Summary of the content on the page No. 1
C141-F071-01EN
MHV2100AH, MHV2080AH
MHV2060AH, MHV2040AH
DISK DRIVE
MAINTENANCE MANUAL
Summary of the content on the page No. 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual.
Summary of the content on the page No. 3
Revision History (1/1) Edition Date Revised section (*1) Details (Added/Deleted/Altered) 01 2004-11-15 — — *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C141-F071
Summary of the content on the page No. 4
This page is intentionally left blank.
Summary of the content on the page No. 5
Preface This manual describes the MHV2100AH, MHV2080AH, MHV2060AH, MHV2040AH 2.5-inch hard disk drive with a built-in controller that is compatible with the ATA interface. This manual explains, in detail, how to maintain the disk drives. This manual assumes that users have a basic knowledge of hard disk drives and their application in computer systems. This manual consists of the following two chapters: Overview of Manual CHAPTER 1 Maintenance and Diagnosis This chapter explains MHV21
Summary of the content on the page No. 6
Preface In the text, the alert signal is centered, followed below by the indented message. A wider line space precedes and follows the alert message to show where the alert message begins and ends. The following is an example: (Example) Don’t install or remove a PCA or connect or disconnect a cable or connector plug when the drive is powered. This may give you an electric shock. The main alert messages in the text are also listed in the “Important Alert Items.” Operating Environmen
Summary of the content on the page No. 7
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: This manual uses the key alert messages given below. The following manual also contains notes on safety precautions: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the predate or other property, may occur if the user does not perform the procedure correctly. Task Alert message
Summary of the content on the page No. 8
Important Alert Items Task Alert message Page Maintenance Device damage 1. Before touching a PCA or the drive, wear a wrist strap 1-2 and perform the human body grounding to discharge static electricity from your body. This will prevent irreparable damage to the PCA and the head of the drive. 2. Don’t install or remove a PCA or connect or disconnect a cable or connector plug when the drive is powered. This will prevent electrical damage to the disk drive. 3. Operating the disk dri
Summary of the content on the page No. 9
Important Alert Items Task Alert message Page Maintenance Damage or Device damage 1. Perform any removal after the system power is 2-2 completely disconnected. The cable must not be disconnected and the screws that attach the drive must not be removed with the power ON. 2. Do not move the drive and attach or detach the connector until it comes to a complete stop (about 30 s after the power is turned OFF). 3. Perform the human body grounding to discharge any static electricity fro
Summary of the content on the page No. 10
This page is intentionally left blank.
Summary of the content on the page No. 11
Manual Organization MHV2100AH, MHV2080AH 1. Device Overview MHV2060AH, MHV2040AH 2. Device Configuration 3. Installation Conditions DISK DRIVE 4. Theory of Device Operation PRODUCT MANUAL 5. Interface (C141-E217) 6. Operations MHV2100AH, MHV2080AH 1. Maintenance and Diagnosis MHV2060AH, MHV2040AH 2. Removal and Replacement Procedure DISK DRIVE MAINTENANCE MANUAL C141-F071 vii
Summary of the content on the page No. 12
This page is intentionally left blank.
Summary of the content on the page No. 13
Contents CHAPTER 1 Maintenance and Diagnosis .....................................................1-1 1.1 Maintenance..........................................................................................1-2 1.1.1 Rules for maintenance......................................................................... 1-2 1.1.2 Maintenance requirements..................................................................1-3 1.1.3 Maintenance levels....................................................
Summary of the content on the page No. 14
Contents Illustrations Figures Figure 1.1 Disk drive revision number label................................................1-6 Figure 1.2 Display of disk drive revision number........................................1-7 Figure 1.3 Test flowchart..............................................................................1-9 Tables Table 1.1 Status register contents..............................................................1-10 Table 1.2 Disposition for error register contents .........
Summary of the content on the page No. 15
CHAPTER 1 Maintenance and Diagnosis 1.1 Maintenance 1.2 Operation Confirmation 1.3 Troubleshooting Procedure This chapter describes the maintenance, diagnosis, operation check, and troubleshooting of the disk drive. The following are explained: • Rules for regular maintenance and troubleshooting • Display of maintenance level (field and factory) • Display of machine revision number and number change in the field • Tools and test devices needed for each maintenance level •
Summary of the content on the page No. 16
Maintenance and Diagnosis 1.1 Maintenance 1.1.1 Rules for maintenance The following cautions must be observed to prevent injury during troubleshooting or maintenance. Static, Damage 1. Don’t install or remove a PCA or connect or disconnect a cable or connector plug when the drive is powered. This may give you an electric shock. 2. Keep away from mechanical assemblies in the unit during operation. This may cause injuries. 3. Avoid dangerous detergent when the disk drive is cleaned.
Summary of the content on the page No. 17
1.1 Maintenance 1.1.2 Maintenance requirements (1) Preventive maintenance The disk drive needs no preventive maintenance, not even the air filter needs to be changed. Device damage The DE is completely sealed. Do not open the DE in the field. (2) Service life In situations where management and handling are correct, the life of the disk drive is five years when the DE surface temperature is less than 48°C. When the DE surface temperature exceeds 48°C, the life is five years or 20,
Summary of the content on the page No. 18
Maintenance and Diagnosis Data corruption When asking for repair, save all data stored in the disk drive beforehand. Fujitsu Limited is not responsible for any loss of data during service and repair. (5) Notes on handling a. General notes a) Vibrations and shocks more severe than allowed will cause fatal damage to the device so be very careful. Be especially careful when unpacking the device. b) Do not leave the device in a dusty environment. c) Because the device uses GMR (giant
Summary of the content on the page No. 19
1.1 Maintenance b) It is recommended that you use the shock absorption cushion material and packaging that contained the device when it was delivered by Fujitsu. If the same packaging material cannot be used, use a shock absorbent box that will transmit shocks directly to the device. When using this type of box, adequately protect the PCA surface and interface connector section. c) Place a label showing which side is up and clearly stating the notes on handling on the outside of the pa
Summary of the content on the page No. 20
Maintenance and Diagnosis 1.1.4 Disk drive revision number The disk drive revision number is a single alphabetic character followed by a single alphanumeric character. It is stuck on the DE and marked on the revision number label. Figure 1.1 shows the disk drive revision number label format. Disk drive revision number Firmware code/revision Figure 1.1 Disk drive revision number label (1) Revision number marking at delivery The machine revision number is indicated by crossing out up
