Summary of the content on the page No. 1
UV-AIRE™ AIR PURIFYING SYSTEM
Model: UV-12C,18C,28C,28,12HP,18HP,28HP,12HPC,18HPC,28HPC
*Exclusive 5 position lamp mounting feature!
ITEMS INCLUDED IN KIT:
1-UV-Aire ™ power unit
4-Sheet metal mounting screws
1-Angled mounting bracket
1-Flat mounting bracket
1-Duct board mounting bracket
1-Ultra Violet lamp
1-Instruction Sheet
1-Wing nut
Caution Labels
Gasket
UV-C light inhibits the growth and reproduction of germs and bacteria that circulate through a
homes’ heating and air con
Summary of the content on the page No. 2
I. INDICATION FOR USE This product is not sold as a medical device and is not for the purpose of diagnosis of any disease or condition nor for use in the mitigation, treatment, or prevention of any disease or condition. II. GENERAL INFORMATION There are different size units available, depending on the square footage of your home. See chart below for determining your homes needs. Minimum Max Air Lamp Intensity at 1 Recommended Model Duct Volts Amps Watts Hz Temp °F meter Max Sq. Feet
Summary of the content on the page No. 3
III. INSTALLATION 1. Locate a suitable location for the unit downstream from the ‘A’ coil in the supply plenum or in the return plenum; preferably downstream from the air filter. For optimum “cleaning” effect on the ‘A’ coil, mount the unit in the supply plenum as close as possible to the ‘A’ coil. (See Figure 1) Figure 1 WARNING: Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage or blindness. Never operate the UV-Aire™
Summary of the content on the page No. 4
2. Determine the type of duct you have. (For flex duct applications, refer to Figure 26 on page 11) IF YOU HAVE METAL DUCT: a. Apply supplied wet and stick mounting template to air duct in either a vertical or horizontal position as shown in Figure 2. b. Drill 1/8” diameter mounting holes at positions indicated on template. c. Cut out the marked openings on the template. (Refer to template as shown in Figure 2) d. Remove the paper template from the duct. IF YOU HAVE DUCT BOARD: Figu
Summary of the content on the page No. 5
3. Remove base unit and cover from box. 4. Apply supplied “Duct Seal Kit” according to instructions included in kit. (See Figure 12) Figure 12 5. Determine whether to use flat or angled bracket. (Refer to “Bulb Mounting Bracket Selection” in Section VI for aid in this decision) a. Flat Bracket Installation i. Remove the two hex nuts and flat bracket from included bagged hardware. ii. Install the flat bracket and secure to the unit base with the hex nuts provided. (See Figure 13) Figur
Summary of the content on the page No. 6
8. Insert lamp through the hole until lamp cannot be inserted any further. (See Figure 16) Figure 16 9. Swing the swivel bracket over the end of lamp. Hand-tighten the wing nut on the stud. Be careful no to over tighten the wing nut. The porcelain at the lamp base may crack when over tightened. (See Figure 17) Figure 17 10. Plug ballast plug into end of lamp. (See Figure 18) Figure 18 11. Snap cover onto the unit base. (See Figure 19) Figure 19 12. Plug the LED wire from the cover
Summary of the content on the page No. 7
13. Close the cover and tighten cover screw. (See Figure 21) 14. Plug the power cord into a standard electrical outlet. NOTE: Seal the joints and seams of the plenum near the mounting location to reduce any direct viewing of light. (See Figure 1) 15. Press the power switch to the “ON” position. (Light on switch should be on indicating power.) 16. Look through view port in the box cover to be sure the lamp is working. You should see a blue glow. (The view port is covered with a plastic l
Summary of the content on the page No. 8
V. ALARM CIRCUIT WIRING The UV Aire units supplied with a circuit board allows for the wiring of the UV Aire unit into an alarm or security system to monitor the operation of the UV lamp. This circuit is a set of normal open contacts that close if the operational time exceeds 9000 hrs or if the lamp burns out. 1. Turn off power switch on the UV Aire unit and unplug the unit before doing any wiring. 2. Loosen the cover screw and open the unit cover. 3. Locate terminals 1-2 on the circuit
Summary of the content on the page No. 9
VI. BULB MOUNTING BRACKET SELECTION TM The UV-AIRE units come with an angled mounting bracket and flat mounting bracket to position the bulb either straight or at an angle. Choose one or the other bracket method best suited for your needs. Refer to the configurations chart below when making your selection. UV-Aire™ Configurations Good Best Exclusive 5 Position Mounting Straight Angled Positions Standard 90° Patent Pending Installation Angled Installation (Flat Bracket) Single La
Summary of the content on the page No. 10
VII. MAINTENANCE 1. Inspect and clean lamp at least every 6 months. 2. Replace your UV-Aire™ Air Purifying System lamp once a year to maintain the lamps maximum output intensity. The lamp should operate continuously for maximum lamp life and light effectiveness. VIII. REPLACEMENT PROCEDURE VERY IMPORTANT: Turn switch on unit to “OFF” position and unplug unit from outlet. 1. Loosen the cover screw on the side of the unit and open cover. 2. Unplug ballast plug from end of lamp. 3. Loosen t
Summary of the content on the page No. 11
IX. TROUBLESHOOTING GUIDE 1. If the LED is illuminating a “YELLOW” color and the circuit board alarm beeps every 15 minutes, the lamp should be replaced soon. 2. If the LED is illuminating a “RED” color and the circuit board alarm beeps every 5 minutes, the lamp should be replaced immediately. 3. If the lamp does not light up, replace lamp. 4. If the lamp still does not light up after replacing the lamp, replace ballast. X. REPLACEMENT PARTS LIST LAMP CIRCUIT BOARD BALLAST MODEL (Fiel
Summary of the content on the page No. 12
WARRANTY INFORMATION Limited Warranty Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under normal use for eighteen (18) months from date of manufacturing by the consumer excepting the provisions numbered below. UV-LAMPS/BULBS Field Controls, L.L.C. warrants that the following Field Controls, L.L.C. products sold hereunder, shall be free from defects in material and workmanship under n
