Summary of the content on the page No. 1
��
� � � � � � � � � � �
��
Please read this manual and save it
with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver,
Adjustable Wrench (or Pliers) and
Safety Scissors (all not included).
®
Use only with a Power Wheels 12 Volt
Lead Acid Rechargeable Battery and
®
Power Wheels 12 Volt Charger
with Type 12V Connector (both included).
Requires three "AA" (LR6) alkaline
batteries for sound box operation.
Product Product features
Summary of the content on the page No. 2
T TABLE ABLE OF OF CONTENTS CONTENTS A A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . .
Summary of the content on the page No. 3
WARNINGS AND CAUTIONS B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery clamp. • PREVENT FIRE - Ne ver modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could c
Summary of the content on the page No. 4
PARTS C • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Windshield Vehicle Hood with Fl
Summary of the content on the page No. 5
TABLE OF PARTS CONTENTS A C 1 #10 x / " Screw – 8 2 12 Volt Battery 12 Volt Charger #8 x 1" Screw – 9 Taillight Lens Set #10 x 1" Screw – 5 Taillight Housing Set 5 1 / " x 1 / " Pin - 1 32 2 #8 x 4" Screw – 2 Lens Guard - 2 Headlight Lens - 2 #8-32 x 1.625" Screw – 2 #8 Acorn Lock Nut – 2 Hood Latch – 2 Light Cover – 2 5 #8 x / " Screw – 1 8 3 / " Washer – 1 8 Water Bottle in Key Assembly Drink Holder with #8 Lock Nut – 1 Decorative Hair Tie - 2 For your convenience, we included extra fast
Summary of the content on the page No. 6
TABLE PARTS OF PICTURE CONTENTS D A Note: Some parts shown are assembled on both sides of the vehicle. 25 23 24 15 21 1 4 19 26 14 1 7 22 28 6 1 1 9 1 8 8 7 10 12 4 3 8 1 3 30 29 3 20 27 1 1 6 2 5 Parts Not Shown 1 Vehicle 11 Dash 21 Sport Bar 2 Steering Column 12 Headlight Lens 22 Sport Bar Support - 2 #8 x 1" Screw - 9 #8 Acorn Lock Nut - 2 3 Hood Latch 13 Lens Guard 23 Light Cover - 2 #10 x 1" Screw - 5 #8 Lock Nut - 1 1 3 4 12 Volt Battery 14 Short Seat Belt Strap 24 Steering Wheel Cove
Summary of the content on the page No. 7
BATTERY CHARGING E ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a child if Use the charger in dry locations only. vehicle tips over. Always use battery clamp. • PREVENT FIRE About Thermal Fuses - Ne ver modify the electrical system. Your Power Wheels 12 volt battery is equipped with a built-in Alterations could cause a fire resulting thermal fuse. The thermal fuse is a self-resetting safety device which in serious injury and could also ruin the automatically “trips”
Summary of the content on the page No. 8
BATTERY CHARGING E F ASSEMBLY WARNING Children can be harmed by small parts, sharp edges and sharp points in the B 12V Battery vehicle's unassembled state, or by electrical items. Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or A help in assembly of the vehicle. Charger Connector Dash A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . Note: If power flow to the w
Summary of the content on the page No. 9
ASSEMBLY F B B A 1.5V x 3 B "AA" (LR6) Dash A Shown Actual Size Battery Safety Information Motor In exceptional circumstances, batteries may leak fluids that can cause Harness a chemical burn injury or ruin your product. To avoid battery leakage: Connector • Do not mix old and new batteries or batteries of different types: Wire alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium). • Insert batteries as indicated inside the battery compartment. • Remove batteries during long p
Summary of the content on the page No. 10
ASSEMBLY F Key Tab UP Assembly Steering Dash Column Steering Wheel Large Opening UP 6 Side View 8 • Insert and “snap” the key assembly into the opening in the dash, as shown. • Position the steering wheel so that the large opening and the tab on the steering wheel stem are both UP. • Fit the steering wheel onto the end of the steering column. 5 1 / " x 1 / " Pin 32 2 End of Steering Column Hole Steering Column 9 5 1 • Insert the / " x 1 / " pin through the hole in the end of the 32 2
Summary of the content on the page No. 11
ASSEMBLY F End of Steering Steering Wheel Column Cover 3 " / Washer 8 Tabs Steering Rod Hole Steering Wheel Bottom View 11 • Turn the vehicle on its side. Tab Tab • Insert the end of the steering column through the hole in the Bottom steering rod. Side View 13 Spoke 3 " • Place the / washer on the end of the steering column. 8 • Position the steering wheel cover so the fastener tabs are towards the bottom of the steering wheel. • Fit the steering wheel cover over the steering wheel. •
Summary of the content on the page No. 12
ASSEMBLY F Slot Grille Tab Flying Disc Plastic Tie Slot Tab Front View 15 Hood • Fit the lens tabs on the back of a lens assembly into the headlight slots in the grille. Plastic Tie • Press firmly to "snap" the lens assembly into the grille. 17 • Repeat this procedure to "snap" the other lens assembly into the grille. • Using safety scissors, cut the plastic ties holding the flying disc on the hood. Dispose of the plastic ties properly. Note to Retailer: Do not remove the plastic ties. Hood
Summary of the content on the page No. 13
ASSEMBLY F Windshield A Spacers Wipers Large Large Tab Tab Large Slot Large Slot 19 • Position the windshield so that the molded detail on the wipers #8 x 4" faces the front end of the vehicle. B Screws • Insert and “snap” the two large tabs on the windshield into the 21 large slots in the dash. • Pull up on the windshield to be sure it is secure. • Fit two spacers between the upper holes of the brush guard and the A front end of the vehicle . • Insert two #8 x 4" screws through the u
Summary of the content on the page No. 14
ASSEMBLY F Long Seat Belt Strap T-Loop Fastener End 23 • Insert each fastener end of the long seat belt strap through a slot in Back View the center of the seat. Make sure the fasteners face the outer edge 25 of the seat. • Pull each side of the long seat belt strap evenly through the slots. • Insert a #8 x 1" screw into the rear edge of the seat. Tighten Make sure to pull each T-loop through a slot. the screw. • Turn the seat upright. Seat Seat Cover Seat Back Tabs Tabs PUSH B HERE C S
Summary of the content on the page No. 15
ASSEMBLY F Sport Bar Water Bottle with Drink Holder Supports 29 Side View 27 • Fit a support to one side of the sport bar. • Place the tab on the side of the seat cover over the hole on the top " • Insert a #8- 32 x 1.625 screw through the support, the sport bar edge of the vehicle. and out through the support. • Fit a water bottle with drink holder on top of the tab and the top edge • Fit a #8 acorn lock nut to the end of the screw. of the vehicle. • While holding the acorn lock nut with
Summary of the content on the page No. 16
ASSEMBLY F Taillight Housing Sport Bar Support PUSH HERE Side Fender Taillight Lens #8 x 1" Screws PULL HERE Back View 33 • Turn the vehicle upright. 31 • Using safety scissors, remove the taillight lenses and the taillight housings from the plastic connectors. Dispose of the plastic • Fit the sport bar assembly into the holes in the top side of connectors. the vehicle. • Face the rear of the vehicle. • Push down firmly on a sport bar support while pulling up on the side • Fit a tailli
Summary of the content on the page No. 17
TABLE DECORA OF CONTENTS TION A G Proper label application will help to keep the labels looking their best! When applying labels, keep the following guidelines in mind: • Wash your hands before applying the labels. • Before applying the labels, wipe the surface of the vehicle with a clean, dry cloth to remove any dust or oils. • Place the labels exactly as shown in the illustrations. • For best results, avoid repositioning a label once it has been applied to the vehicle. • After applying a lab
Summary of the content on the page No. 18
DECORATION G 7 7 9 6 1 16 6 FRONT LEFT SIDE 9 6 17 2 16 6 FRONT RIGHT SIDE 18 H4433pr-0920
Summary of the content on the page No. 19
BATTERY INSTALLATION H ® IMPORTANT! Use only a Power Wheels 12 volt lead-acid rechargeable battery. Use of any other battery will damage your vehicle. Make sure that you charge the battery for at least ® 18 hours using the enclosed Power Wheels 12 volt charger before Motor Harness operating your vehicle for the first time. Charge the battery for at Connector least 14 hours after each use of the vehicle. Never charge the battery longer than 30 hours. Failure to follow these instruction
Summary of the content on the page No. 20
BATTERY CARE AND DISPOSAL I Care Disposal ® If a battery leak develops, avoid contact with the leaking acid and • Your Power Wheels battery is a non-spillable sealed lead-acid place the damaged battery in a plastic bag. See information below battery. It must be recycled or disposed of in an environmentally for proper disposal. sound manner. If acid comes in contact with skin or eyes, flush with cool water for • Do not dispose of a lead-acid battery in a fire. The battery may at least 15
