Weider WESY96352 user manual

User manual for the device Weider WESY96352

Device: Weider WESY96352
Category: Home Gym
Manufacturer: Weider
Size: 1.15 MB
Added : 6/15/2013
Number of pages: 33
Print the manual

Download

How to use this site?

Our goal is to provide you with a quick access to the content of the user manual for Weider WESY96352. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Weider WESY96352.

For your convenience

If looking through the Weider WESY96352 user manual directly on this website is not convenient for you, there are two possible solutions:

  • Full Screen Viewing - to easily view the user manual (without downloading it to your computer), you can use full-screen viewing mode. To start viewing the user manual Weider WESY96352 on full screen, use the button Fullscreen.
  • Downloading to your computer - You can also download the user manual Weider WESY96352 to your computer and keep it in your files. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase.
Weider WESY96352 User manual - Online PDF
Advertisement
« Page 1 of 33 »
Advertisement
Print version

Many people prefer to read the documents not on the screen, but in the printed version. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Weider WESY96352 but the selected pages only. paper.

Summaries

Below you will find previews of the content of the user manuals presented on the following pages to Weider WESY96352. If you want to quickly view the content of pages found on the following pages of the manual, you can use them.

Abstracts of contents
Summary of the content on the page No. 18

36. Attach the Press Bracket (94) to the Leg 36 Press Arm (96) with a 5/16” x 3” Bolt (75) and a 5/16” Nylon Locknut (3). Wrap the Leg Press Cable (99) around a 3 1/2” Pulley (15). Attach the Pulley to the Press Bracket (94) with the 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). 96 Slide a 5/16” Flat Washer (8) onto a 5/16” x 2 3/4” Bolt (11). Insert the Bolt through the 12 lowest hole in the Rear Seat Frame (100) 3 11 from the indicated side. (Note: The three 8 94 holes are for cable adju

Summary of the content on the page No. 19

39. Attach the Front Backrest (41) to the Front 39 42 Upright (42) with two 1/4” x 2 1/2” Screws (43) and two 1/4” Flat Washers (10). The Backrest must be oriented as shown. 41 10 43 40. Press a 1 1/2” Square Inner Cap (32) into the Thick End Front Seat Frame (36). Insert a 1/4” x 2” Carriage Bolt (38) through 40 the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4” x 13 3/4” Screws (18). Insert the 1/4” x 2” Carriage Bolt (38) through 38 the indicated ho

Summary of the content on the page No. 20

43. Press two 3/4” Round Inner Caps (34) into 43 each Pad Tube (28). Insert a Pad Tube (28) into the Seat Frame (36). Slide a Foam Pad (30) onto each end of 30 the Pad Tube. 34 28 Insert the other Pad Tube (28) into the Leg Lever (29). Slide a Foam Foam Pad (30) onto 34 29 each end of the Pad Tube. 30 44. Locate and open the parts bag labeled 44 “VKR ASSEMBLY.” 75 80 Press 1 1/2” Square Inner Caps (32) into the ends of the Left VKR Arm (79) and the Right VKR Arm (80). 3 74 Attach the Left VKR

Summary of the content on the page No. 1

Model No. WESY96352
Serial No.
Write the serial number in the space
above for reference.
USER'S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-

Summary of the content on the page No. 2

TABLE OF CONTENTS IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 HOW T

Summary of the content on the page No. 3

IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the home gym system. 1. Read all instructions in this manual and in 8. Keep hands and feet away from moving parts. the accompanying literature before using the home gym system. 9. Do not use the VKR station when either weight stack is in use. 2. It is the responsibility of the owner to ensure that all users of the home gym system are 10. Always wear athletic shoes for foo

Summary of the content on the page No. 4

BEFORE YOU BEGIN ® Thank you for selecting the versatile WEIDER PRO Customer Service Department toll-free at 1-800-999- 9635 Home Gym System. The PRO 9635 offers a 3756, Monday through Friday, 6 a.m. until 6 p.m. selection of weight stations designed to develop every Mountain Time (excluding holidays). To help us assist major muscle group of the body. Whether your goal is you, please note the product model number and serial to tone your body, build dramatic muscle size and number before calling.

Summary of the content on the page No. 5

ASSEMBLY Before beginning assembly, carefully read the • As you assemble the PRO 9635 be sure that all following information and instructions: parts are oriented as shown in the drawings. • Place all parts of the PRO 9635 in a cleared area • Tighten all parts as you assemble them, unless and remove the packing materials; do not dis- instructed to do otherwise. pose of the packing materials until assembly is completed. THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY: • The assembl

Summary of the content on the page No. 6

2. Slide the VKR Upright (74) and the Leg Press 2 27 Upright (56) onto the indicated 5/16” x 2 1/2” 27 Carriage Bolts (1) in the Stabilizer (5). The high side of the brackets on the VKR Upright and Leg Press Upright should be on the side shown. Hand-tighten four 5/16” 87 Nylon Locknuts (3) onto the Carriage Bolts. High Sides Do not tighten the Nylon Locknuts yet. of Brackets 91 74 Press two 2” Square Inner Caps (27) into the 56 Leg Press Upright (56). Press a 2” Square 27 Inner Cap into the VKR

Summary of the content on the page No. 7

4. Press a 2” Square Inner Cap (27) into the end 11 4 49 55 of the Top Frame (55). Press a 1 3/4” Square 44 Inner Cap (44) into each end of the crossbar 8 on the Top Frame. Press two 1” Round Inner 27 Caps (49) into the top of the crossbar. 3 Attach the Top Frame (55) to the VKR Upright (74) and the Leg Press Upright (56) with two Crossbar 44 5/16” x 2 3/4” Bolts (11) and two 5/16” Nylon Locknuts (3). 3 Attach the Top Frame (55) to the Front 11 Upright (42) with two 5/16” x 2 3/4” Bolts (11), t

Summary of the content on the page No. 8

7. Press a Weight Tube Bumper (64) into the 7 end of a Weight Tube (63). Insert the Weight Holes Tube into the front stack of Weights (25). Be sure that the pin on the Weight Tube is sit- 62 ting in the pin grooves in the top Weight. Lubricate the inside of the holes in a Top Weight (65). Set the Top Weight onto the front stack of Weights (25). Insert both Long Weight Guides (62) into the stack of Weights. Be sure that the holes in the Weight Guides are at the top, as shown. 65 Lubricate Pin 63

Summary of the content on the page No. 9

9. Attach the upper ends of the Short Weight 9 61 61 Guides (73) to the Top Frame (55) with a 5/16” 3 x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and 3 55 a 5/16” Nylon Locknut (3). 60 Attach the upper ends of the Long Weight Guides (62) to the Top Frame (55) with a 5/16” x 6” Bolt (60), two 1/2” x 3/4” Spacers (61), and 73 60 a 5/16” Nylon Locknut (3). 62 10. Locate and open the parts bag labeled 10 27 95 “ARM ASSEMBLY.” Welded Be sure there is a Bushing (98) in each side of Tube the Stabiliz

Summary of the content on the page No. 10

12. Press a 1” Round Inner Cap (49) into one of 12 44 49 the Press Arms (46). Press a 1 3/4” Square Inner Cap (44) into the Press Arm. Attach the Press Arm (46) to one side of the 46 Press Frame (17) with two 5/16” x 2 1/2” Bolts (22) and two 5/16” Nylon Locknuts (3). 22 Assemble the other Press Arm (46) in the same manner. 46 3 17 13. Identify the Right Arm (48) and the Left Arm 31 86 13 (47). Note the position of the welded bracket 50 on each Arm. Arm identification is very 31 important for st

Summary of the content on the page No. 11

15. See the inset drawing. Attach the Military 15 32 Press Arm (84) to the Pivot Arm (101) with 49 two 5/16” x 2 1/4” Bolts (33) and two 5/16” 32 Nylon Locknuts (3). Press two 1 1/2” Square Inner Caps (32) into the indicated end of the Military Press Arm (84). Press two 1” Round Inner Caps (49) into 21 the Military Press Arm. Slide two 5” Plastic 84 83 Grips (83) onto the Military Press Arm. 101 Attach the Military Press Arm (84) to the VKR 67 Upright (74) with a 3/8” x 3 1/4” Bolt (67) and a 3/

Summary of the content on the page No. 12

18. Wrap the High Cable (58) around a “V”-Pulley 18 (50). Attach the “V”-Pulley and a Long Cable 86 Trap (31) to the indicated bracket on the Front 31 58 Upright (42) with a 3/8” x 2 1/2” Bolt (86) and a 3/8” Nylon Locknut (21). Be sure that the 50 Long Cable Trap is positioned to hold the Cable in place. Bracket 42 21 19. Route the High Cable (58) around the “V”- 19 Pulley (50) on the Left Arm (47). Be sure that 31 86 the Cable is in the groove of the Pulley 50 and that the Long Cable Trap (31)

Summary of the content on the page No. 13

22. See the inset drawing. Attach a 3 1/2” Pulley 22 (15) and a Cable Trap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt 58 (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the Long “U”- 66 Bracket. Note: This may come pre-assem- 15 bled. 15 21 Route the High Cable (58) through the Long “U”-Bracket (57) and the 3 1/2” Pulley (15) 58 12 57 shown in the inset drawing. Be sure that the Cable is in the groove of the Pulley and that the Cable and Pul

Summary of the content on the page No. 14

25. Locate the Low Cable (23). Route the Low 25 Cable under the 3 1/2” Low Pulley (76) attached to the lower hole in the Press Frame 21 (17). Be sure that the end of the Cable with 76 the ball is on the indicated side of the Press Frame and that the Cable is between 23 the Pulley and the crossbar on the Press Ball Frame. Tighten the 3/8” Nylon Locknut (21) and the 3/8” x 3 3/4” Bolt (not shown). 17 Crossbar 26. Route the Low Cable (23) around the 3 1/2” 23 26 15 Pulley (15) attached to the lower

Summary of the content on the page No. 15

29. Attach the end of the Low Cable (23) to the 29 Long “U”-Bracket (57) with a 1/4” Nylon Locknut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are 57 showing above the Nylon Locknut, as 2 shown in the inset drawing. 2 10 23 10 57 23 30. Attach the High Cable (58) to a Small “U”- 30 Bracket (71) with a 1/4” Nylon Locknut (2) and a 1/4” Flat Washer (10). Do not completely tighten the Nylon

Summary of the content on the page No. 16

32. Wrap the Military Press Cable (72) around a 32 3 1/2” Pulley (15). Attach the Pulley to the Top 55 Frame (55) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). 15 See the inset drawing. Wrap the Long Cable 21 12 (72) around a 3 1/2” Pulley (15). Attach the Pulley and a Cable Trap (66) to the bracket 72 on the Stabilizer (5) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is turned to hold the Cable in place. 72 12 Bracket 66 15 21 5 33. Wrap the

Summary of the content on the page No. 17

34. See inset drawing A. Attach a 3 1/2” Pulley 34 (15) and a Cable Trap (66) to the upper hole 15 A in the Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be 21 66 sure that the Cable Trap is inside the Long “U”-Bracket. (Note: This may come pre- assembled.) 57 12 Route the Military Press Cable (72) through the Long “U”-Bracket (57) and the 3 1/2” B Pulley (15). Be sure that the Cable is in the groove of the Pulley and that the Cable 101 11 and Pulley move smooth


Alternative user manuals
# User manual Category Download
1 Weider 140 User manual Home Gym 106
2 Weider 150722 User manual Home Gym 35
3 Weider 148 User manual Home Gym 35
4 Weider 500 User manual Home Gym 16
5 Weider 220 User manual Home Gym 20
6 Weider 240 TC User manual Home Gym 19
7 Weider 16.8ST User manual Home Gym 5
8 Weider 5000 User manual Home Gym 16
9 Weider 28ST User manual Home Gym 10
10 Weider 740 User manual Home Gym 35
11 Weider 15CT User manual Home Gym 13
12 Weider 831.14622.0 User manual Home Gym 14
13 Weider 2000X WESY7773.1 User manual Home Gym 25
14 Weider 831.150280 User manual Home Gym 9
15 Weider 831.150291 User manual Home Gym 4
16 Aqua Leisure FF 6910 E User manual Home Gym 1
17 Aqua Leisure FF 6910 F User manual Home Gym 1
18 Aqua Leisure FF-6915 E User manual Home Gym 1
19 Aqua Leisure Fitness FF-6905 User manual Home Gym 1
20 Aqua Leisure FF-6915 F User manual Home Gym 0