Summary of the content on the page No. 1
Agilent B2200A
Femto Leakage Switch
Mainframe
Agilent B2201A
14ch Low Leakage Switch
Mainframe
User’s Guide
Agilent Technologies
Summary of the content on the page No. 2
Notices © Agilent Technologies 2004, 2005 defined in FAR 52.227-19(c)(1-2) (June Warranty 1987). U.S. Government users will receive No part of this manual may be reproduced in The material contained in this docu- no greater than Limited Rights as defined in any form or by any means (including elec- ment is provided “as is,” and is sub- FAR 52.227-14 (June 1987) or DFAR tronic storage and retrieval or translation ject to being changed, without notice, 252.227-7015 (b)(2) (November 1995), a
Summary of the content on the page No. 3
DECLARATION OF CONFORMITY According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014 Manufacturer’s Name : Agilen t Technologies International sarl Manufacturer’s Address: Rue de la Gare 29 Supplier’s Address : CH - 1110 Morge s Switzerland Declares under sole responsibility that the product as originally delivere d Product Name : Femto Leakag e Switch Mainframe Femto Leakage Switch Modul e 14ch Low Leakag e Switch Mainfram e 14ch Low Leakag e Switc h Modul e Model Number : Agilen t B2200A Agilent B
Summary of the content on the page No. 4
• Herstellerbescheinigung GEÄUSCHEMISSION Lpa < 70 dB am Arbeitsplatz normaler Betrieb nach DIN 45635 T. 19 • Manufacturer’s Declaration ACOUSTIC NOISE EMISSION Lpa < 70 dB operator position normal operation per ISO 7779 NOTE This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme ?Hla norme NMB-001 du Canada. This product complies with the WEEE Directive (2002/96/EC) marking requirements. The affixed label indicates that you must not discard this electrical/ electronic
Summary of the content on the page No. 5
Safety Summary The following general safety precautions must be observed during all phases of operation, service, and repair of this instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual may impair the protections provided by the equipment. In addition, it violates safety standards of design, manufacture, and intended use of the instrument. Agilent Technologies, Inc. assumes no liability for customer’s failure to comply with these requiremen
Summary of the content on the page No. 6
• DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification to the instrument. Return the instrument to a Agilent Technologies Sales and Service Office for services and repair to ensure that safety features are maintained. • DANGEROUS PROCEDURE WARNINGS Warnings, such as example below, precede potentially dangerous procedures throughout this manual. Instructions contained in t
Summary of the content on the page No. 7
Safety Symbols The general definitions of safety symbols used on equipment or in manuals are listed below. Instruction manual symbol: the product will be marked with this symbol when it is necessary for the user to refer to the instruction manual in order to protect against damage to the instrument. Indicates dangerous voltage and potential for electrical shock. Do not touch terminals that have this symbol when insrument is on. Affixed to product containing static sensitive devices--use anti
Summary of the content on the page No. 8
In This Manual This manual is a user’s guide for Agilent B2200A/B2201A Switch Mainframe, and consists of the following chapters: • Introduction Describes an overview and specifications of the Agilent B2200 series. • Installation Describes how to install the Agilent B2200 and how to setup the input/output. • Front Panel Operation Explains the front panel operation and the switch control functions of the Agilent B2200, also provides the reference information of the front panel keys and display
Summary of the content on the page No. 9
Contents 1. Introduction Agilent B2200 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 10
Contents Self-Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Output Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Connector Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 To Make Connecti
Summary of the content on the page No. 11
Contents To Set GPIB Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 To Set Remote Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 To Return to Local Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11 Switch Control Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12 Channel Configuration Mode. . . . . . . . . .
Summary of the content on the page No. 12
Contents Using Couple Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Saving Input/Output Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Defining Comment for Internal Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 Capacitance Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Capacitance Compensation Function. . . . . . . . . . . .
Summary of the content on the page No. 13
Contents [:ROUTe]:AGND:CHANnel:DISable[:LIST] . . . . . . . . . . . . . . . . . . . . . . . . 5-25 [:ROUTe]:AGND:CHANnel:ENABle:CARD. . . . . . . . . . . . . . . . . . . . . . . . . 5-25 [:ROUTe]:AGND:CHANnel:ENABle[:LIST] . . . . . . . . . . . . . . . . . . . . . . . . 5-26 [:ROUTe]:AGND:PORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-27 [:ROUTe]:AGND[:STATe]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28 [:ROUTe]:A
Summary of the content on the page No. 14
Contents :SYSTem:ERRor? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49 :SYSTem:KLC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-49 :SYSTem:MEMOry:COMMent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-50 :SYSTem:MEMOry:DELete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-50 :SYSTem:MEMOry:LOAD . . . . . . . . . . . . . . . . . . . . . .
Summary of the content on the page No. 15
Contents agb220xa_cmdData_Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 agb220xa_cmdInt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 agb220xa_cmdInt16Arr_Q. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 agb220xa_cmdInt16_Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 agb220xa_cmdInt32Arr_Q. . . . . . . . . . . . . .
Summary of the content on the page No. 16
Contents agb220xa_readStatusByte_Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29 agb220xa_reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30 agb220xa_revision_query . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30 agb220xa_selectCompenFile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-30 agb220xa_self_test. . . . . . . . . . . . . . . . .
Summary of the content on the page No. 17
1 Introduction
Summary of the content on the page No. 18
Introduction This chapter describes the basic functions and features of the Agilent B2200A/B2201A (Agilent B2200 series), and consists of the following sections: • “Agilent B2200 Series” • “Front Panel” • “Rear Panel” • “Switch Modules” • “Specifications” • “Accessories and Options” 1-2 Agilent B2200 User’s Guide, Edition 2
Summary of the content on the page No. 19
Introduction Agilent B2200 Series Agilent B2200 Series Agilent B2200 series is a switching matrix designed for semiconductor dc characteristics measurement applications. The Agilent B2200 series has 14 input ports and four card slots for the switch modules (plug-in cards), and can configure a 12, 24, 36, or 48 outputs switching matrix. The Agilent B2200A/B2201A supports the following dedicated switch module. • Agilent B2210A fA Leakage Switch Module Dedicated for the Agilent B2200A mainframe
Summary of the content on the page No. 20
Introduction Front Panel Front Panel The Agilent B2200 series provides the front panel keys, the LCD, and the LED matrix display for the status monitor and connection setup. • Line switch Used to turn the Agilent B2200 on or off. •LCD Used to monitor the status and set the connection. See Chapter 3 for the details. • Front panel keys Used to set the Agilent B2200. See Chapter 3 for the details. • LED matrix display Displays the status of the matrix switches. Also used to set the matrix connecti
