Summary of the content on the page No. 1
NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
COMPETITOR
Safety Notice
WM-343 BENCH
Hardware Identifier
Assembly Instruction
Exploded Diagram
Parts List
Warranty
Ordering Parts
Model
WM-343
Retain This
Manual for
Reference
May 29, 2001
IMPEX INC.
14777 Don Julian Rd., City of Industry, CA 91746
OWNER'S Tel: (800) 999-8899 Fax (626) 961-9966
www.impex-fitness.com
MANUAL
info@im
Summary of the content on the page No. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...............................................................................................1 IMPORTANT SAFETY NOTICE................................................................................2 HARDWARE IDENTIFIER.........................................................................................3 ASSEMBLY INSTRUCTIONS....................................................................................4 EXPLODED DIAGRAM...............
Summary of the content on the page No. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one perso
Summary of the content on the page No. 4
3
Summary of the content on the page No. 5
ASSEMBLY INSTRUCTION Tools required to assembly the machine: Two Adjustable Wrenches STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#25) in the Mid-span. Fasten them by two M10x 2 3/8” Bolts (#14), four ∅ 7/8” Washers (#13), one Bracket (#12), and two M10 Aircraft Nuts (#15) on each side of the Cross Brace. DO NOT tighten the nuts and bolts yet. B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to o
Summary of the content on the page No. 6
STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#49) to the Main Seat Support (#32) and secure them with two M10 x 1” Bolts (#42), four ∅ 7/8” Washers (#13), and two M10 Aircraft Nuts (#15). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#32) to the Cross Brace (#25) and secure it with two M10 x 2 3/8” Bolts (#14), four ∅ 7/8” Washers (#13), one Bracket (#12), and two M10 Aircraft Nuts (#15). C.) Connect one end o
Summary of the content on the page No. 7
STEP 3 (SEE DIAGRAM 3) A.) Attach a ∅7/8” Washer (#13) onto a M10 x 4 ½” Bolt (#24). Insert the Bolt through the Butterfly (#22). Place a M10 Regular Nut onto the Bolt. Then insert the Bolt through the hole on the Rear Upright Beam (#1). Secure the Bolt with a Knob (#11) behind the Upright Beam. Repeat the same step to install the other Butterfly. B.) Attach the Left Butterfly Handle (#19) to the Left Butterfly (#22). Secure it with a M10 x 2 ¼” Bolt (#18), ∅ 7/8” Washer (#13),
Summary of the content on the page No. 8
STEP 4 (SEE DIAGRAM 4) A.) Attach the hole-side of the Backrest Supports (#28) onto both ends of the Pivot on the Main Seat Support (#32). The other side rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#33) onto the Backrest Support (#28). Fasten it with four M6 x 1 3/8” Bolts (#31) and ∅ ½” Washers (#30). C.) Place Seat Cushion (#34) onto the bracket on the Main Seat Support (#32). Align the holes and fasten the Seat with four M6
Summary of the content on the page No. 9
Summary of the content on the page No. 10
PARTS LIST KEY NO. DESCRIPTION QUANTITY 1 Rear Upright Beam 2 2 Right Bar Catch 1 3 Curl Bar 1 4 Spring Clip 3 5 Æ Æ1” Curl Bar Flat End Cap 2 6 Left Bar Catch 1 7 Bar Catch Panel 2 8 7/8” Flat End Cap 2 9 1 ½” Square End Cap 12 10 Backrest Adjustment Bar 1 11 Knob 2 12 Bracket 3 13 Æ Æ 7/8” Washer 20 14 M10 x 2 3/8” Bolt 6 15 M10 Aircraft Nut 10 16 1 1/8” Plastic Stopper 2 17 3/8” Bushing 10 18 M10 x 2 ¼” Carriage Bolt 2 19 Left Butterfly Handle 1 20 Grip 2 2
Summary of the content on the page No. 11
IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
