Summary of the content on the page No. 1
MODEL W1775
NAILER/STAPLER KIT
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC., REVISED DECEMBER, 2007 (JM)
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9568BL Printed in China
Summary of the content on the page No. 2
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ��������������������������������������������������������������� � �������� �����������������������������������������������������
Summary of the content on the page No. 3
Model W1775 Nailer/Stapler Kit SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accide
Summary of the content on the page No. 4
Model W1775 Nailer/Stapler Kit Safety Instructions for Pneumatic Tools 10. USE PROPER AIR HOSE for the 17. DISCONNECT TOOLS before tool. Make sure your air hose is in servicing, changing accessories, or good condition and is long enough moving to another location. to reach your work without 18. DO NOT OVERREACH. Keep proper stretching. footing/balance at all times. 11. WEAR PROPER APPAREL. Do 19. USE THE RECOMMENDED not wear loose clothing, gloves, ACCESSORIES. Consult owner’s neckties,
Summary of the content on the page No. 5
Model W1775 Nailer/Stapler Kit Additional Safety for Nailers/Staplers 1. HAND INJURIES: Do not place your 5. HOSE USAGE: Make sure your air hands near the nail/staple point hose is designed for the tool in of entry. A nail/staple can deflect use, is in good condition, and is and tear through the surface of the long enough to reach your work workpiece, puncturing your hand or without stretching. However, an fingers. overly long air hose in the work area may be a tripping hazard. 2. COMBUST
Summary of the content on the page No. 6
Model W1775 Nailer/Stapler Kit INTRODUCTION Woodstock Technical Tool Data Support 5 Brad Length ............... ⁄8"-2" (18 Gauge) 5 5 Staple Length ........................ /8"-1 ⁄8" This tool has been specially designed 1 Staple Crown ................ ⁄4" (18 Gauge) to provide many years of trouble-free Magazine Capacity ................100 pieces service. Close attention to detail, Air Inlet .................................¼" NPT ruggedly built parts and a rigid quality Weight ..........
Summary of the content on the page No. 7
Model W1775 Nailer/Stapler Kit Compressed Air System The Model W1775 is designed to be operated at 60-100 PSI using clean, dry, regulated, compressed air. Do not exceed the 120 PSI maximum operating pressure for your model. Before using your new nailer/stapler, regulate the air pressure to find the optimum setting within the specified operating range. Start by testing the nailer/stapler at a low setting, then Exceeding the maximum permissible increase the air pressure as needed for op
Summary of the content on the page No. 8
Model W1775 Nailer/Stapler Kit SETUP Unpacking This tool has been carefully packaged for safe transportation. If you notice the tool has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1775. Lay the components out to inventory them. Note: If you can't find an item on this list, check the mounting location on the tool or examine the packaging materials carefully.
Summary of the content on the page No. 9
Model W1775 Nailer/Stapler Kit — If the nailer/stapler fires when Safety Nose Mechanism the trigger is pulled, without the A safety mechanism on the nose of the safety nose mechanism being nailer/stapler protects against accidental depressed, then the nailer/stapler firing. When the trigger is pressed, the is not working properly. nailer/stapler will not fire until the safety nose mechanism is depressed. — If you find that the safety nose mechanism is not working prop- Before you use your
Summary of the content on the page No. 10
Model W1775 Nailer/Stapler Kit OPERATIONS Loading When replacing brad nails in your Model W1775, follow these guidelines: Pusher Gauge: 18 5 Brad Length: ⁄8"-2" Magazine 5 5 1 Staple Length: ⁄8"-1 ⁄8" (crown ⁄4") Capacity: 100 Sight Window To load your nailer/stapler, do these Figure 4. Loading nails into magazine. steps: 4. Slide the staples or brads all the way down to the nose of the nailer/sta- 1. DISCONNECT NAILER/STAPLER FROM pler. THE AIR SUPPLY! 5. Push the magazine toward the nose
Summary of the content on the page No. 11
Model W1775 Nailer/Stapler Kit 2. To test for proper nail penetration, — If the nail/staple either went too hold the nailer/stapler perpendicular far or not far enough, then go to to the surface of a piece of clean the Adjusting Depth section on scrap wood that is thick enough for this page. the length of nails/staples you have loaded. Adjusting Depth 3. Depress the safety nose mechanism A depth adjustment knob is attached against your workpiece. to the nose for setting the nail/staple d
Summary of the content on the page No. 12
Model W1775 Nailer/Stapler Kit To clear a jammed nail from the dis- Clearing Jammed Nails charge area, do these steps: A jammed nail or staple must be cleared before using the nailer/stapler again. 1. DISCONNECT NAILER/STAPLER FROM THE AIR SUPPLY! To clear a jammed nail or staple from the magazine, do these steps: 2. Unlock the catch lever and pull the magazine pusher back completely. 1. DISCONNECT NAILER/STAPLER FROM THE AIR SUPPLY! 3. Remove the nail/staple stick from the magazine. 2.
Summary of the content on the page No. 13
Model W1775 Nailer/Stapler Kit 6. Open the nose cover as if to clear a Replacing Piston and jammed nail/staple. O-Rings 7. Watch the discharge area and push Under heavy use, a piston or piston shaft the top of the piston with your may wear out. Replacement is quick and finger. You will see the piston shaft easy. Contact your authorized Shop Fox slide down the discharge area. dealer to obtain the Piston Repair Kit (part number X1775001). 8. Taking care not to scratch or dent the nailer
Summary of the content on the page No. 14
Model W1775 Nailer/Stapler Kit CLEANING & LUBRICATION Cleaning Lubricating Disconnect the nailer/stapler from the Standard pneumatic tool oil has been air supply before cleaning. Use a good included with your new Shop Fox nailer/ solvent to clean the nose assembly of the stapler to help maintain its useful life. nailer/stapler. Always be sure that the Place two to three drops of oil in the nailer/stapler is dry before using it again. nailer/stapler air inlet (as shown in Figure 8) before ev
Summary of the content on the page No. 15
Model W1775 Nailer/Stapler Kit PARTS BREAKDOWN � � �� � �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� � �� � � �� � � � � � �� � � � � � � -13-
Summary of the content on the page No. 16
Model W1775 Nailer/Stapler Kit PARTS LIST REF PART � # DESCRIPTION REF PART � # DESCRIPTION 1 X1775001 PISTON � REPAIR �KIT 44 X1775044 RETAINER �SNAP 2 X1775002 CARRYING � CASE 45 X1775045 STAND � PLATE 3 XPAW04M HEX � WRENCH � 4MM 46 XPEC12M E-CLIP� 12MM 4 XPAW03M HEX � WRENCH � 3MM 47 X1775047 COMRESSION �SPRING 5 XPLW02M LOCK � WASHER �4MM 48 X1775048 STAND 6 X1775006 AIR � PLUG � COVER 49 XPRP12M ROLL � PIN�2.5�X �18 7 X1775007 1/4" � NPT � MALE �CONNECT 50 X1775050 SAFETY �PLATE 8 X177500
Summary of the content on the page No. 17
Model W1775 Nailer/Stapler Kit Troubleshooting Symptom Possible Cause Cause Possible Solution Air leaking at 1. O-rings in trigger valve housing 1. O-rings must be replaced trigger valve area. are damaged. & operation of safety nose must be checked. Air leaking 1. Loose screws in housing. 1. Reseal and tighten screws. between housing 2. Damaged O-ring. 2. Replace O-ring and hose 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. Air leaking 1. Damaged seal. 1. Replace damaged sea
Summary of the content on the page No. 18
� � � � � � � �� � � �� � � � � � � � � � � � � � � ��� � � � � � � � � � � � � � �� � � � �� � � � � � � � �� � � �� � � � � � � � � �� � � ��� � � � �� � �� � �� � � � �� � �� � � � � � � �� � � � �� � � � � � � � � � ��� � � �� � � � � � � � � �� � � �� �� � � � � � �� � �� �� � � � �� � � � �� � � �� � � � �� � �� � � � � �� � �� � � � �� � � � �� � � �� � � � � � � � � �� � � � � �� � � � �� � � � � � � � �� � � � � �� � � �� � � � � � �� � � �� � � � �� � � �� � � � � �� � � ��� � � �� � �
Summary of the content on the page No. 19
Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________ The following informa
Summary of the content on the page No. 20
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309 FOLD ALONG DOTTED LINE TAPE ALONG EDGES--PLEASE DO NOT STAPLE
