Summary of the content on the page No. 7
3.2 Mounting (5) Service area Figure 3.5 shows how the drive must be accessed (service areas) during and after installation. Mounting screw hole Cable connection Mounting screw hole Figure 3.5 Service area Data corruption: Avoid mounting the disk drive near strong magnetic sources such as loud speakers. Ensure that the disk drive is not affected by external magnetic fields. Damage: Do not press the cover of the disk drive. Pressing it too hard, the cover and the spindl
Summary of the content on the page No. 8
Installation Conditions - General notes ESD mat Wrist strap Shock absorbing mat Use the Wrist strap. Place the shock absorbing mat on the operation table, and place ESD mat on it. Do not hit HDD each other. Do not stack when carrying. Do not place HDD vertically Do not drop. to avoid falling down. Figure 3.6 Handling cautions - Installation (1) Please use the driver of a low impact when you use an electric driver. HDD is occasionally damaged by the impact of the
Summary of the content on the page No. 9
3.3 Connections with Host System 3.3 Connections with Host System 3.3.1 Device connector The disk drive has the SATA interface connectors listed below for connecting external devices. Figure 3.7 shows the locations of these connectors and terminals. SATA interface and power connectors PCA Figure 3.7 Connector locations C141-E280 3-9
Summary of the content on the page No. 10
Installation Conditions 3.3.2 Signal segment and power supply segment Figure 3.8 shows each segment of the SATA interface connector and pin numbers. View from the connector side Power supply Signal segment segment View from the PCA side S1 pins in the signal P1 pins in the power segment supply segment Figure 3.8 Power supply pins (CN1) 3.3.3 Connector specifications for host system The connector of host system for mating with the disk drive must be compliant with Se
Summary of the content on the page No. 11
3.3 Connections with Host System 3.3.4 SATA interface cable connection The cable that connects the disk drive to the host system must be compliant with the Serial ATA Revision 2.6 specification. 3.3.5 Note about SATA interface cable connection Take note of the following precaution about plugging a SATA interface cable into the SATA interface connector of the disk drive and plugging the connector into a host receptacle: When plugging together the disk drive SATA interface connecto
Summary of the content on the page No. 12
This page is intentionally left blank.
Summary of the content on the page No. 1
CHAPTER 3 Installation Conditions
3.1 Dimensions
3.2 Mounting
3.3 Connections with Host System
This chapter gives the external dimensions, installation conditions, surface
temperature conditions, cable connections, and switch settings of the hard disk
drives.
C141-E280 3-1
Summary of the content on the page No. 2
Installation Conditions 3.1 Dimensions Figure 3.1 illustrates the dimensions of the disk drive. All dimensions are in mm. *1 The PCA and connectors are not included in these dimensions. *2 Dimension from the center of the user tap to the base of the connector pins *3 Length of the connector pins *4 Dimension from the outer edge of the user tap to the center of the connector pins *5 Dimension from the outer edge of the user tap to the innermost edge of the connector pins Figure 3
Summary of the content on the page No. 3
3.2 Mounting 3.2 Mounting For information on mounting, see the "FUJITSU 2.5-INCH HDD INTEGRATION GUIDANCE (C141-E144)." (1) Orientation The disk drives can be mounted in any direction. (2) Frame The MR head bias of the HDD disk enclosure (DE) is zero. The mounting frame is connected to Signal Ground (SG). Use M3 screw for the mounting screw and the screw length should satisfy the specification in Figure 3.2. The tightening torque must be 0.49N•m (5kgf•cm). When attaching the H
Summary of the content on the page No. 4
Installation Conditions (3) Limitation of mounting Note) These dimensions are recommended values; if it is not possible to satisfy them, contact us. Side surface 2.5 2.5 mounting Bottom surface mounting 2.5 DE 2.5 2 B PCA A Frame of system Frame of system cabinet cabinet 3.0 or less Screw Screw 3.0 or less Details of A Figure 3.2 Mounting frame structure 3-4 C141-E280
Summary of the content on the page No. 5
3.2 Mounting Because of breather hole mounted to the HDD, do not allow this to close during mounting. Locating of breather hole is shown as Figure 3.3. For breather hole of Figure 3.3, at least, do not allow its around φ 3 to block. Figure 3.3 Location of breather C141-E280 3-5
Summary of the content on the page No. 6
Installation Conditions (4) Ambient temperature The temperature conditions for a disk drive mounted in a cabinet refer to the ambient temperature at a point 3 cm from the disk drive. The ambient temperature must satisfy the temperature conditions described in Section 1.4, and the airflow must be considered to prevent the DE surface cover temperature from exceeding 60 °C. Provide air circulation in the cabinet such that the PCA side, in particular, receives sufficient cooling. To che
