Summary of the content on the page No. 1
Shuttle Brewer & Airpot/Shuttle Brewers
Operation and Instruction Manual
For Models P300E, P400E, RAP300E,
RAP400E, RAPS300E, RAPS400E
Table of Contents
Installation:
Installation and Start-up ....................................... 1-2
Operation .......................................................... 3
WARNING
Adjustments ........................................................ 4-7
Care and Cleaning ............................................... 8-9
Service .................................
Summary of the content on the page No. 2
Installation (con't) Electric Hook-up 1) The electric ratings for your brewer are printed on its nameplate. Typical electric ratings are: P300, P400, RAP300, RAP400 Optional 120/208V, 3.8kW, 18A or 120/240V 5.0kW, 21A, 1 phase Standard 120/208V, 5.0kW, 24A or 120/240V 6.6kW, 28A, 1 phase RAPS300, RAPS400 Standard 120/208V, 4.4KW 21A or 120/240V, 5.6KW 24A, 1 phase If the brewer includes the three heater tank option C21A, the ratings will be different. Always see the nameplate for correct ratin
Summary of the content on the page No. 3
Operation CAUTION HOT LIQUID HAZARD! Water used for brewing coffee is very hot. Use caution when brewing, pouring, or transporting coffee. Accidental spills may result in severe burns. 1) RAPS Brewers require the accessory warmer base placed over the pegs on the brew shelf before brewing into a shuttle. Plug the base into the receptacle on the side of the brewer. The receptacle is only energized when a shuttle is in place. 2) Place an empty, warm shuttle or airpot on the shelf, counter, or acce
Summary of the content on the page No. 4
Adjustments WARNING Electrical Shock Hazard! Dangerous electric voltages are present near adjustable components. All adjustments should be performed by qualified service personnel only. All adjustable components are located under the top cover. To access these parts: 1) Shut off the electric line to the brewer or unplug the brewer. 2) Remove the single screw fastening the top cover. Remove the top cover. 3) Pull forward and lift off the top cover. Brew Volume, Brew Timer The brew volume of the b
Summary of the content on the page No. 5
Two Batch Timer with Knob Adjustment, See Figure 2: This timer is adjustable from 15 seconds to 5 minutes. Locate the adjustment knobs under the top cover. Set this timer by adjusting the knob. The batch selector switch picks the adjustment potentiometer which the timer will see. Figure 2 Two Batch Timer Two Batch Timer with Counter Adjustment, See Figure 3: The two batch size timer may also be used with optional counter potentiometer to ease adjustments. Each batch size is adjustable from 00
Summary of the content on the page No. 6
To Adjust the Bypass: 1) Shut off and open brewer as described at the beginning of the adjustments section. 2) Locate the bypass valve for the brew head you wish to adjust. Valve is on the right and front of the BREW valve. 3) Open the valve (counter clockwise) to the desired setting. Use the table below as a guide: BYPASS SETTING BYPASS: % OF TOTAL BREW closed 0 1 turn 8 2 turns 12 3 turns 22 4 turns 33 4) Measure the bypass setting: a) Remove the brew basket. b) Place an empty shuttle without
Summary of the content on the page No. 7
4) If the maximum temperature adjustment needs to be increased, insert a small flat screwdriver into the shaft. Turn the calibration screw counter clockwise to increase the maximum temperature. Optional Solid State Thermostat: This control maintains temperature within 3°F. The adjustable range is from 155°F to 205°F. See Figure 6. 1) Shut off power and open top cover. 2) Locate thermostat on bracket mounted to front panel. 3) Adjust the knob to the temperature desired. This control cannot be set
Summary of the content on the page No. 8
Cleaning WARNING Burn Hazard! Hot liquids and surfaces are present in this equipment. To avoid burns use caution when cleaning. Rinse hot parts with cold water before cleaning. Use gloves or a heavy cloth when removing hot parts from brewer. After Each Brew: 1) Dispose of grounds and rinse brew basket. 2) Rinse shuttle or airpot containers before reuse. Every Day: 1) Wash brew basket with warm soapy water. The wire basket is removable to aid cleaning. 2) Remove spray head(s), located above brew
Summary of the content on the page No. 9
Weekly or Bi-Weekly, Depending on Use 1) Fill shuttles with one gallon, 2/3 full, of hot water. 2) Pour into the shuttle liners the recommended concentration of urn cleaner (excessive amounts of cleaner will attack the stainless steel). Urn cleaners that have been used successfully: DIP-IT, manufactured by Economics Laboratories, Inc. 4 Corporate Park Drive White Plains, NY 10604 OXYLITE, manufactured by Avril, Inc., Syndet Division 601 N. Third Street Reading, PA 19601 3) Scrub the liner inter
Summary of the content on the page No. 10
Service (con't) Drain Water Tank Always empty the tank before shipping. WARNING Draining of tank should be performed by a qualified service technician. The tank contains very hot water. May cause severe burns. Note: Brewer may contain over 5 gallons of hot water. 1) Prepare a heat resistant container to drain tank water into. 2) Shut off power to the brewer. 3) Remove the front access panel. 4) Pinch or clamp the silicone hose connected to fill valve. 5) Disconnect hose from outlet barb on fill
Summary of the content on the page No. 11
Troubleshooting: Filling, Heating, and Brewing Filling Problems The filling system consists of the following components: • Liquid Level Control, located behind the brewer front panel. • Liquid Level Probes, located on the tank top, secured by wing nut, under the top cover. • Fill Valve, located behind the front panel. Problem Possible Cause Service Check Remedy Overfilling water Fill valve not sealing Water entering tank Disassemble valve and clean out properly. continuously, usually dirt. Va
Summary of the content on the page No. 12
Troubleshooting: Filling, Heating, and Brewing Heating Problems The heating system consists of the following components: • Liquid Level Control, located behind the front enclosure panel. • Liquid Level Probes, located on the tank top, secured by wing nut, under the top cover. • Thermostat, located on the tank or on the front of top control panel under top cover. • Heater Relay, located in top control section under top cover. • Heating Elements, located on tank top under top cover. Problem P
Summary of the content on the page No. 13
Troubleshooting: Filling, Heating, and Brewing Brewing Problems The brewing system consists of the following components: • Start and Stop, switches located in the top control panel. • Brew Timer, located in the top control section under the top cover. • Brew Valve, located in the top control section under the top cover. Problem Possible Cause Service Check Remedy Adjust timer. Compare timer setting to Brew volume too Timer out of factory setting chart. adjustment. large or too small. Fill va
Summary of the content on the page No. 14
Parts Illustration for Models P300E & P400E Item Part # Description Item Part # Description BRASS SPRAY TEE W/ BYPASS TUBING 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 13 A725-081 1 A545-015 LEG, 4” SS (OPTIONAL) 14 A530-009 BREW TIMER 0-8 MINUTES 2 A537-043 HOT WATER FAUCET W/ NUT 15 A585-021 SPRAY TUBING 3/8” ID X 5/8”OD X 6”LG 3 A531-035 TERMINAL BLOCK 16 A712-018 ELECTRODE ASSEMBLY 4 A531-026 TOGGLE SWITCH 17 A535-059 TANK HTR 6.6 KW @ 240V 5 A549-006 LIQUID LEVEL CONTROL BRD 18 A712-046 THERMOS
Summary of the content on the page No. 15
Parts Illustration for Model RAP400E Item Part # Description Item Part # Description 1 A548-072 LEG, RUBBER (RAP400) 11 A515016 PILOT LIGHT 1 A545-004 LEG, PLASTIC 4” (OPTIONAL RAP 400) 12 A725-082 SPRAY TEE KIT W/ BYPASS PLUG 1 A548-090 LEG, PLASTIC PLUG (RAP300) 13 A530-009 BREW TIMER 0-8 MINUTES SILICONE TUBING 3/8”ID X 5/8”OD X 6”LG 2 A531-035 TERMINAL BLOCK 14 A585-021 3 A549-006 LIQUID LEVEL BOARD 15 A712-018 ELECTRODE ASSEMBLY 4 AAP-3 AIRPOT 16 A535-059 TANK HTR 6.6 KW @ 240V 5 APT400-105
Summary of the content on the page No. 16
Parts Illustration for Model RAPS400E Item Part # Description Item Part # Description BRASS SPRAY TEE W/ BYPASS TUBING 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 16 A725-081 SPRAY TUBING 3/8” ID X 5/8”OD X 6”LG 1 A545-015 LEG, 4” SS (OPTIONAL) 17 A585-021 2 A537-043 HOT WATER FAUCET W/ NUT 18 A712-018 ELECTRODE ASSEMBLY 3 A531-035 TERMINAL BLOCK 19 A535-010 TANK HEATER 5KW @ 240V 4 AABW-R ACCESSORY WARMER RIGHT 20 A712-046 THERMOSTAT W/ GROMMET 5 AAP-3 AIRPOT 3 LITER 21 A515027 DPST POWER RELAY 6 A
Summary of the content on the page No. 17
Parts Illustration for Model VSB-400 Item Part # Description Item Part # Description SPRAY TEE KIT W/ BYPASS TUBING 1 A545-034 LEG, 4” PLASTIC W/ SS FOOT 12 A725-081 1 A545-015 LEG, 4” SS (OPTIONAL) 13 A530-009 BREW TIMER 0-8 MINUTES 2 A531-035 TERMINAL BLOCK 14 A585-021 SILICONE TUBING 3/8”ID X 5/8”OD X 6”LG 3 A549-006 LIQUID LEVEL BOARD 15 A712-018 ELECTRODE ASSEMBLY 4 AVS-1.5 SHUTTLE VACUUM 16 A535-059 TANK HEATER 6.6 KW @ 240V 5 APT400-105 SPRAY HEAD 17 A712-046 THERMOSTAT W/ GROMMET 6 ABB1
Summary of the content on the page No. 18
Parts Illustration for Shuttle CS-LL 5 6 4 Item Part # Description 1 A537-053 FAUCET MODEL ES 3 2 A522078 SHANK W/ CHROME BONNET 3 A718-018 GAUGE ASSEMBLY 4 A725-092 KIT, SHUTTLE LID 2 SS SHUTTLE COVER A713-027 (not shown)* 1 5 A548-142 LID RETAINING CLIP A548-140 6 LID STOPPER W/ O-RING A61365 * S.S. Cover used until August 2001 A318-119P TOP GAGE FITTING A537-055 HANDLE A522026 WASHER UPPER GAGE A555-001 GAGE SHIELD A522132 BONNET NUT A522031 GAGE GLASS A522120 SPRING A537-047 PLASTIC STEM A5
Summary of the content on the page No. 19
Rough-In Drawing for Model P-300 Page 19 Shuttle Brewers & Airpot/Shuttle Brewers
Summary of the content on the page No. 20
Rough-In Drawing for Model P-400 Page 20 Shuttle Brewers & Airpot/Shuttle Brewers
