipping Container 4 - 2 4 - 2 Single-pack Shipping Container (Option A) 4 - 3 4 - 3 Single-pack Shipping Container (Option B) 4 - 3 4 - 4 Master, Slave and Cable Select Settings 4 - 5 4 - 5 5.25-inch Mounting Brackets and Rails 4 - 6 4 - 6 IDE Interface and Power Cabling Detail 4 - 7 4 - 7 Master, Slave and Cable Select Jum
Summary of the content on the page No. 10
DIAMONDMAX PLUS 5120 – INTRODUCTION SECTION 1 Introduction Maxtor Corporation Maxtor Corporation has been providing high-quality computer storage products since 1982. Along the way, we’ve seen many changes in data storage needs. Not long ago, only a handful of specific users needed more than a couple hundred megabytes of storage. Today, downloading from the Internet and CD-ROMs, multimedia, networking and advanced office applications are driving storage needs even higher. Even home PC applicatio
Summary of the content on the page No. 11
DIAMONDMAX PLUS 5120 – INTRODUCTION Conventions If there is a conflict between text and tables, the table shall be accepted as being correct. Key Words The names of abbreviations, commands, fields and acronyms used as signal names are in all uppercase type (e.g., IDENTIFY DRIVE). Fields containing only one bit are usually referred to as the “name” bit instead of the “name” field. Names of drive registers begin with a capital letter (e.g., Cylinder High register). Numbering Numbers that are not f
Summary of the content on the page No. 12
PRODUCT DESCRIPTION SECTION 2 Product Description Maxtor DiamondMax™ Plus 5120 AT disk drives are 1-inch high, 3.5-inch diameter random access storage devices which incorporate an on-board ATA-5/Ultra DMA controller. High capacity is achieved by a balanced combination of high areal recording density and the latest data encoding and servo techniques. Maxtor's latest advancements in electronic packaging and integration methods have lowered the drive's power consumption and increased its reliabilit
Summary of the content on the page No. 13
PRODUCT DESCRIPTION Product Features Functional / Interface Maxtor DiamondMax™ Plus 5120 hard drives contain all necessary mechanical and electronic parts to interpret control signals and commands from an AT-compatible host computer. See Section 3 Product Specifications, for complete drive specifications. Zone Density Recording The disk capacity is increased with bit density management – common with Zone Density Recording. Each disk surface is divided into 16 circumferential zones. All tracks wi
Summary of the content on the page No. 14
PRODUCT DESCRIPTION Logical Block Addressing The Logical Block Address (LBA) mode can only be utilized in systems that support this form of translation. The cylinder, head and sector geometry of the drive, as presented to the host, differs from the actual physical geometry. The host AT computer may access a drive of set parameters: number of cylinders, heads and sectors per track, plus cylinder, head and sector addresses. However, the drive can’t use these host parameters directly because of zon
Summary of the content on the page No. 15
PRODUCT DESCRIPTION Cache Management Buffer Segmentation The data buffer is organized into two segments: the data buffer and the micro controller scratch pad. The data buffer is dynamically allocated for read and write data depending on the commands received. A variable number of read and write buffers may exist at the same time. Read-Ahead Mode Normally, this mode is active. Following a read request, disk read-ahead begins on the first sector and continues sequentially until the allocated buffe
Summary of the content on the page No. 16
PRODUCT DESCRIPTION Major HDA Components Drive Mechanism A brush-less DC direct drive motor rotates the spindle at 7,200 RPM (±0.1%). The dynamically balanced motor/spindle assembly ensures minimal mechanical run-out to the disks. A dynamic brake provides a fast stop to the spindle motor upon power removal. The speed tolerance includes motor performance and motor circuit tolerances. Rotary Actuator All DiamondMax™ Plus 5120 drives employ a rotary voice coil actuator which consists of a moving co
Summary of the content on the page No. 17
PRODUCT DESCRIPTION Subsystem Configuration Dual Drive Support Two drives may be accessed via a common interface cable, using the same range of I/O addresses. The drives are jumpered as device 0 or 1 (Master/Slave), and are selected by the drive select bit in the Device/Head register of the task file. All Task File registers are written in parallel to both drives. The interface processor on each drive decides whether a command written to it should be executed; this depends on the type of command
Summary of the content on the page No. 18
PRODUCT SPECIFICATIONS SECTION 3 Product Specifications Models and Capacities MODEL 97 2048U896 1792U95 1536U94 1280U93 1024U 90750U Formatted Capacity (MB LBA Mode)20 0,48010 7,9210 5,3610 2,80 17 0,24 ,0 50 6 9 Maxtor defines one megabyte as 10 or one million bytes and one gigabyte as 10 or one billion bytes. Drive Configuration M8 ODEL 97 2048U96 1792U95 1536U94 1280U93 1024U 90750U Integrated Controller / Interface ATA-5 / Ultra DMA Encoding Method EPR4 RLL 16/17 I1 nterleave 1: Servo System
Summary of the content on the page No. 19
PRODUCT SPECIFICATIONS Physical Dimensions PD ARAMETERSC TANDAR METRI Hs eight1s .02 inche 25.9 millimeter Ls ength5s .78 inche 146.6 millimeter Ws idth4s .00 inche 102.1 millimeter Ws eight1s .3 pound 0.59 kilogram 1.028 max [25.9 mm] 6 x 6-32 1.638 ± .005 1.122 ± .02 .25 ± .01 UNC Tap [41.61 mm] [28.4 mm] 4.000 ± .01 [101.6 mm] 5.787 max [146.6 mm] 4 x 6-32 1.75 ± .02 1.625 ± .02 UNC Tap 4.00 ± .01 [102.1 mm] 3.75 ± .01 [95.25 mm] Figure 3 - 1 Outline and Mounting Dimensions 3 – 2
Summary of the content on the page No. 20
PRODUCT SPECIFICATIONS Power Requirements (Average) M% ODE 1% 2V ± 105R V ± 5 POWE Spin-up (peak)2A 440 mA 360 m SA eek 9A 49 m 4W 31 m 13.5 RA ead/Write 4A 13 m 4W 50 m 7.2 IA dle 4A 10 m 3W 92 m 6.9 SA tandby 2A 3 m 2W 20 m 1.4 SA leep 2A 1 m 1W 47 m 1.0 Power Mode Definitions Spin-up The drive is spinning up following initial application of power and has not yet reached full speed. Seek A random access operation by the disk drive. Read/Write Data is being read from or written to the drive. Id
