Summary of the content on the page No. 1
C141-E198-02EN
MAS3735FC
MAS3367FC
DISK DRIVES
PRODUCT/MAINTENANCE MANUAL
Summary of the content on the page No. 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section "Important Alert Items" in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual.
Summary of the content on the page No. 3
Revision History (1/1) Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 2003.07.29 — — 02 2003.10.07 • Table 2.1, 2.2 and 3.2 are altered. Capacity notation is changed. Misdescription is corrected. • Table 2.3 is altered *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C141-E198
Summary of the content on the page No. 4
This page is intentionally left blank.
Summary of the content on the page No. 5
Preface This manual describes the MAS3735FC and MAS3367FC (hereafter, MAS series), 3.5 type fixed disk drives with an embedded fibre channel controller. This manual details the specifications and functions of the above disk drive, and gives the requirements and procedures for installing it into a host computer system. This manual is written for users who have a basic understanding of fixed disk drives and their use in computer systems. The MANUAL ORGANIZATION section describes organiz
Summary of the content on the page No. 6
Preface APPENDIX A Connector Signal Allocation The appendix gives supplementary information, including the signal assignments of interface connectors. Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazardou
Summary of the content on the page No. 7
Preface (Example) Data loss For MAS series, Reed Solomon codes are applied for their ECC. The sector-data is divided into 4 interleaving sectors, and ECC is performed in each sector where the maximum number of errors (up to 5 byte) can be corrected. [Total maximum byte: 5 byte × 4 ( interleave) = 20 byte] If the error of read sector keeps allowable error byte number, correction is performed. However, if error byte exceeds its allowable number, correction may not be performed prope
Summary of the content on the page No. 8
This page is intentionally left blank.
Summary of the content on the page No. 9
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Data loss Mounting Installation 2-5 For MAS series, Reed Solomon codes are applied for their ECC. The sector-
Summary of the content on the page No. 10
Important Alert Items Task Alert message Page Mounting Installation Damage 5-5 1. When dismounting the drive which is mounted on the system while power is supplied to it. • The drive to be dismounted must be separated from the loop. Dismounting the drive which is not separated from the loop may cause an unexpected error. • If the drive is not separated from the loop, issue an LPB to the drive from the initiator in a primitive sequence of the order set. • It is recommended to stop
Summary of the content on the page No. 11
Important Alert Items Task Alert message Page Mounting Installation Caution 6-6 1. Always ground yourself with a wrist strap connected to ground before handling. ESD (Electrostatics Discharge) may cause the damage to the device. 2. Do not remove a PCA. This operation is required to prevent unexpected or unpredictable operation. 3. Do not use a conductive cleaner to clean a disk drive assembly. Damage 6-6 Never open the disk enclosure in the field. Opening the disk enclosure in
Summary of the content on the page No. 12
This page is intentionally left blank.
Summary of the content on the page No. 13
MANUAL ORGANIZATION PRODUCT/ 1. General Description MAINTENANCE MANUAL 2. Specifications 3. Data Format (This manual) 4. Installation Requirements 5. Installation 6. Diagnostics and Maintenance 7. Error Analysis Fibre Channel 1. Command Processing Interface 2. Data Buffer Management Specifications 3. Command Specification 4. Sense Data and error Recovery Procedure 5. Disk Medium Management C141-E198 ix
Summary of the content on the page No. 14
REFERENCED STANDARDS The product specifications and functions described in this manual conform to the following ANSI (*1) standards: Document number Title NCITS TR-19 FIBRE CHANNEL PRIVATE LOOP SCSI DIRECT ATTATH (FC-PLDA) ANSI X3.230-1994 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE (FC-PH) ANSI X3.297-1996 FIBRE CHANNEL PHYSICAL AND SIGNALING INTERFACE-2 (FC-PH-2) ANSI X3.272-199X FIBRE CHANNEL ARBITRATED LOOP (FC-AL) ANSI X3.269-199X FIBRE CHANNEL PLOTOCOL FOR SCSI (SCSI-FCP)
Summary of the content on the page No. 15
CONTENTS CHAPTER 1 General Description ..................................................................1-1 1.1 Standard Features....................................................................................1-2 1.2 Hardware Structure.................................................................................1-5 1.3 System Configuration..............................................................................1-7 CHAPTER 2 Specifications........................................
Summary of the content on the page No. 16
Contents 4.1.1 External dimensions..............................................................................4-1 4.1.2 Mounting...............................................................................................4-3 4.1.3 Notes on mounting ................................................................................4-3 4.2 Power Supply Requirements ...................................................................4-7 4.3 Connection Requirements..............................
Summary of the content on the page No. 17
Contents 6.2.4 Revision numbers..................................................................................6-9 6.2.5 Tools and test equipment ....................................................................6-10 6.2.6 Tests....................................................................................................6-10 6.3 Operation Check....................................................................................6-12 6.3.1 Initial seek operation check ..............
Summary of the content on the page No. 18
Contents Illustrations Figures Figure 1.1 FC model drives outer view ........................................................1-5 Figure 1.2 Disk/head configuration..............................................................1-6 Figure 1.3 Example of FC-AL system configuration...................................1-7 Figure 3.1 Cylinder configuration ................................................................3-2 Figure 3.2 Spare area in cell .............................................
Summary of the content on the page No. 19
Contents Tables Table 2.1 Model names and order numbers................................................ 2-1 Table 2.2 Function specifications ............................................................... 2-2 Table 2.3 Environmental/power requirements............................................ 2-4 Table 3.1 Zone layout and track capacity ................................................... 3-3 Table 3.2 Format capacity......................................................................
Summary of the content on the page No. 20
This page is intentionally left blank.
