Summary of the content on the page No. 1
C141-E202-01EN
MHU2100AT
DISK DRIVE
PRODUCT MANUAL
Summary of the content on the page No. 2
FOR SAFE OPERATION Handling of This Manual This manual contains important information for using this product. Read thoroughly before using the product. Use this product only after thoroughly reading and understanding especially the section “Important Alert Items” in this manual. Keep this manual handy, and keep it carefully. FUJITSU makes every effort to prevent users and bystanders from being injured or from suffering damage to their property. Use the product according to this manual.
Summary of the content on the page No. 3
Revision History (1/1) Revised section (*1) Edition Date Details (Added/Deleted/Altered) 01 2004-01-20 *1 Section(s) with asterisk (*) refer to the previous edition when those were deleted. C141-E202-01EN
Summary of the content on the page No. 4
This page is intentionally left blank.
Summary of the content on the page No. 5
Preface This manual describes MHU2100AT model of the MHU Series, 2.5-inch hard disk drives. These drives have a built-in controller that is compatible with the ATA interface. This manual describes the specifications and functions of the drives and explains in detail how to incorporate the drives into user systems. This manual assumes that the reader has a basic knowledge of hard disk drives and their implementations in computer systems. This manual consists of seven chapters and sect
Summary of the content on the page No. 6
Preface Conventions for Alert Messages This manual uses the following conventions to show the alert messages. An alert message consists of an alert signal and alert statements. The alert signal consists of an alert symbol and a signal word or just a signal word. The following are the alert signals and their meanings: This indicates a hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. This alert signal also
Summary of the content on the page No. 7
Preface Attention Please forward any comments you may have regarding this manual. To make this manual easier for users to understand, opinions from readers are needed. Please write your opinions or requests on the Comment at the back of this manual and forward it to the address described in the sheet. Liability Exception “Disk drive defects” refers to defects that involve adjustment, repair, or replacement. Fujitsu is not liable for any other disk drive defects, such as those caused b
Summary of the content on the page No. 8
This page is intentionally left blank.
Summary of the content on the page No. 9
Important Alert Items Important Alert Messages The important alert messages in this manual are as follows: A hazardous situation could result in minor or moderate personal injury if the user does not perform the procedure correctly. Also, damage to the product or other property, may occur if the user does not perform the procedure correctly. Task Alert message Page Normal Operation 3-7 Data corruption: Avoid mounting the disk near strong magnetic sources such as loud speakers
Summary of the content on the page No. 10
This page is intentionally left blank.
Summary of the content on the page No. 11
Manual Organization MHU2100AT • Device Overview Device Configuration DISK DRIVE Installation Conditions PRODUCT MANUAL Theory of Device Operation (C141-E202) Interface Operations MHU2100AT Maintenance and Diagnosis Removal and Replacement Procedure DISK DRIVE MAINTENANCE MANUAL (C141-F067) C141-E202-01EN vii
Summary of the content on the page No. 12
This page is intentionally left blank.
Summary of the content on the page No. 13
Contents CHAPTER 1 Device Overview........................................................................1-1 1.1 Features ..............................................................................................................1-2 1.1.1 Functions and performance .....................................................................1-2 1.1.2 Adaptability.............................................................................................1-2 1.1.3 Interface...................
Summary of the content on the page No. 14
Contents CHAPTER 3 Installation Conditions ............................................................. 3-1 3.1 Dimensions ........................................................................................................ 3-2 3.2 Mounting............................................................................................................ 3-3 3.3 Cable Connections............................................................................................. 3-9 3.3.1 Device
Summary of the content on the page No. 15
Contents 4.6.2 Write circuit.............................................................................................4-9 4.6.3 Read circuit............................................................................................4-10 4.6.4 Digital PLL circuit.................................................................................4-11 4.7 Servo Control ...................................................................................................4-12 4.7.1 Servo cont
Summary of the content on the page No. 16
Contents (13) IDLE IMMEDIATE (X’95’ or X’E1’) .........................................5-36 (14) STANDBY (X’96’ or X’E2’) .......................................................5-37 (15) IDLE (X’97’ or X’E3’) .................................................................5-38 (16) CHECK POWER MODE (X’98’ or X’E5’).................................5-40 (17) SLEEP (X’99’ or X’E6’) ..............................................................5-41 (18) SMART (X’B0) ...................
Summary of the content on the page No. 17
Contents (46) SET MAX ADDRESS EXT (X’37’): Option (customizing)...............................................................................5-117 (47) WRITE MULTIPLE EXT (X’39’): Option (customizing)........5-119 (48) WRITE LOG EXT (X’3F’) [Optional command (Customize)]................................................................................5-120 (49) READ VERIFY SECTOR (S) EXT (X’42): Option (customizing)...................................................................
Summary of the content on the page No. 18
Contents 5.6.3.1 Initiating an Ultra DMA data in burst ..................................... 5-148 5.6.3.2 Ultra DMA data burst timing requirements ............................ 5-149 5.6.3.3 Sustained Ultra DMA data in burst......................................... 5-152 5.6.3.4 Host pausing an Ultra DMA data in burst............................... 5-153 5.6.3.5 Device terminating an Ultra DMA data in burst..................... 5-154 5.6.3.6 Host terminating an Ultra DMA data in bur
Summary of the content on the page No. 19
Contents 6.4.3.1 Miss-hit ......................................................................................6-15 6.4.3.2 Sequential Hit.............................................................................6-16 6.4.3.3 Full hit ........................................................................................6-17 6.4.3.4 Partial hit....................................................................................6-18 6.5 Write Cache...................................
Summary of the content on the page No. 20
Contents Illustrations Figures Figure 1.1 Negative voltage at +5 V when power is turned off ......................... 1-6 Figure 1.2 Current fluctuation (Typ.) at +5 V when power is turned on............................................................................................ 1-8 Figure 2.1 Disk drive outer view ........................................................................ 2-2 Figure 2.2 1 drive system configuration.....................................................
