Bunn A10A Automatic user manual

Summary of the content on the page No. 1

A10 Automatic &
A10A Automatic
Supplement to A10 Use & Care
Booklet #10070.0000
INSTALLATION & OPERATION
INTRODUCTION
This equipment will automatically brew a 48 ounce batch of coffee into an awaiting decanter and has
a pour-over feature for emergency use. It is only for indoor use on a sturdy counter or shelf.
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“Bunn”) warrants the equipment manufactured by it to be commercially free from defects in material and
workmanship existing a

Summary of the content on the page No. 2

USER NOTICES The notices on this brewer should be kept in good condition. Replace unreadable or damaged labels. ! WARNING Fill water tank before turning -on thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles. FAILURE TO COMPLY RISKS EQUIPMENT DAMAGE, FIRE, OR SHOCK HAZARD READ THE ENTIRE OPERATING MANUAL BEFORE BUYING OR USING

Summary of the content on the page No. 3

ELECTRICAL REQUIREMENTS CAUTION - Do not plug-in the brewer until specified in Initial Set-Up. The A10 Automatic Brewer has an attached cordset and requires 2-wire grounded service rated 120 volts ac, 10 amp, single phase, 60 Hz. The A10A Automatic Brewer has an IEC 320 connector and matching cordset and requires 2-wire grounded service rated 230 volts ac, 10 amp, single phase, 50-60 Hz. The appropriate cordset connector must be supplied when installing the brewer. PLUMBING REQUIREMENTS This br

Summary of the content on the page No. 4

INITIAL SET-UP (CONT.) 8. If not, locate the brew timer near the heater switch on the left side of the brewer, adjust the brew timer dial up-or-down as required and allow the water to reheat. Start, and measure another brew cycle. 9. Repeat step 8 until 48oz water volume is achieved. 10. The brewer is now ready for use in accordance with the coffee brewing instructions. OPERATING CONTROLS Warmer Switch Placing the switch in the unlighted position cuts power to the brew station warmer and stops

Summary of the content on the page No. 5

REPLACEMENT PARTS 04060.0000 ........... BASE EXTRUSION 04067.0001 ........... SWITCH, LIGHTED ON/OFF 120V (A10) 04040.0004 ........... BREW FUNNEL, BLACK 04039.0000 ........... SWITCH, LIGHTED ON/OFF 240V (A10A) 04069.0003 ........... CONTROL THERMOSTAT ASSY. 21274.0000 ........... SWITCH, START 01716.0000 ........... CORD, POWER 250V 10 AMP, IEC320 (A10A) 04786.0002 ........... SWITCH, VACATION 01637.0000 ........... CORDSET, 16/3HSJO NEMA 5-15P (A10) 05518.0000 ........... SYPHON HUB 04123.00

Summary of the content on the page No. 6

SCHEMATIC WIRING DIAGRAM A10 AUTO GREEN L1 N SW. & LIMIT LIMIT THERMOSTAT SW1 THERMOSTAT THERMOSTAT 1000W BLK BLU BLK WHI TANK HEATER 40W WHI WHI SW2 "KEEP WARM" HEATER WHI 80W WHI WHI BLK LOWER WARMER SW3 BLK SOL HALF BATCH OPTION BLK GRY 1 WHI SW4 2 PNK ORA 3 BREW WHI/GRN 4 TAN TIMER YEL 5 120 VOLTS AC 2 WIRE 10628.0001A 5/92 © 1991 BUNN-O-MATIC CORPORATION SINGLE PHASE SCHEMATIC WIRING DIAGRAM A10 A AUTO GRN/YEL L1 L2 SW. & LIMIT LIMIT THERMOSTAT SW1 THERMOSTAT THERMOSTAT 1000W BLK BL