Summary of the content on the page No. 1
OEM Manual
Hard Disk Drive Specifications
Ultrastar 15K73-73/36
(SCSI)
Models HUS157373EL3600 :(73GB/68pin)
(
Models HUS157336EL3600 : 36GB/68pin)
(
Models HUS157373EL3800 : 73GB/80pin)
(
Models HUS157336EL3800 : 36GB/80pin)
Read and follow all instructions and cautions for safety described
in this document before using the drive.
It is recommended that this manual is kept at a proper location
for quick reference.
Hitachi Global Storage Technologies
© 2003, Hitachi Global Storage Tec
Summary of the content on the page No. 2
REVISION CONTROL Remarks AD: Addition , CH: Change ,CR: Correction ,DL: Deletion Rev. Date Signature Page Description Remarks 2002/11/5 DWN : O,Suzuki 0 All First Issuance CHKD: - APPD: - 2003/1/17 DWN : O,Suzuki 1 3-5 Safety cautions were moved before CH CHKD: - table of contents. APPD: - 11 Seek time, Power requirement CH Power dissipation 27 9.3 Storage CH 2003/2/7 DWN : O,Suzuki 2 1 Model Name CR CHKD: - 11 Acoustic noise CR APPD: - 2003/3/28
Summary of the content on the page No. 3
To use this product safely Read and follow all instructions and cautions described in this chapter before using the drive. It is recommended that this manual is kept at a proper location for quick reference. The description related to safety in this chapter may be changed without notice. Influence for environment Although this product emits electro-magnetic field, it will be found to be in compliance with the EMI regulations such as VCCI class B, FCC Part 15 class B. However, anything other than
Summary of the content on the page No. 4
To use this product safely (Continued) Followings are the cautions and contents described in this manual. Caution Items of indicating : - Safety cautions for this product Page 4 Caution Items of indicating : - Safety cautions for this product Page 4-5 - Spindle Start and Stop Page 16 - Mounting of the drive Page 24 - Reliability temperature Page 26 - Precautions for handling Page 27 Safety cautions for this product Caution 0.2.1 This product is not authorized for use
Summary of the content on the page No. 5
To use this product safely (Continued) Caution 0.2.11 Protect the drive against shocks with the corrugated board and cushioning material provided by the manufacturer, or with Hitachi Approved containers. 0.2.12 When mounting the drive, use the size of screws and the torque recommended in this manual. If non-recommended size of screws and torque are used, it may cause catastrophic failures. 0.2.13 Do not press top cover and bottom PCB of the drive. It may cause catastrophic failures. 0.2.14 Read
Summary of the content on the page No. 6
TABLE OF CONTENTS Chapter Page To use this product safely.................................................................................. 3 1 Features............................................................................................................... 8 2 Standards and Related Documents.................................................................. 9 3 Description .......................................................................................................... 10 3.1
Summary of the content on the page No. 7
11 Pin assignment.................................................................................................... 33 11.1 SCSI Bus Connector C1...................................................................... 33 11.2 Other connectors................................................................................... 37 12 Jumper Socket setting........................................................................................ 39 12.1 Jumper connector layout...........................
Summary of the content on the page No. 8
1 Features The Ultrastar 15K73 series uses high performance sputtered disks, GMR heads, and a rotary type voice coil motor to drive the heads. These features provide high capacity, high speed positioning and high reliability. The Ultrastar 15K73 series uses a SCSI interface for data transfer. Related ANSI Specifications are as follows. ANSI X3.301-1997 (SCSI-3 Primary Commands) X3T10/995D Rev 11a (SCSI-3 Primary Commands) X3T10/996D Rev 8c (SCSI-3 Block Commands) X3T10/1142D Rev 20a (SCSI Parall
Summary of the content on the page No. 9
2 Standards and Related Documents (a) Safety standards It is the user’s responsibility to assure the actual system in which the drive is installed meets the appropriate safety requirements. However, the drive was tested to be in compliance with the following standards: UL 1950 3rd Edition CAN/ CSA C22.2-M95 IEC 60950: 1991 EN60950: 1992 (b) Regulations related to electro-magnetic compatibility It is the user’s responsibility to assure the actual system in which the drive is installed meets the a
Summary of the content on the page No. 10
3 Description 3.1 Characteristics Table 3.1 Characteristics Item Specifications Ultrastar 15K73-73 Ultrastar 15K73-36 unit Configuration Storage capacity 73.9 36.9 GB (formatted) (see Note 1,2,13) Bytes/sector (see Note 3) 512, 516, 520, 524, 528,1024 Bytes Number of disks 5 3 Number of heads 10 5 2 Areal density 31.2 Gb/inch Recording method MEEPRML Performance Seek time average 3.9 / 4.2 ms read / write full stroke 7.2 / 8 ms (see Note 5) 1 track 0.4 / 0.5 ms Average latency 1.99 m
Summary of the content on the page No. 11
3.2 Environmental conditions and reliability Table 3.2 Environmental conditions and reliability Item Ultrastar 15K73-73 Ultrastar 15K73-36 Environmental operating 5 to 55°C conditions Temperature non-operating -40 to 70°C storage/shipping -40 to 70°C Temperature gradient 20°C per hour maximum Humidity operating 5 to 90%RH non-operating 5 to 90%RH Wet bulb temperature 29°C maximum (non condensing) Atmosphere No corrosive gas, saline atmosphere or organic-metal compound (Example. organic silicon
Summary of the content on the page No. 12
Note 1. Storage capacity does not include spare sector and spare cylinder. Note 2. This is the value in the case that the drive is formatted to 512 Bytes/sector. 9 (1 gigabyte shows 1x10 bytes on this document.) Note 3. Ultrastar 15K73 is formatted to 512 Bytes/sector as the default. If non-512 Bytes/sector is required, customer can change it by re-format of the drive. Note 4. Data transfer rate is degraded with cable or host condition or electrical noise. Note 5. These specifications are t
Summary of the content on the page No. 13
Note 7. The disk drive orientation for shock shown in Figure 4.2. test is Figure 3.2 Shock test direction Test conditions on shock test are as follows. (1) Operating 2 147m/s (15G) (Shock mode: half sine wave 11 ms, Test cycle: 5 times) (2) Non-operating 2 735m/s (75G) (Shock mode: half sine wave 11 ms, Test cycle: 5 times) 2 2450m/s (250G) (Shock mode: half sine wave 2 ms, Test cycle: 5 times) Note 8. Acoustic noise is measured except for the start, stop and seek operations. Drawing No. She
Summary of the content on the page No. 14
Note 9. Recoverable error is measured at the nominal condition with voltage, temperature and default error recovery parameters. Note 10. The drive should be mounted properly (see section 8). Note 11. MTBF represents a prediction of performance based upon a large statistical sample calculated in accordance with Hitachi's standard procedures. Hitachi does not warrant that the predicted MTBF is representative of any particular unit or group of units comprising a customer base. The actual failure r
Summary of the content on the page No. 15
4 DC power Interface 4.1 DC Power Requirement The drives are operated on DC power (+5V, +12V) only. No power sequencing is required. The +5 and +12 Volts can be applied in any order. Table 4.1 DC Power Requirement Power supply Voltage tolerance Allowed ripple and noise +5V DC 5.0V +/-5% Less than 150mVp-p (0 - 100kHz) Less than 100mVp-p (100kHz - 10MHz) +12V DC 12.0V +/-5% Less than 150mVp-p (0 - 100kHz) Less than 100mVp-p (100kHz - 10MHz) Note 1. Voltage tolerance is measured at the DC po
Summary of the content on the page No. 16
4.2 Power supply current +12V Current [A] 3.0 Peak 2.0 1.0 0 4 6 8 10 12 14 16 18 20 0 2 Time [s] T0 T1 T2 T3 T4 T0-T1: Power up T0 : Power on T1-T2: Spin-up T1 : Accept start unit command or Auto Spin-up T4 :Ready T2-T3: Servo initialize T3-T4: Upload Code etc. T1-T4: Start up Fig 4.1 Current transition for +12V Note: A retry Spin-up operation may be attempted during the Start up process. 4.3 Spindle Start and Stop 4.3.1 Start and Stop Time Table 4.2 Start and St
Summary of the content on the page No. 17
4.3.2 Spindle Start Selection When multiple disk drives are connected to the same power supply and turned on simultaneously, a large current will be required at power up. In the above case, it is recommended to turn the motors on one by one at intervals in order to minimize 12V line current. This can be done according to the following 3 jumper pin configurations in the case of NW drive: 1. If Disable Auto Start mode is set (C3:9-10 installed); (1) Use a spindle start command for each drive, issu
Summary of the content on the page No. 18
5 Connecting Methods 5.1 Interface Cable (Daisy Chain) Terminator SCSI interface cable Terminator SCSI bus Ultrastar Ultrastar Ultrastar 15K73 15K73 15K73 DC power power supply cable GND Figure 5.1 Cabling layout (WIDE LVD drive) Note 1. The SCSI bus can accommodate a maximum of 16 units on a WIDE (16-bit) bus, including the host processor, Ultrastar 15K73 units, and other SCSI devices. Note 2. The WIDE LVD and SCA-2 LVD drives do not have the terminator on the drive, so an external t
Summary of the content on the page No. 19
5.2 Low voltage differential (LVD) mode The NW and NC drives have two different transceivers to allow customer to use it in traditional systems which may use single-ended drivers and receivers, or to use it in low voltage differential (LVD) systems which use LVD drivers and receivers. Their I/O circuits are selectable using the I/O "DIFFSENS" line. When the I/O "DIFFSENS" line is between -0.35V and +0.5V, the drive interface circuits operate single-ended. When "DIFFSENS" is between +0.7V and +1.
Summary of the content on the page No. 20
6 SCSI Interface 6.1 Summary of SCSI Controller The Ultrastar 15K73 SCSI controller interfaces between the drive and the host computer with the Small Computer System Interface (SCSI). (1) ANSI standard The controller supports the SCSI interface that conforms to the ANSI specifications shown in section 2. (2) Compact design The controller is embedded within the disk drive. (3) Fast data transfer rate The controller can transfer data via asynchronous mode, Fast-5 synchronous mode, Fast-10 synchro
