Summary of the content on the page No. 1
CLUB SERIES LAT PULLDOWN
ASSEMBLY INSTRUCTIONS
Part # 6941801 1 Revision:08/02/00
Rev A.
Summary of the content on the page No. 2
PARTS LIST KEY PART # DESCRIPTION QTY KEY PART # DESCRIPTION QTY 1 69046xx ASSY TOWER 1 9 3102922 3/8 X 2-3/4” BOLT 8 1A 6920001 CABLE 1 10 3102905 3/8 X 3-3/4” BOLT 4 1B 6714901 GUIDE ROD BUSHINGS 2 11 3102807 3/8” LOW HEIGHT LOCK NUT 10 2 69032xx WLDMT, MAIN UPRIGHT 1 12 6957001 WEIGHT STACK LABEL 1 2A 6692601 3 X 2 END CAP 1 13 3102514 3/8” SAE WASHER 8 2B 6902201 SUPPORT HOOK CHROME 1 14 6866701 3/8” RH WASHER 22 2C 3222801 4.5" PULLEY 3 15 6913801 WEIGHT STACK SELECTOR PIN 1 2D 3102933 3/8-
Summary of the content on the page No. 3
1 1B 11 10 3/8 X 3-3/4” 14 3 27 FIGURE 1 STEP 1: • LOOSELY assemble the TOWER (1) to the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 1. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 4
Summary of the content on the page No. 4
2E 2D 2L 1A 2M 2K 2A 2N 2G 2J 2C 2F 2I 2B 2H 1A 2
Summary of the content on the page No. 5
1A 1B 2 11 14 13 9 3/8 X 2-3/4 27 3 3/8 X 3-3/4” 10 FIGURE 2 STEP 2: • LOOSELY assemble the MAIN UPRIGHT (2) to the base of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 3-3/ 4” BOLTS (10), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 2. • LOOSELY assemble the MAIN UPRIGHT (2) to the top tube of the BENCH FRAME (3) using four RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGH
Summary of the content on the page No. 6
FIGURE 3 1A 17 9 3/8 X 2-3/4” 13 5B 14 5C 5 5A 5D 3 11 27 STEP 3: • SECURELY assemble the KNEE SUPPORT (5) to the BENCH FRAME (3) using two BLACK RH CAPS (17), two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” SAE WASHERS (13), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 3. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 6
Summary of the content on the page No. 7
5A 18 3 14 3/8 X 2-3/4” 9 27 FIGURE 4 STEP 4 • SECURELY assemble the SEAT PAD (18) to the BENCH FRAME (3) using two RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9) and two 3/8” RH WASHERS (14) as shown in FIGURE 4. 7
Summary of the content on the page No. 8
FIGURE 5 6 20 1 19 15 8 26 24 1A 24 25 16 HEAVY WEIGHT OPTION STEP 5: • Insert the two GUIDE RODS (26) (found in the SHROUD KIT) into the base of the TOWER (1) as shown in FIGURE 5. Lubricate the GUIDE RODS (26) with a slicon or teflon spray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (16) down over the GUIDE RODS (26). See FIGURE 5. • Using EXTREME CARE place twenty 10 LB. WEIGHT PLATES (24) over the GUIDE RODS (26) as shown in FIGURE 5. (NOTE: If HEAVY WE
Summary of the content on the page No. 9
11 FIGURE 6 1 14 9 3/8 X 2-3/4” 27 2 6 20 19 TIGHTEN! 26 1A 8 24 15 STEP 6: • SECURELY assemble the GUIDE ROD SUPPORT (6) to the TOWER (1) and MAIN UPRIGHT (2) using four RH CAPS (27), two 3/8 X 2-3/4” BOLTS (9), four 3/8” RH WASHERS (14) and two 3/8” LOW HEIGHT LOCK NUTS (11) as shown in FIGURE 6. • Slide GUIDE ROD BUSHINGS (20) into the tubes on the GUIDE ROD SUPPORT (6), slide 1” SHAFT COLLARS (19) under- neath the GUIDE ROD BUSHINGS (20) and SECURELY tighten the set screws. • Inser
Summary of the content on the page No. 10
TIGHTEN! FIGURE 7 8 24 12 ST````` • The WEIGHT STACK LABEL sheet (12) includes labels for both lbs. and kgs. for both the standard and optional weight stacks. • Peel the backing off the WEIGHT STACK LABELS (12), line up sheet to the right of the selector opening and apply labels to the WEIGHT PLATES (24), starting with the HEAD PLATE (8) as shown in FIGURE 7. • REFER TO SHROUD KIT ASSEMBLY INSTRUCTIONS. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 34 5 6 10
Summary of the content on the page No. 11
32 22 23 31 4 21 29 7 4A FIGURE 8 STEP 8: • Assemble the PLACARD LABEL (22) or the FOREIGN LANGUAGE PLACARD LABEL (23) to the FRONT SHROUD as shown in FIGURE 8. • Attach LAT BAR (4) and/or TRICEP ROPE (7) end of cable using on SNAP LINK (21) with the TRICEP ROPE (7) as shown in FIGURE 8. 11
Summary of the content on the page No. 12
12 27S 30 29 1 28 3/8 X 3-1/2” FIGURE 8 STEP 8: (NOTE: If the PARTIAL SHROUD KIT is being used follow STEP 8. If the FULL SHROUD KIT is being used follow STEP 9.) • SECURELY assemble the FRONT PARTIAL SHROUD (29) and the REAR PARTIAL SHROUD (30) to the TOWER (1) using twelve 3/8 X 3-1/2” BUTTON HEAD BOLTS (28), twelve STARLOCK WASHERS (27), and twelve 3/8” ACORN NUTS (12) as shown in FIGURE 8. 11
Summary of the content on the page No. 13
27 12 32 1 31 3/8 X 3-1/2” 28 FIGURE 9 STEP 9: • SECURELY assemble the FRONT FULL SHROUD (31) and the REAR FULL SHROUD (32) to the TOWER (1) using ten 3/8 X 3-1/2” BUTTON HEAD BOLTS (28), ten STARLOCK WASHERS (27), and ten 3/8” ACORN NUTS (12) as shown in FIGURE 9. 1/2 1/2 1/2 1/2 1/2 1/2 0 1 2 3 4 5 6 12
Summary of the content on the page No. 14
CAUTION-PLEASE READ There is a risk assumed by individuals who use this type of equipment. To minimize risk, please follow these rules: 1. Inspect equipment daily. Tighten all loose connections and replace worn parts immediately. Failure to do so may result in serious injury. 2. Do not allow minors or children to play on or around this equipment. 3. Exercise with care to avoid injury. 4. Consult your physician before beginning any exercise program. WARRANTY INFORMATION 10 YEARS STRUCTURUAL F
