Summary of the content on the page No. 1
Gigabit Lan
+ USB2.0 PCI Host
User Manual
English
LINDY No. 70570
www.LINDY.com
© LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (November 2004)
Summary of the content on the page No. 2
1. Introduction This PCI Host Adapter is a PCI controller board which can upgrade your desktop computer to have Gigabit Ethernet (1000Mbps, 100 Mbps, 10 Mbps) and three USB2.0 / USB1.1 ports. The board supports a 32-bit 33 MHz PCI bus revision 2.2, USB transfer rate of 1.5Mb/s, 12Mb/s, 480Mb/s and Gigabit Ethernet 10/100/1000Base-T. This Low Profile Form factor can support Low profile PCI and regular PCI both. It comes with drivers for Windows. 1.1. Features 1.1.1. PCI Inte
Summary of the content on the page No. 3
o Wake-on-LAN and remote wake-up support o Microsoft® NDIS5 Checksum Offload (IP, TCP, UDP) and largesend offload support o Supports Full Duplex flow control (IEEE 802.3x) o Supports IEEE 802.1Q VLAN tagging o 8K Transmit FIFO and 64K Receive FIFO support o Supports power down/link down power saving 1.1.3. USB Interface Provides three USB2.0 / USB1.1 ports (2 External + 1 Internal). Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate 1.5/12/480 Mbps). C
Summary of the content on the page No. 4
5. During OS boot up, all necessary USB drivers will be detected and installed automatically. 6. Windows will display the Found New Hardware Wizard, “Ethernet controller”, Click “Next”. 7. Select “Search for a suitable driver for my device (Recommended)” and Click “Next”, and make sure the Driver CD in your CD-ROM/DVD. 8. Under “Specify a locations” insure that is only checked, and click “Next”. 9. Type in E:\ (If your CD-ROM/DVD is E:\) and click “Browse”. 10. Points specify a location,
Summary of the content on the page No. 5
“Next”. Then click “Finish”. 2.3.Verifying the installation under Windows 2000 and XP Follow the instructions in this section to verify that the controller was installed correctly. 1. Right click on “My Computer” icon, select “Properties”, left click on “Hardware” tab, and then on “Device Manager” button. 2. Double click “Universal Serial Bus Controllers”, If there is no yellow “!” or “?” in front of NEC PCI to USB Open Host controller NEC PCI to USB Open Host controller
Summary of the content on the page No. 6
and click “Next”. 8. Select “Search for the best driver for your device(Recommended)”. Click “Next”. 9. Select “Floppy disk drives” and uncheck the other boxes and click “Next”, Select “The Updated driver (Recommended)” NEC USB Open Host Controller, and click “Next”, then click “Next” to continue. 10. If display “Insert Disk” (please insert the disk labeled windows 98 second Edition CD-ROM) and click OK, Then click “Finish” to exit the wizard, and Remove your Windows 98 second Edi
Summary of the content on the page No. 7
3. Make sure “Search for the best driver for your device (Recommended)”, and “Specify a location are both selected, uncheck the other boxes, and type in E:\ (If your CD-ROM/DVD is E:\) and click “Browse”. 4. Points specify a location, example E:\USB2.0 Host\NEC\Win98_me. Click “OK”, and click “Next”. (If your CD-ROM/DVD drive is E:) 5. When the wizard indicates that it found a driver for the device, click “Next”. Then click “Finish” to exit the wizard. 6. The Hardware Wizard will display
Summary of the content on the page No. 8
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operations. - 8 -
