Summary of the content on the page No. 1
C156-E224-01EN
MCJ3230SS
OPTICAL DISK DRIVE
PRODUCT MANUAL
Summary of the content on the page No. 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual. This prod
Summary of the content on the page No. 3
Revision History (1/1) Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 November, —— 2001 *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C156-E224-01EN
Summary of the content on the page No. 4
This page is intentionally left blank.
Summary of the content on the page No. 5
Preface This manual describes the MCJ3230SS 90 mm (3.5-inch) optical disk drive. This manual provides an overview of the above optical disk drives, and explains their specifications, the requirements and procedures for installing them in a system, and how to clean them. The manual is intended for users who have a basic understanding of optical disk drives and their use in computer systems. See "Manual Organization" for details of the organization of manuals related to optical disk drives and the
Summary of the content on the page No. 6
Preface Glossary The glossary describes the technical terms that need to be understood to read this manual. Acronyms and Abbreviations This manual contains a list of the abbreviations used in this manual and their meanings. CONVENTIONS USED IN THIS MANUAL Throughout this manual, the MCJ3230SS optical disk drive are described as an "ODD," "drive," "unit," "target (TARG)," or "device." Decimal values are indicated without any modifiers added. Hexadecimal values are indicated as X'17B9', 17B9h, 17B
Summary of the content on the page No. 7
Preface (Example) Low temperature burns: The surface temperatures of some ICs on the printed circuit board unit in the optical disk drive exceed 55°C while operating. Be careful of low tenperature burns. The main alert messages in the text are also listed in the “Important Alert Items.” Attention Please forward any comments you may have regarding this manual. To make this manual easier for users to understand, opinions from readers are needed. Please write your opinions or requests on the Commen
Summary of the content on the page No. 8
DISCLAIMER Failure of the MCJ3230SS optical disk drive is defined as a failure requiring adjustment, repair, or replacement. Fujitsu is not responsible for failure due to misuse, operation outside the specified environment conditions, power line trouble, controller problems, cable failure, or other failure not caused by the optical disk drive itself. iv C156-E224-01EN
Summary of the content on the page No. 9
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page 3-1 Low temperature burns: The surface temperatures of some ICs on the printed circuit board unit in the optical disk drive exceed 5
Summary of the content on the page No. 10
Important Alert Items Task Alert message Page Device damage: 3-22 Be sure to turn on the power supply before inserting your cartridge for the first time. It releases the device from transport protection and enables you to insert the cartridge. The device may be damaged if you insert the cartridge without releasing the protection. From the next time, you don't need to turn on the power supply beforehand. Before moving the drive, remove the optical disk cartridge. If the drive is moved with the op
Summary of the content on the page No. 11
MANUAL ORGANIZATION OPTICAL DISK DRIVE 1. GENERAL DESCRIPTION PRODUCT MANUAL 2. SPECIFICATIONS (C156-E224) 3. INSTALLATION REQUIREMENTS 4. HOST INTERFACE 5. OPERATION AND CLEANING 6. DIAGNOSTICS AND MAINTENANCE OPTICAL DISK DRIVES 1. MAINTENANCE AND DIAGNOSIS MAINTENANCE MANUAL 2. FAULT ANALYSIS (C156-F043) 3. REMOVAL AND REPLACEMENT PROCEDURES 4. PRINCIPLES OF OPERATION 5. CLEANING C156-E224-01EN vii
Summary of the content on the page No. 12
REFERENCED STANDARDS The product specifications and functions described in this manual conform to the following standards: Specification Name Concerned organization (document) number ANSI X3. 131-1986 American National Standard for Information American National Systems-Small Computer System Interface. Standards Institute (SCSI) (ANSI) American National Standard for Information ANSI X3. 131-1994 American National Systems-Small Computer System Interface-2. Standards Institute (SCSI-2) (ANSI) ISO/I
Summary of the content on the page No. 13
Contents Preface .........................................................................................................i DISCLAIMER .......................................................................................................iv MANUAL ORGANIZATION ...................................................................................vii CHAPTER 1 General Description.................................................................. 1-1 1.1 Features .......................................
Summary of the content on the page No. 14
Contents 2.3 Defect Management....................................................................................2-11 2.3.1 Defect management schematic diagram ..............................................2-11 CHAPTER 3 Installation Requirements.........................................................3-1 3.1 Environmental Requirements .......................................................................3-1 3.1.1 Temperature measurement point ..................................................
Summary of the content on the page No. 15
CHAPTER 4 Host Interface............................................................................ 4-1 4.1 Interface Connector ......................................................................................4-1 4.2 Various Processes.........................................................................................4-4 4.2.1 Reset response .......................................................................................4-4 4.2.2 Defective sector management .....................
Summary of the content on the page No. 16
Contents 4.3.21 FORMAT UNIT command .................................................................4-37 4.3.22 READ DEFECT DATA command .....................................................4-38 4.3.23 SEND DIAGNOSTIC command.........................................................4-39 4.3.24 RECEIVE DIAGNOSTIC RESULTS command................................4-39 4.3.25 WRITE BUFFER command................................................................4-40 4.3.26 READ LONG command .............
Summary of the content on the page No. 17
6.2 Maintenance Information .............................................................................6-3 6.2.1 Maintenance requirements ....................................................................6-3 6.2.2 Revision number ...................................................................................6-4 Glossary ……………………………………………………………………….GL-1 Abbreviations …….…………………………………………………………………AB-1 Index ………………………………………………………………………...IN-1 C156-E224-01EN xiii
Summary of the content on the page No. 18
Contents Illustrations Figures Figure 1.1 Outer view (with panel) .....................................................................................1-7 Figure 1.2 Outer view (without panel) ................................................................................1-7 Figure 1.3 Optical disk drive configuration ........................................................................1-8 Figure 1.4 Control circuit section block diagram.......................................................
Summary of the content on the page No. 19
Figure 6.1 Revision label ....................................................................................................6-4 Figure 6.2 Revision number indication...............................................................................6-4 C156-E224-01EN xv
Summary of the content on the page No. 20
Contents Tables Table 2.1 Model and order number....................................................................................2-1 Table 2.2 Specifications (1 of 2)........................................................................................2-2 Table 2.2 Specifications (2 of 2)........................................................................................2-3 Table 2.3 Environmental and power requirements (1 of 2) ...............................................2-4 Table 2
