Summary of the content on the page No. 1
Rosemount Analytical
NGA 2000
Software Manual
MLT Analyzer
MLT Analyzer Module
(combined with NGA 2000 platform /
MLT analyzer / TFID analyzer
or customer-developed control unit)
Software Version 3.2.X
nd
2 Edition 07/98
Catalog No.: 90 003 482
Managing The Process Better
90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98
Summary of the content on the page No. 2
Rosemount Analytical This Operation Manual includes information about the operation of the instrument. Information about the additional indications and notes regarding maintenance, troubleshooting and repair are found in the accompanying Maintenance & Operation Manual. Troubleshooting, component replacement and internal adjustments must be made by qualified service personnel only. Fisher-Rosemount GmbH & Co does not take responsibility for any omissions or errors in this manual. Any liability fo
Summary of the content on the page No. 3
Contents 1 Introduction 1 - 1 2 Structure of Menus 2 - 1 3 Startup and Operation, General Notes and Main Menu 3 - 1 3.1 Starting and Initializing ................................ ................................ ................... 3 - 1 3.2 Display and Function ................................ ................................ ...................... 3 - 2 3.3 "TAG" and Operating Keys ................................ ................................ ............ 3 - 2 3.4 Lines and Softkey Functi
Summary of the content on the page No. 4
5 Analyzer and I/O-Module Expert Configuration 5 - 1 5.1 Analyzer Module Setup 5 - 3 5.1.1 Calibration Parameters ................................ ................................ ................... 5 - 5 – Span gases ................................ ................................ ......................... 5 - 6 – Tolerances ................................ ................................ .......................... 5 - 7 – Calibration procedure setup ................................ ........
Summary of the content on the page No. 5
5.2 I/O Module Controls 5 - 83 5.2.1 SIO Module 5 - 84 5.2.2 DIO Module(s) 5 - 93 5.3 I/O Module Setup 5 - 99 6 System Configuration 6 - 1 6.1 Diagnostic Menus ................................ ................................ ........................... 6 - 3 6.1.1 Control Module Diagnostics ................................ ................................ . 6 - 4 6.1.2 Analyzer Module Diagnostics ................................ .............................. 6 - 5 6.2 Date and Time ...........
Summary of the content on the page No. 6
IV 90003482(2) [ NGA-e ( MLT-Software 3.2.X)] 07/98 NGA 2000
Summary of the content on the page No. 7
1 Introduction This software manual describes step by step how to operate successfully with the ½ 19" and 19" MLT analyzer module and analyzer of the NGA 2000 Series. Chapter two shows the structure of the MLT software menus. Chapter three describes the display and the keyboard of the analyzer. Chapter four describes the basic controls with detailed illustrations. So you can easily compare the actual display of the analyzer module with the illustrations of the manual. Chapter five describes the
Summary of the content on the page No. 8
The following illustrations shall make plain the connection between the hardware configu- ration and the software setup of the modules: NGA 2000 System via Platform Local Analyzer Control I/O I/O's Modules (AM's) Module (CM) Modules SIO (see 5.1.18) (see 5.2.1) SIO (see 5.1.18) MLT (see 5.2.2) (additional CLD manuals) (additional PMD manuals) (additional manuals) NGA 2000 System via MLT Analyzer Local Analyzer Control System I/O I/O's Modules (AM's) Module (CM) Modules SIO (see 5.1.18) MLT (see
Summary of the content on the page No. 9
1 Introduction NGA 2000 System via TFID Analyzer Local Analyzer Control System I/O I/O's Modules (AM's) Module (CM) Modules SIO (see 5.2.1) (see 5.1.18) SIO (see 5.1.18) MLT (see 5.2.2) (additional CLD manuals) (additional PMD manuals) (additional manuals) 90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98 1 - 3 TFID Analyzer NGA 2000 FID DIO 1 DIO DIO 1 SIO TFID
Summary of the content on the page No. 10
1 - 4 90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98 NGA 2000
Summary of the content on the page No. 11
2 Structure of Menus Section 7 Display controls of the front panel LCD Front panel control (number of digits) Auxiliary lines (for the single component display) - - - Section 3.8 Section 6 System calibration... Diagnostic menus... Date and time... Security codes... (Lock of each level) Network module binding... System reset... System modules... System tag - - - - - - - - odule (AM). m utput Module). nalyzer O a nput-/ I Section 5 odule), I/O ( M Analyzer module controls... I/O module controls.
Summary of the content on the page No. 12
2 - 2 90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98 NGA 2000
Summary of the content on the page No. 13
3 Startup and Operation, General Notes and Main Menu 3.1 Starting and Initializing After switching on the MLT analyzer or analyzer module (in a platform or part of a NGA network), the initialization procedure will be performed. A self control of the analyzer modules or the analyzer is running. You can see a sequence of several displays. They show the status of initialization, revision notes of the MLT software and the tag: (C) 1998 FISHER-ROSEMOUNT Analytical NGA-2000 Control Module/Version
Summary of the content on the page No. 14
3.2 Display and Function The LCD screen shows all measurement values of the analyzer and all customer instructions. You can operate with five function keys, four arrow keys (cursors) and the enter key. The function of each key depends on: ♦ the type of analyzer/analyzer module used ♦ the optional auxiliary modules (e.g. I/O boards) used ♦ the individual menu displayed In case of power failure all customer specific module parameters are saved by a battery- powered buffer. 3.3 "TAG" and Operating
Summary of the content on the page No. 15
3 Startup and Operation, General Notes and Main Menu 3.4 Lines and Softkey Functionality Lines can be selected by the ↓ ↓ -key or the ↑ ↑ -key. The selected line is displayed white on black. You have four different types of lines in the menu: Menu line... / Menu Softkey... ♦ Line/Softkey lettering ending with three dots. ♦ You will go to a submenu/further menu by pressing the softkey resp. by pressing the 88 -key or the → → -key in the menu line. Function line / Function Softkey ! ♦ Line/Softk
Summary of the content on the page No. 16
Text Line -- Calibration Procedure Status -- Procedure status: Ready Remaining procedure time: Current/expected gas flow: Samplegas Concentration in span gas units: 37.50 ppm Last zero calibration: Success Last span calibration: Success Last zero calibration was: Fri 05-29-1998 13:32:06 Last span calibration was: Fri 05-29-1998 13:37:23 Successful zero+span calibrated ranges: 1+2+3+4 Cancel ! Back... F1 F2 F3 F4 F5 Menu Softkeys Function Softkey 3.5 Important Functions of the Softkeys Display ♦
Summary of the content on the page No. 17
3 Startup and Operation, General Notes and Main Menu Lock ♦ Lock of all three operation levels from the main menu, if a security code is activated in the system configuration level (see section 6.3 p. 6-7). ♦ F4 in the main menu. Calib (see section 4.4 p. 4-37 and 5.1.1 p. 5-15!) ♦ Change from the single component display to the menu "Analyzer module calibration". ♦ F5 in the single component display. MFG Data (see section 3.8 p. 3-7/8!) ♦ Change from the main menu to the menu "Module Manufactu
Summary of the content on the page No. 18
3.7 Starting a function If you press the 88 -key or the → → -key in a function line, you will be asked to confirm the order in the following way: -- Confirmation Required -- Press "Yes" or "Back..." Back... F1 F2 F3 F4 F5 ♦ If you will press the F2 key, the function will start immediately. ♦ If you will press the F4 key, you will go back to the last menu page. Note: If you don't want to be asked before the start of each function, you can configure it in the menu "Measurement Display Configurati
Summary of the content on the page No. 19
3 Startup and Operation, General Notes and Main Menu 3.8 Main Menu If you press the F3 key (Main...) or the → → -key in any single component display, you will change to the "Main Menu". From there you can change to all operating levels of your MLT analyzer or analyzer module to set up and control the parameters of measurement, calibration and data transfer ! Via the F5 key (MFG Data) you can change to several submenus, where you will find a lot of important data about the control module (MLT an
Summary of the content on the page No. 20
Ramifications from the menu "Module Manufacturing Data": 1. Control module data: 95.00 ppm 95.00 ppm Industriestrasse 1 <<< >>> F1 F2 F3 F4 F5 F1 F2 F3 F4 F5 95.00 ppm 95.00 ppm 3.2.1/P001 F1 F2 F3 F4 F5 F1 F2 F3 F4 F5 2. Analyzer module data: 95.00 ppm 95.00 ppm Industriestrasse 1 <<< >>> F1 F2 F3 F4 F5 F1 F2 F3 F4 F5 95.00 ppm 95.00 ppm 3.2.1 / P001 2 F1 F2 F3 F4 F5 F1 F2 F3 F4 F5 3 - 8 90003482(2) [ NGA-e ( MLT-Software 3.2.X)] 07/98 NGA 2000 Back... Channel Measure More... Back... Measure Se
