Summary of the content on the page No. 1
C141-E234-01EN
MAX3147FC
MAX3073FC
MAX3036FC
HARD DISK DRIVES
PRODUCT/MAINTENANCE MANUAL
Summary of the content on the page No. 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. IM
Summary of the content on the page No. 3
Caution This computer device shall meet FCC Class A environment. If you use this device at Home environment, it may affect to the Television set, Radio receiver, and so on. In this case, you may require to take action to resolve any affection due to this device. The contents of this manual may be revised without prior notice. The contents of this manual shall not be disclosed in any way or reproduced in any media without the express written permissio
Summary of the content on the page No. 4
This page is intentionally left blank.
Summary of the content on the page No. 5
REVISION RECORD Edition Date published Revised contents 01 June, 2005 Specification No.: C141-E234-**EN C141-E234
Summary of the content on the page No. 6
Related Standards Product specifications and functions described in this manual comply with the following ANSI (*1) standards. Document number Title NCITS TR-19 FIBRE CHANNEL PRIVATE LOOP SCSI DIRECT ATTATH (FC-PLDA) ANSI X3.230-1994 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE (FC-PH) ANSI X3.297-1996 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE-2 (FC-PH-2) ANSI X3.272-199X FIBRE CHANNEL ARBITRATED LOOP (FC-AL) ANSI X3.269-199X FIBRE CHANNEL PROTOCOL FOR SCSI (SCSI-FCP) *1 A
Summary of the content on the page No. 7
Preface This manual describes the MAX3147FC, MAX3073FC, and MAX3036FC 3.5" type hard disk drives with an embedded fibre channel controller. This manual details the specifications and functions of the above disk drive, and gives the requirements and procedures for installing it into a host computer system. This manual is written for users who have a basic understanding of hard disk drives and their use in computer systems. The MANUAL ORGANIZATION section describes organization and scop
Summary of the content on the page No. 8
Preface APPENDIX A Connector Signal Allocation The appendix gives supplementary information, including the signal assignments of interface connectors. CONVENTIONS USED IN THIS MANUAL The MAX3147FC, MAX3073FC, and MAX3036FC disk drives are described as "the hard disk drive (HDD)", "the disk drive" or "the device" in this manual. Decimal number is represented normally. Hexadecimal number is represented as X'17B9', 17B9h or 17B9H. Binary number is represented as "010". Conventions for
Summary of the content on the page No. 9
Preface Attention Please forward any comments you may have regarding this manual. To make this manual easier for users to understand, opinions from readers are needed. Please write your opinions or requests on the Comment at the back of this manual and forward it to the address described in the sheet. C141-E234 iii
Summary of the content on the page No. 10
This page is intentionally left blank.
Summary of the content on the page No. 11
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Specification Data loss The drive adopts Reed-Solomon code for ECC. The sector-data is 2-5 divided into 3 int
Summary of the content on the page No. 12
Important Alert Items Task Alert message Page Installation Damage 1. When dismounting the drive which is mounted on the system while 5-16 power is supplied to it. • The drive to be dismounted must be separated from the loop. Dismounting the drive which is not separated from the loop may cause an unexpected error. • If the drive is not separated from the loop, issue an LPB to the drive from the initiator in a primitive sequence of the order set. • It is recommended to stop the spi
Summary of the content on the page No. 13
Important Alert Items Task Alert message Page Diagnostics and Caution Maintenance 1. Always ground yourself with a wrist strap connected to ground 6-5 before handling. ESD (Electrostatics Discharge) may cause the damage to the device. 2. Do not remove a PCA. This operation is required to prevent unexpected or unpredictable operation. 3. Do not use a conductive cleaner to clean a disk drive assembly. Damage 1. Never remove any labels from the drive. 6-14 2. Never open the d
Summary of the content on the page No. 14
This page is intentionally left blank.
Summary of the content on the page No. 15
MANUAL ORGANIZATION PRODUCT/ 1. General Description MAINTENANCE MANUAL 2. Specifications 3. Data Format (This manual) 4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 7. Error Analysis FIBRE CHANNEL 1. Fibre Channel Interface INTERFACE 2. Command Processing SPECIFICATIONS 3. Data Buffer Management 4. Command Specifications 5. Sense Data and Error Recovery Methods 6. Disk Media Management C141-E234 ix
Summary of the content on the page No. 16
This page is intentionally left blank.
Summary of the content on the page No. 17
CONTENTS CHAPTER 1 General Description ..................................................................1-1 1.1 Standard Features ....................................................................................1-2 1.2 Hardware Structure .................................................................................1-5 1.3 System Configuration..............................................................................1-7 CHAPTER 2 Specifications......................................
Summary of the content on the page No. 18
Contents 4.1.2 Mounting orientations .............................................................................4-3 4.1.3 Notes on mounting ..................................................................................4-3 4.2 Power Supply Requirements ...................................................................4-8 4.3 Connection Requirements .......................................................................4-9 4.3.1 Connector................................................
Summary of the content on the page No. 19
Contents 6.2.5 Tools and test equipment ........................................................................6-9 6.2.6 Tests ........................................................................................................6-9 6.3 Operation Check....................................................................................6-11 6.3.1 Initial seek operation check...................................................................6-11 6.3.2 Operation test .......................
Summary of the content on the page No. 20
Contents Illustrations Figures Figure 1.1 FC model drives outer view ......................................................... 1-5 Figure 1.2 Example of FC-AL system configuration.................................... 1-7 Figure 3.1 Cylinder configuration ................................................................. 3-2 Figure 3.2 Spare area in cell .......................................................................... 3-4 Figure 3.3 Alternate cylinder.............................
